P3450
P3450-CYLINDER 7 DEACTIVATION CONTROL PERFORMANCE
For a complete wiring diagram, refer to the Wiring Information.
Theory of Operation
When all criteria has been met, power is supplied to each Multiple Displacement System (MDS) solenoid when the engine is making a transition from 8 cylinder mode to 4 cylinder mode. By actuating the solenoid, oil pressure is raised to the pair of lifters that coincide with each particular solenoid. The oil pressure pushes in the locking pins that allows the lifter to collapse, decoupling the valves and camshaft.
- When Monitored:
Transition from 8 to 4 cylinder mode.
- Set Condition:
The MDS fails to disengage for cylinder 7. Two trip fault.
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. Pre-Diagnostic Troubleshooting Procedure.
1. ACTIVE DTC
NOTE: Diagnose any Misfire DTCs before continuing.
1. Start the engine and allow it to reach normal operating temperature.
WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
NOTE: It may be necessary to test drive the vehicle in order for this DTC to set.
2. With the scan tool, select View DTCs.
Is the DTC Active at this time?
Yes
- Go To 2
No
- Perform the INTERMITTENT CONDITION diagnostic procedure. Intermittent Condition Test.
2. CHECKING PCM CONTROL SIDE FOR THE MDS SOLENOID (C140)
1. Turn the ignition off.
2. Disconnect the C140 harness connector.
3. Using a 12-volt test light, jumper from the (Z908) Ground circuit and the (K454) MDS Solenoid No.7 Control circuit in the C140 harness connector (PCM side).
4. Turn the ignition on.
5. With the scan tool, actuate the MDS Solenoid No.7.
NOTE: The test light should be illuminated and bright proportional to the maximum duty cycle allowed by the scan tool. For example, if the scan tool allows 100% actuation, the brightness should be as bright as a direct connection to the battery. If the scan tool allows a maximum 25% actuation, the brightness should be 25% as bright as a direct connection to the battery.
Does the test light illuminate accordingly during the actuation?
Yes
- Go To 3
No
- Go To 4
3. MDS SOLENOID RESISTANCE
1. Turn the ignition off.
2. Measure the resistance between the (Z908) Ground Circuit and the (K454) MDS Solenoid No.7 Control Circuit in the C140 harness connector (MDS side).
NOTE: It is important to follow the below temp/resistance values to ensure an accurate reading.
Is the resistance within an acceptable range?
Yes
- Go To 7
No
- Visually and Physically inspect the wiring harness between the C140 connector and the MDS Solenoid connector. Repair as necessary. If OK, replace the MDS Solenoid.
4. (Z908) GROUND CIRCUIT OPEN (PCM SIDE)
1. Turn the ignition off.
2. Using a 12-volt test light connected to 12-volts, probe the (Z908) Ground circuit in the C140 harness connector (PCM side).
Does the test light illuminate brightly?
Yes
- Go To 5
No
- Repair the open in the (Z908) Ground circuit.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
5. (K454) MDS SOLENOID NO.7 CONTROL CIRCUIT SHORTED TO GROUND (PCM SIDE)
1. Turn the ignition off.
2. Disconnect the C3 PCM harness connector.
3. Measure the resistance between ground and the (K454) MDS Solenoid No.7 Control circuit in the C140 harness connector.
Is the resistance below 100 Ohms?
Yes
- Repair the short to ground in the (K454) MDS Solenoid No.7 Control circuit between the PCM harness connector and the C140 harness connector.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
No
- Go To 6
6. (K454) MDS SOLENOID NO.7 CONTROL CIRCUIT OPEN (PCM SIDE)
CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install PCM Pinout Box 8815 to perform diagnosis.
1. Measure the resistance of the (K454) MDS Solenoid No.7 Control circuit from the C140 harness connector to the appropriate terminal of PCM Pinout Box 8815.
Is the resistance below 5.0 Ohms?
Yes
- Replace and program the Powertrain Control Module.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
No
- Repair the open in the (K454) MDS Solenoid No.7 Control circuit between the C140 harness connector and the PCM harness connector.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
7. MDS SOLENOID 7
1. Turn the ignition off.
2. Remove the Intake Manifold.
3. Reconnect the C3 PCM harness connector.
4. Turn the ignition on.
5. With the scan tool actuate the MDS Solenoid 7.
Can you feel and hear the Solenoid Actuating?
Yes
- Go To 8
No
- Remove the Solenoid (1) and check for any debris that may be blocking the oil passages (3) to the Solenoid. If the passages are clogged, clean the passages and replace the MDS Solenoid 7. If the passages are not clogged with debris, replace the MDS Solenoid 7.
8. OIL PASSAGES RESTRICTED
1. Turn the ignition off.
2. Remove both Solenoids on Bank 1 of the engine block.
3. Remove the Bank 1 Cylinder Head.
4. Remove the Lifters from the right engine bank.
5. Inspect the oil passages to the Solenoids and from the Solenoids to the lifters.
Are the passages blocked?
Yes
- Clean the oil passages as necessary. If the entire engine is restricted disassembly of the entire engine block may be necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.
No
- Replace both sets of lifters if no other possible causes remain.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.