Final Drive - Renew

- Open the door.
- Remove the screws securing the passenger side dash liner and remove the dash liner.
- Remove the fuel pump relay from the multi plug (second relay from the left, red multi plug).
- Open the drivers door and crank the engine for 10 seconds to depressurize the fuel system.
- Slacken the rear road wheel nuts 1/4 of a turn each.
- Jack up the vehicle and place on one stand.
- Remove one road wheel securing nut, mark the road wheel relative to a stud and remove the remaining nuts.
- Remove the road wheel and tire assembly.
- Repeat the procedure for the other rear road wheel.
- From below, cut the ratchet straps securing the fuel pump feed hose to the axle carrier.
- Fit pipe clamps to the feed hose, slacken the clip securing the feed hose to the fuel pump and disconnect the hose.
- From above, slacken the filter hose union at the pump and disconnect.
- Fit plugs to the pump and hose.
- Remove the nuts securing the fuel pump to the axle carrier and position the pump upwards and forwards away from its mounting.
- Peel back the rubber insulation boots from the pump terminals and remove the nuts securing the feed wires to the terminals and remove the fuel pump.
- Slacken the clamp securing the mounting clamp to the pump and remove the clamp.
- Remove the mounting rubber and non-return valve from the pump.
- Remove the caliper lower securing bolt, pivot the caliper for access to the brake pads and remove the outer brake pad disconnect the inner pad wear sensor block connector.
- Remove the remaining caliper securing bolt and secure the caliper to the bump stop.
- Repeat the procedure for the second caliper.
- Cut the ratchet straps securing the wear sensors to the suspension unit.



- Remove the bolts securing the speed sensor to the final drive and displace the sensor from its mounting (Fig 1).
- Discard the gasket.



- Remove the clevis (1 Fig 1) and split pin (2 Fig 1) securing the handbrake cable (3 Fig 1) to the yoke (4 Fig 1), collect the washer.
- Disconnect the rear cables at the joiner and remove the yoke from the cable.
- Remove the bolts (5 Fig 1) securing the propeller shaft (6 Fig 1) to the differential drive flange and separate the flanges.
- Remove the bolts securing the overaxle pipe mountings to the subframe.
- Take the weight of the rear suspension on a jack.
- Remove the bolts securing the front mounting to the body, collect the mounting bracket, bolt and spacer.
- Disconnect the rubber from the body mounting peg.
- Disconnect the subframe mounting rubber from the body mounting peg.



- Remove the rear differential strut to body securing bolt (1 Fig 2).



- Remove shock absorber lower securing bolt (1 Fig 3) and nut.
- Repeat the procedure for the other side.
- Lower the unit from the vehicle on the jack and manoeuvre from beneath the vehicle.
- Remove the nuts and bolts securing the drive shaft to the differential output flange.
- Remove the circlip securing the handbrake outer cable to the frame and remove the cable from the frame.
- Disconnect the drive shaft from the output shaft and collect the camber shim.
- Remove the lower wishbone fulcrum bolt securing nut and drift out the bolt.



- Remove the fulcrum tube (1 Fig 1), spacing washers (2 Fig 1) and remove the lower wishbone/drive shaft assembly (3 Fig 1).
- Repeat the procedure for the second side.
- Invert the assembly and remove the nuts securing the differential to the carrier.
- Remove the spacers and rear carrier assembly.
- Remove the subframe lower securing bolts and rear bracket.
- Remove the bolts securing the final drive nose plate.
- Remove the nuts securing the final drive to the front carrier/front frame.



- Remove the nuts and bolts securing the tie bar to the final drive (Fig 2).
- Remove the subframe assembly.
- Remove the front frame to front carrier spacers and remove the front carrier.
- Remove the nose plate securing studs and the rear pendulum bolts.
- Remove the bolts securing the road speed sensor mounting bracket to the differential and collect the bracket.
- Clean all components and check for wear and distortion.
- Reverse the removal procedure to fit the replacement differential unit.
- Ensure that the differential unit is filled with new oil.
- Lift the road wheel and tire assembly up to the hub, align the wheel with the marked stud and secure with the nuts.
- Take the weight of the vehicle with a jack, remove the axle stand, lower the vehicle and recheck the torque of the wheel nuts.
- Repeat the procedure for the second side.
- Close the door, refit the relay and dash liner.
- Secure the dash liner with the screws.
- Close the door.

TORQUE FIGURES
Caliper to carrier 31 - 40 Nm
Differential strut to top mounting bracket 80 - 100 Nm
Differential strut top mounting bracket to body 45 - 55 Nm
Differential strut to wishbone tie 85 - 105 Nm
Drive shaft to differential 78 - 95 Nm
Frame centre boss 92 - 112 Nm
Frame outer bracket 92 - 110 Nm
Frame to rear mounting (frame middle boss) 92 - 112 Nm
Front mounting to axle carrier 22 - 28 Nm
Fuel feed hose to pump (clip) 2.2 - 2.5 Nm
Fuel pump feed hose to pump (union) 10 - 12 Nm
Fuel pump mounting bracket to axle carrier 7 - 10 Nm
I.R.S. frame cone to differential 92 - 112 Nm
Lower mounting bracket to body (to weld nut) 40 - 50 Nm
Lower mounting bracket and rear frame to body(through bush) 80 - 100 Nm
Mounting bracket to drive unit 45 - 55 Nm
Pendulum to differential mounting stud 160 - 200 Nm
Propeller shaft to differential 95 - 105 Nm
Road speed sensor mounting bracket to differential 22 - 28 Nm
Road speed sensor to mounting bracket 7 - 8 Nm
Spring and damper to wishbone 160 - 200 Nm
Stud differential nose 47 - 57 Nm
Upper link mounting 92 - 112 Nm
Upper pendulum mounting stud to differential 365 - 415 Nm
Wheel nut to wheel stud (STEEL WHEEL) 65 - 85 Nm
Wheel nut to wheel stud (ALLOY WHEEL) 88 - 102Nm
Wishbone to drive unit 85 - 105 Nm

SPANNER SIZES
8 mm
10 mm
13 mm
17 mm
19 mm
22 mm
24 mm
30 mm

9/16" AF
11/16" AF

OILS/GREASES/SEALANTS
Caliper to carrier bolts/guide pins Molykote 111
Lower shock absorber bolt Castrol LM Multipurpose Grease.
Lower wishbone to differential pendulum shaft Castrol LM Multipurpose Grease.
Sub frame center and rear securing bolts Loctite
Differential oil Shell Spirax Super 90