Coolant: Service and Repair

DRAINING PROCEDURE

CAUTION: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot The cooling system will release scalding fluid and steam under pressure if radiator cap or surge tank cap is removed while the engine and radiator are still hot.

CAUTION: As long as there is pressure in the cooling system, the temperature can be considerably higher than the boiling temperature of the solution in the radiator without causing the solution to boil. removal of the radiator cap while the engine is hot and pressure is high will cause the solution to boil instantaneously-possibly with explosive force-spewing the solution over the engine, fenders and the person removing the cap. Under some conditions, the ethylene glycol in the engine coolant is combustible.

CAUTION: An electric fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.

ENGINE COOLANT RECYCLING
The use of a waterless coolant recycling system on the vehicle eliminates the need for evacuation. This method removes the used coolant and replaces it with approved new or with recycled coolant. When this equipment is not available use the following procedure.

NOTICE: Do not add cold water to the cooling system with the engine at or above operating temperature. Adding cold water causes rapid cooling, resulting in possible engine damage.

1. Make sure the system has cooled, then remove the radiator filler cap.
2. Place a drain pan under the radiator drain cock.





3. Install a tube on the drain cock.





4. Place the end of the tube in the drain pan.
5. Open the drain cock completely.
6. Allow the cooling system to drain until the flow stops. If only the radiator is drained, up to 40% of the old coolant will remain in the system.
7. Place a drain pan under the engine.





8. Remove the drain plug from the side of the engine block, 2.2L shown.





9. Remove the drain plugs from each side of the engine block, 4.3L shown.
- There may be more drainage from the radiator at this time.
- Allow the engine block to drain until the flow stops.

NOTICE: Refer to Fastener Notice in Service Precautions. Vehicle Damage Warnings





10. Apply a sealer to the threads and then tighten the engine block drain plug(s).

Tighten
Tighten the engine block drain plugs to 32 Nm (25 ft. lbs.).

IMPORTANT: Dispose of the used engine coolant properly. Store it in a used coolant holding tank awaiting proper disposal or recycling. Never pour used coolant down the drain. Ethylene glycol antifreeze is a very toxic chemical. Disposal into the sewer system or into the ground water is both environmentally irresponsible and illegal.





- If the drained coolant is discolored, flush the cooling system. Refer to Flushing.
- If the drained coolant appears normal, continue with the filling procedure.

FILLING PROCEDURE

NOTICE: Do not use a solution stronger than 70 percent antifreeze. Pure antifreeze can freeze at -22°C (-8°F).

1. Make sure the radiator drain cock is closed.
2. Check the strength of the old coolant, before attempting to reuse it. Refer to Coolant Concentration Testing.
3. When you need additional antifreeze solution:
- Pre-mix ethylene glycol at a ratio of 50/50 with clean, distilled water.
- Distilled water reduces the accumulation of scale in the cooling system.
- For coolant use Dex-Cool orange colored silicate free coolant.
4. Place a large mouth funnel in the radiator fill opening.
5. Slowly add the coolant mixture.
6. Fill to 1/2 inch below the radiator fill opening.
7. Start the engine.
8. As the cooling system warms up and the thermostat opens, the coolant level will drop.
9. Add coolant until the level is up to the radiator fill opening.
- Do not spill the coolant onto the exhaust system or other hot engine parts.
- Under some circumstances, the ethylene glycol in the coolant is combustible.





10. Replace the radiator filler cap.
11. Check the level in the coolant recovery reservoir, add coolant if needed.
12. Test the cooling system for leaks, refer to Cooling System Leak Testing.