Operation CHARM: Car repair manuals for everyone.
Home >> Jeep Truck >> 2010 >> Wrangler 4WD V6-3.8L >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> U Code Charts >> U0001 >> Totally Integrated Power Module (TIPM)

Totally Integrated Power Module (TIPM)






U0001-CAN C BUS CIRCUIT







- When Monitored:
With the ignition on.

- Set Condition:
The Totally Integrated Power Module (TIPM) detects a corrupt CAN C Bus message.





1. TEST FOR INTERMITTENT CONDITION
1. Turn the ignition on.
2. Using the scan tool, record and erase TIPM DTCs.
3. Cycle the ignition from on to off three times.
4. Turn the ignition on.
5. Using the scan tool, read active TIPM DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 2

No

- The conditions that caused this code to set are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.

2. ANTILOCK BRAKE MODULE - INTERNAL SHORT
1. Turn the ignition off.
2. Disconnect the Antilock Brake Module harness connector.
3. Turn the ignition on.
4. Using the scan tool, record and erase TIPM DTCs.
5. Cycle the ignition from on to off three times.
6. Turn the ignition on.
7. Using the scan tool, read active TIPM DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 3

No

- Inspect the wiring and connectors for damage or shorted circuits.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.

3. POWERTRAIN CONTROL MODULE - INTERNAL SHORT
1. Turn the ignition off.
2. Disconnect the Powertrain Control Module C1 harness connector.
3. Turn the ignition on.
4. Using the scan tool, record and erase TIPM DTCs.
5. Cycle the ignition from on to off three times.
6. Turn the ignition on.
7. Using the scan tool, read active TIPM DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 4

No

- Inspect the wiring and connectors for damage or shorted circuits. If okay, replace and program the Powertrain Control Module.
- Perform the POWERTRAIN VERIFICATION TEST. Powertrain Verification Test.

4. ENGINE CONTROL MODULE (DIESEL ONLY) - INTERNAL SHORT
1. Turn the ignition off.

NOTE: If vehicle is not equipped with this module, answer yes to the question.

2. Disconnect the Engine Control Module harness connectors.
3. Turn the ignition on.
4. Using the scan tool, record and erase TIPM DTCs.
5. Cycle the ignition from on to off three times.
6. Turn the ignition on.
7. Using the scan tool, read active TIPM DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 5

No

- Inspect the wiring and connectors for damage or shorted circuits. If okay, replace and program the Engine Control Module.
- Perform the ECM VERIFICATION TEST.

5. TRANSMISSION CONTROL MODULE - INTERNAL SHORT
1. Turn the ignition off.

NOTE: If vehicle is not equipped with this module, answer yes to the question.

2. Disconnect the Transmission Control Module harness connectors.
3. Turn the ignition on.
4. Using the scan tool, record and erase TIPM DTCs.
5. Cycle the ignition from on to off three times.
6. Turn the ignition on.
7. Using the scan tool, read active TIPM DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 6

No

- Inspect the wiring and connectors for damage or shorted circuits. If okay, replace and program the Transmission Control Module.
- Perform the appropriate transmission related Verification Test. Verification Tests

6. STEERING ANGLE SENSOR - INTERNAL SHORT
1. Turn the ignition off.

NOTE: If vehicle is not equipped with this module, answer yes to the question.

2. Disconnect the Steering Angle Sensor harness connector.
3. Turn the ignition on.
4. Using the scan tool, record and erase TIPM DTCs.
5. Cycle the ignition from on to off three times.
6. Turn the ignition on.
7. Using the scan tool, read active TIPM DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 7

No

- Inspect the wiring and connectors for damage or shorted circuits. If okay, replace the Steering Angle Sensor.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

7. AUTOMATIC SWAY BAR SYSTEM MODULE - INTERNAL SHORT
1. Turn the ignition off.

NOTE: If vehicle is not equipped with this module, answer yes to the question.

2. Disconnect the Automatic Sway Bar System Module harness connector.
3. Turn the ignition on.
4. Using the scan tool, record and erase TIPM DTCs.
5. Cycle the ignition from on to off three times.
6. Turn the ignition on.
7. Using the scan tool, read active TIPM DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 8

No

- Inspect the wiring and connectors for damage or shorted circuits. If okay, replace the Automatic Sway Bar System Module.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

8. WIRELESS CONTROL MODULE - INTERNAL SHORT
1. Turn the ignition off.

NOTE: If vehicle is not equipped with this module, answer yes to the question.

2. Disconnect the Wireless Control Module harness connector.
3. Turn the ignition on.
4. Using the scan tool, record and erase TIPM DTCs.
5. Cycle the ignition from on to off three times.
6. Turn the ignition on.
7. Using the scan tool, read active TIPM DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 9

No

- Inspect the wiring and connectors for damage or shorted circuits. If okay, replace the Wireless Control Module.
- Perform the WIRELESS CONTROL MODULE (WCM) VERIFICATION TEST. Wireless Control Module (WCM) Verification Test.

9. OCCUPANT RESTRAINT CONTROLLER - INTERNAL SHORT
1. Turn the ignition off.

NOTE: If vehicle is not equipped with this module, answer yes to the question.

WARNING: Turn the ignition off disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

2. Disconnect the Occupant Restraint Controller harness connectors.

WARNING: Turn the ignition on, then reconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

3. Using the scan tool, record and erase TIPM DTCs.
4. Cycle the ignition from on to off three times.
5. Turn the ignition on.
6. Using the scan tool, read active TIPM DTCs.

Does the scan tool display this DTC as active?

Yes

- Go To 10

No

- Inspect the wiring and connectors for damage or shorted circuits. If okay, replace the Occupant Restraint Controller.
- Perform the AIRBAG SYSTEM VERIFICATION TEST. Airbag System Verification Test.

10. (D64) CAN C BUS (-) CIRCUIT SHORTED TO VOLTAGE




1. Measure the voltage between the (D64) CAN C Bus (-) circuit and ground.

Is there any voltage present?

Yes

- Repair the (D64) CAN C Bus (-) circuit for a short to voltage.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 11

11. (D65) CAN C BUS (+) CIRCUIT SHORTED TO GROUND




1. Turn the ignition off.
2. Measure the resistance between ground and the (D65) CAN C Bus (+) circuit.

Is any resistance present?

Yes

- Repair the (D65) CAN C Bus (+) circuit for a short to ground.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Go To 12

12. (D65) CAN C BUS (+) CIRCUIT SHORTED TO (D64) CAN C BUS (-) CIRCUIT




1. Measure the resistance between the (D65) CAN C Bus (+) circuit and the (D64) CAN C Bus (-) circuit.

Is any resistance present?

Yes

- Repair the (D65) CAN C Bus (+) circuit for a short to the (D64) CAN C Bus (-) circuit.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

No

- Inspect the wiring and connectors for damage or shorted circuits. If okay, replace and program the Totally Integrated Power Module.
- Perform the BODY VERIFICATION TEST. Body Verification Test.

pro multis · About Operation CHARM