Steering Shaft, Lower Bearing, Jacket (Floor Shift)
Steering Shaft, Lower Bearing, Jacket (Floor Shift)Disassembly Procedure
Tools Required
- J 21854-1 Pivot Pin Remover
- J 41688 Centering Sphere Installer
1. Remove the lock module assembly. Refer to Electronic Column Lock Module (Floor Shift).
2. Remove the tilt spring only. Refer to Tilt Spring (Floor Shift).
3. Inspect the steering column for accident damage. Refer to On-Vehicle Service; Tilt Column; Steering Column Accident Damage.
4. Remove the 2 pan head tapping screws (1) from the turn signal and multifunction switch assembly (2).
5. Remove the turn signal and multifunction switch assembly (2).
6. Remove the inner boot seal (4).
7. Remove the steering shaft seal (3) from the adapter and bearing assembly (1).
8. Remove the shaft seal retainer (2) from the adapter and bearing assembly (1).
9. Remove the adapter and bearing assembly (1) from the steering shaft assembly.
10. Remove the 2 pivot pins (3) from the steering column tilt head assembly (1) by using J 21854-1.
11. Install the tilt lever into the steering column tilt head assembly (1).
12. Pull back on the tilt lever and at the same time pull the steering column tilt head assembly (1) down and away from the steering column.
13. Remove the steering column tilt head assembly (1) with the steering shaft assembly from the steering column support assembly (2).
14. Remove the tilt lever.
15. Remove the steering shaft assembly (2) from the steering column tilt head assembly (1).
Important: Mark the race and upper shaft assembly and the lower shaft assembly before disassembly. Failure to assemble the race and upper shaft assembly and the Lower shalt assembly correctly will cause the steering wheel to be turned 180 degrees.
16. Tilt the race and upper shaft assembly (1)90 degrees to the lower shaft assembly (2).
17. Disengage the race and upper shaft assembly (1) from the lower shaft assembly (2).
18. Insert the race and upper shaft assembly (1) into J 41688.
19. Insert J41688 into a vise.
20. Rotate the driver 90 degrees in the counterclockwise direction in order to disengage the centering sphere from the race and upper shaft assembly.
21. Remove the race and upper shaft assembly from J 41688.
22. Remove the shaft preload spring and the centering sphere from J 41688.
23. If necessary, discard the old centering sphere and the old shaft preload spring.
24. Remove the 4 torx head screws (2) from the steering column support assembly (1).
25. Discard the 4 torx head screws.
26. Remove the steering column support assembly (1) from the steering column jacket assembly.
Assembly Procedure
Tools Required
- J 41688 Centering Sphere Installer Tool
Important: Replace the steering column support assembly if the steering column support assembly has been staked 3 times.
1. Attach the steering column support assembly (1) to the steering column jacket assembly with 4 new torx head screws (2).
Tighten
Tighten the 4 torx head screws to 17 N.m (13 lb ft).
2. Lubricate the centering sphere (1) with lithium grease.
3. Install the centering sphere (1) and the joint preload spring (2) by using J 41688.
4. Place the base of J 41688 into a vise.
5. Compress the centering sphere and the joint preload spring.
6. Rotate the driver 90 degrees in the clockwise direction until the arms lock in place.
7. Attach the race and upper shaft assembly (1) to the centering sphere.
8. Rotate the race and upper shaft assembly (1) downward 90 degrees until the centering sphere is locked in place.
9. Remove the race and upper shaft assembly and J 41688 from the vise.
10. Disassemble J 41688 by separating the base.
11. Remove the race and upper shaft assembly, which is now attached to the centering sphere, from J 41688.
12. Apply lithium grease to the exposed steering shaft.
13. Align the lower steering shaft assembly (2) to the race and upper shaft assembly (1) by using the marks.
14. Tilt the lower steering shaft assembly (2) at 90 degrees to the race and upper shaft assembly (1).
15. Install the lower steering shaft assembly (2) onto the race and upper shaft assembly (1).
16. Install the steering shaft assembly (2) into the steering column tilt head assembly (1).
17. Install the steering shaft assembly with the steering column tilt head assembly (1) into the steering column support assembly.
18. Move the tilt lever and push the steering column tilt head assembly up towards the steering column in order to lock the steering wheel lock shoes in place.
19. Lubricate the pivot pins (1) with lithium grease.
20. Firmly seat each pivot pin (1) into the steering column tilt head assembly.
21. Stake the steering column support assembly in 3 locations around each pivot pin (1).
22. Install the adapter and bearing assembly (1) onto the steering column jacket assembly by performing the following steps:
1. Align the tab on the adapter and bearing assembly (1) with the slot in the steering column jacket assembly.
2. Push the adapter and bearing assembly (1) onto the steering shaft assembly
until the tab snaps into the slot.
23. Install the shaft seal retainer (2) onto the adapter and bearing assembly (1).
1. Align the slots of the shaft seal retainer (2) to the ribs of the adapter and bearing assembly (1).
2. Push the shaft seal retainer (2) onto the steering shaft assembly so that the shaft seal retainer (2) contacts the adapter and bearing assembly (1).
24. Install the steering shaft seal (3) onto the steering shaft assembly.
25. Install the inner boot seal (4) onto the steering shaft assembly.
26. Install the turn signal and multifunction switch assembly (2) onto the steering column tilt head assembly.
Important: Be sure that the electrical contact of the turn signal and multi function switch assembly (2) rests on the turn signal cancel cam assembly.
27. Screw the 2 pan head tapping screws (1) into the turn signal and multifunction switch assembly (2).
Tighten
Tighten the 2 pan head tapping screws to 7 N.m (62 lb in).
28. Install the tilt spring only. Refer to Tilt Spring (Floor Shift).
29. Install the lock module assembly. Refer to Electronic Column Lock Module (Floor Shift).