Operation CHARM: Car repair manuals for everyone.
Home >> Infiniti Truck >> 2013 >> JX35 AWD V6-3.5L (VQ35DE) >> Repair and Diagnosis >> Body and Frame >> Seats >> Service and Repair >> Removal and Replacement >> Second Row Seats >> Disassembly and Assembly

Disassembly and Assembly




SECOND ROW SEATS

Exploded View


LH BENCH SEAT






Revision: March 20122013 Infiniti JX






RH SEAT

Revision: March 20122013 Infiniti JX










Revision: March 20122013 Infiniti JX



SECOND ROW SEATS

Disassembly and Assembly


LH BENCH SEAT CUSHION

Disassembly
1.Remove the LH bench seat cushion. Refer to "Seat Cushion" Seat Cushion.
2.Remove support strut from the LH bench seat cushion.
3.Remove the seat cushion assembly from the seat cushion frame.





a.Unzip the back trim cover and release the J-clip retainers (black arrow).
b.Remove four hog rings (A) near seat belt opening, to release seat cushion trim (2).
NOTE:
- Remove all pieces of hog rings and discard them.
c.Carefully remove the seat cushion assembly (1) from the seat cushion frame (3).
4.Separate the seat cushion trim from the seat cushion pad.





a.Pull seat cushion trim (1) up at rear to release hook fastener (A).
: Front b.Remove hog rings and separate the seat cushion trim (1) from the seat cushion pad.
: Hog ring
NOTE:
- Remove all pieces of hog rings and discard them.
c.Route the seat cushion heater unit harness (if equipped) through the opening in the seat cushion trim.
Assembly
Assembly is in the reverse order of disassembly.

CAUTION:
- Make sure hog rings are correctly fastened around both the seat cushion trim and seat cushion pad wires.
- Replace any deformed or damaged hog rings.
- Make sure any old hog ring pieces are removed from seat.
NOTE:
Revision: March 20122013 Infiniti JX





- Install new hog rings on the seat cushion trim in original positions.
- Use only one hog ring in each designated location.
- Be sure hook fastener is pressed into place after seat cushion trim is assembled.

LH BENCH SEATBACK CUSHION

Disassembly
1.Remove the LH bench seat. Refer to "Removal and Installation" Removal and Installation.
2.Remove the LH bench seat cushion. Refer to "Seat Cushion" Seat Cushion.
3.Remove the armrest assembly. Refer to "Armrest Assembly" Armrest Assembly.





4.Remove the outer finisher RH (1).





5.Release the seatback heater unit harness (if equipped) from all attachments.
NOTE:
Note harness attachments and routing locations for proper installation.





6.Release center recliner finisher (1) pawls.
7.Release clip.





8.Remove screws (black arrow) and lift seat cushion latch finisher (2) to remove.










9.Remove screws (black arrow) and pull rear finisher to remove.





10.Remove LH bench seat belt retractor (RH) bottom anchor bolt.
Revision: March 20122013 Infiniti JX





11.Press the headrest holder lock button in, then remove the headrest LH.
12.Remove the headrest holders.

CAUTION:
Before removing headrest holder, check its orientation (front/rear and right/left).





13.Remove the seat belt retractor finisher (1) from seatback assembly (2).
a.Release pawls and lift front of seat belt retractor finisher (1).





b.Push on rear of seat belt tractor finisher (1) to remove.










14.Remove EZ entry lever (3) by pulling firmly.
15.Remove EZ entry finisher (2) from seatback assembly (1).










16.Remove the seatback cushion assembly (2) from the seat frame assembly (1).
a.Release the J-clip retainer (black arrow) at the rear lower edge of seatback.
b.Remove clips that retain seatback trim (2) in place.





c.Release fastening strips (A) from the seat frame assembly (1).
d.Release clips that retain trim behind EZ entry finisher.
e.Carefully remove the seatback assembly (2) from the seat frame assembly (1).
f.Route the seat belt through the opening in the seatback trim (2).
17.Separate the seatback trim from the seatback pad.
Revision: March 20122013 Infiniti JX





a.Pull seatback trim (1) upward in front to release hook fasteners (A).
b.Remove hog rings and separate the seatback trim (1) from the seatback pad.





