Operation CHARM: Car repair manuals for everyone.
Home >> Jeep Truck >> 2010 >> Commander 2WD V8-5.7L >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> B Code Charts >> B1883

B1883






B1883-POWER LIFTGATE POSITION SENSOR 1 CIRCUIT PERFORMANCE





For a complete wiring diagram, refer to the Wiring Information.

- When Monitored:
Whenever the Power Liftgate Module is power opening or closing.

- Set Condition:
When the Power Liftgate Module senses the (Q204) Position Sensor Signal 1 circuit not pulsing during motor operation, this code will set.





1. CHECK FOR DTCS
1. Using the scan tool, record DTCs.
2. Erase DTCs.
3. Turn the ignition off, wait 10 seconds, then turn the ignition on.
4. If possible, operate the liftgate several times.
5. Using the scan tool, read DTCs.

Does the scan tool display B1883-POWER LIFTGATE POSITION SENSOR 1 CIRCUIT PERFORMANCE?

Yes

- Go To 2

No

- Using the wiring diagram/schematic as a guide, inspect the wiring and connectors for an intermittent condition.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

2. (Q901) LOGIC GROUND OPEN




1. Turn the ignition off.
2. Disconnect the Power Liftgate Drive Unit harness connector.
3. Measure the resistance between the (Z800) Ground and the (Q901) Logic Ground circuit in the Power Liftgate Drive Unit harness connector.

Is the resistance below 9.5 Ohms?

Yes

- Go To 3

No

- NOTE: The (Q901) Logic Ground circuit is grounded through the Power Liftgate Module and the (Z800) Ground circuit.
- Repair the (Q901) Logic Ground circuit for an open.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

3. (Q204) POSITION SENSOR SIGNAL 1 CIRCUIT SHORTED TO GROUND




1. Disconnect the Power Liftgate Module C1 harness connector.
2. Measure the resistance between ground and the (Q204) Position Sensor Signal 1 circuit.

Is the resistance below 10000.0 Ohms?

Yes

- Repair the (Q204) Position Sensor Signal 1 circuit for a short to ground.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 4

4. (Q204) POSITION SENSOR SIGNAL 1 CIRCUIT SHORT TO VOLTAGE




1. Turn the ignition on.
2. Measure the voltage between ground and the (Q204) Position Sensor Signal 1 circuit.

Is there any voltage present?

Yes

- Repair the (204) Position Sensor Signal 1 circuit for a short to voltage.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 5

5. (Q204) POSITION SENSOR SIGNAL 1 CIRCUIT OPEN




1. Turn the ignition off.
2. Measure the resistance of the (Q204) Position Sensor Signal 1 circuit between the Power Liftgate Module C1 harness connector and the Power Liftgate Drive Unit harness connector.

Is the resistance below 5.0 Ohms?

Yes

- Go To 6

No

- Repair the (Q204) Position Sensor Signal 1 circuit for an open.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

6. (Q203) POSITION SENSOR SUPPLY CIRCUIT OPEN




1. Measure the resistance of the (Q203) Position Sensor Supply circuit between the Power Liftgate Module C1 harness connector and the Power Liftgate Drive Unit harness connector.

Is the resistance below 5.0 Ohms?

Yes

- Go To 7

No

- Repair the (Q203) Position Sensor Supply circuit for an open.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

7. (Q203) POSITION SENSOR SUPPLY CIRCUIT SHORTED TO GROUND




1. Measure the resistance between ground and the (Q203) Position Sensor Supply circuit.

Is the resistance below 10,000 Ohms?

Yes

- Repair the (Q203) Position Sensor Supply circuit for a short to ground.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 8

8. (Q203) POSITION SENSOR SUPPLY CIRCUIT SHORTED TO VOLTAGE




1. Turn the ignition on.
2. Measure the voltage between the (Q901) Logic Ground circuit and the (Q203) Position Sensor Supply circuit in the Power Liftgate Drive Unit connector.

Is the voltage above 5.5 Volts?

Yes

- Repair the (Q203) Position Sensor Supply circuit for a short to voltage. If the power liftgate is inoperative after repairing the (Q203) Position Sensor Supply circuit, replace the Power Liftgate Drive Unit.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 9

9. (Q204) POSITION SENSOR SIGNAL 1 CIRCUIT SHORTED TO THE (Q205) POSITION SENSOR SIGNAL 2 CIRCUIT




1. Measure the resistance between the (Q204) Position Sensor Signal 1 circuit and the (Q205) Position Sensor Signal 2 circuit.

Is the resistance below 10,000 Ohms?

Yes

- Repair the (Q204) Position Sensor Signal 1 circuit for a short to the (Q205) Position Sensor Signal 2 circuit.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 10

10. POWER LIFTGATE MODULE




1. Reconnect the Power Liftgate Module C1 harness connector.
2. Reconnect the Power Liftgate Module C2 harness connector.
3. Turn the ignition on.
4. Measure the voltage of the (Q204) Position Sensor Signal 1 circuit and the (Q203) Position Sensor Supply circuit ground in the Power Liftgate Drive Unit harness connector.

Is the voltage approximately 5.0 Volts for both measurements?

Yes

- Replace the Power Liftgate Drive Unit.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Replace the Power Liftgate Module.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

pro multis · About Operation CHARM