NOTE:
Remove all pieces of hog rings and discard them.
c.Remove the seatback heater unit (if equipped) harness through the opening in the seatback trim
Assembly
Assembly is in the reverse order of disassembly.

CAUTION:
- Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.
- Replace any deformed or damaged hog rings.
- Make sure any old hog ring pieces are removed from seat.
NOTE:





- Install new hog rings on the seatback trim in original positions.
- Use only one hog ring in each designated location.
- Be sure hook fastener is pressed into place after seatback trim is assembled.

LH BENCH SEAT RECLINE RELEASE CABLE ASSEMBLY

Disassembly
1.Remove the LH bench seatback cushion. Refer to "Disassembly and Assembly" .





2.Remove the recline release cable assembly screws (A).
3.Release (black arrow) the recline release cable assembly.

CAUTION:
Note the cable routing for proper installation.
Revision: March 20122013 Infiniti JX





4.Remove the support finishers (2) and (3).
5.Remove the recline release cable assembly (1) from the RH
side.
6.Remove the recline release cable assembly (1) from LH side.
7.Remove the recline release cable assembly (1).
Assembly
Assembly is in the reverse order of removal.

CAUTION:
Route cables correctly for proper function.

LH BENCH SEAT EZ ENTRY CABLE

Disassembly
1.Remove LH bench seatback cushion. Refer to "Disassembly and Assembly" .
NOTE:
It is not necessary to separate the seatback trim from the seatback pad.





2.Remove recline finisher RH (2) and recline finisher LH (3).
3.Remove EZ entry cable (1) from routing guides (black arrow).

CAUTION:
Note the cable routing for proper installation
4.Remove the EZ entry cable (1) from the RH side.
5.Remove the EZ entry cable (1) from the LH side.
6.Remove the EZ entry cable.
Assembly
Assembly is in the reverse order of removal.
Revision: March 20122013 Infiniti JX

CAUTION:
Route cables correctly for proper function.

RH SEAT CUSHION

Disassembly
1.Remove RH seat cushion. Refer to "Seat Cushion" Seat Cushion.
2.Remove support strut from RH seat cushion.





3.Remove the seat cushion assembly (1) from the seat cushion frame (2).
a.Unzip the back trim cover and release the J-clip retainer (black arrow).
b.Carefully remove the seat cushion assembly (1) from the seat cushion frame (2).
4.Separate the seat cushion trim from the seat cushion pad.





a.Remove hog rings and separate the seat cushion trim (1) from the seat cushion pad.





NOTE:
Remove all pieces of hog rings and discard them.
b.Route the seat cushion heater unit (if equipped) harness through the opening in the seat cushion trim.
Assembly
Assembly is in the reverse order of disassembly.

CAUTION:
- Make sure hog rings are correctly fastened around both the seat cushion trim and seat pad wires.
- Replace any deformed or damaged hog rings.
- Make sure any old hog ring pieces are removed from seat.
NOTE:





- Install new hog rings on the seat cushion trim in original positions.
- Use only one hog ring in each designated location.
- Be sure hook fastener is pressed into place after seat cushion trim is assembled.

RH SEATBACK CUSHION

Disassembly
1.Remove RH bench seat. Refer to "Removal and Installation" Removal and Installation.
2.Remove RH seat cushion. Refer to "Seat Cushion" Seat Cushion.
Revision: March 20122013 Infiniti JX





3.Remove recline lever (3).
a.Remove snap ring (2) upward using a suitable tool.
b.Remove recline lever (3).
4.Remove screw (black arrow) and seat cushion side finisher (1).










5.Remove screws (black arrow) and lift seat cushion latch finisher (1) to remove.





6.Remove the rear finisher.
7.Release the seatback heater unit (if equipped) harness from attachments.
NOTE:
Note harness attachments and routing location for proper installation.





8.Press the headrest holder lock button in, then remove the headrest.
9.Remove the headrest holders.

CAUTION:
Before removing headrest holder, check its orientation (front/rear and right/left).





10.Remove EZ entry lever (1) by pulling firmly.
11.Remove EZ entry finisher (2) from the seatback assembly (3).





Revision: March 20122013 Infiniti JX





12.Remove the tether anchor finisher (2).





13.Remove the seatback board (1).










14.Remove the seatback cushion assembly (1) from the seat frame assembly (2).
a.Release the J-clip retainer (black arrow) at the rear lower edge of seatback.
b.Remove clips that retain seatback trim (1) in place.





c.Remove hog rings.





NOTE:
Remove all pieces of hog rings and discard them.
d.Release fastening strips (A) from the seat frame assembly (2).
e.Release clips that retain trim behind EZ entry finisher.
f.Carefully remove the seatback assembly (1) from the seat frame assembly (2).
15.Separate the seatback trim from the seatback pad.





a.Pull seatback trim (1) upward in front to release hook fasteners (A).
b.Remove hog rings and separate the seatback trim (1) from the seatback pad.





NOTE:
Remove all pieces of hog rings and discard them.
c.Thread the seatback heater unit harness through the opening in the seatback trim

Assembly
Assembly is in the reverse order of disassembly.

CAUTION:
- Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.
- Replace any deformed or damaged hog rings.
- Make sure any old hog ring pieces are removed from seat.
NOTE:





- Install new hog rings on the seatback trim in original positions.
- Use only one hog ring in each designated location.
- Be sure hook fastener is pressed into place after seatback trim is assembled.

Revision: March 20122013 Infiniti JX

RH SEAT RECLINE RELEASE CABLE ASSEMBLY

Disassembly
1.Remove the RH seatback cushion. Refer to "Disassembly and Assembly" .
2.Remove the support finisher.





3.Remove the recline release cable assembly screws (A).
4.Release (black arrow) the recline release cable assembly (1).

CAUTION:
Note the cable routing for proper installation.
5.Remove the recline release cable assembly (1) from routing guide (B).
6.Remove the recline release cable assembly end (C) and the recline release cable assembly (1).
Assembly
Assembly is in the reverse order of removal.

CAUTION:
Route cables correctly for proper function.

EZ ENTRY CABLE

Disassembly
1.Remove the RH seatback cushion. Refer to "Disassembly and Assembly" .
NOTE:
It is not necessary to separate the seatback trim from the seatback pad.
2.Remove the support finisher.





3.Remove EZ entry cable (3) from the routing guide (C).

CAUTION:
Note the cable routing for proper installation.
4.Release (black arrow) the EZ entry cable (3).
5.Remove the track tilt release cable (2) form the seat frame assembly (1) and Release cable end (A).
6.Remove the EZ entry cable end (B).
7.Remove the EZ entry cable.
Assembly
Assembly is in the reverse order of removal.

CAUTION:
Route cables correctly for proper function.

RH SEAT TRACK TILT RELEASE CABLE

Revision: March 20122013 Infiniti JX
Disassembly
1.Remove the RH seatback cushion. Refer to "Disassembly and Assembly" .
NOTE:
It is not necessary to separate the seatback trim from the seatback pad.
2.Release (black arrow) the track tilt release cable (1).

CAUTION:
Note the cable routing for proper installation.
3.Remove the track tilt release cable (1) from the seat frame assembly (2) and Release cable ends (A).
4.Remove the track tilt release cable (1).





Assembly
Assembly is in the reverse order of removal.

CAUTION:
Route cables correctly for proper function.
Revision: March 20122013 Infiniti JX
pro multis · About Operation CHARM