Engine Controls - MIL ON/DTC P0111 Set
Model: Sportage [KM]Group: Fuel System(14)
Number: KT2006081801
Date: Tuesday, August 22, 2006
Area: N. America
Subject
Sportage PCM Reprogram (DTC P0111) (Engine - 024)
Description
This service bulletin provides information related to the Powertrain Control Module (PCM) upgrade. Some 2005 and 2006 Sportage vehicles with a 2.0L Beta (4 cylinder) engine may experience a Malfunction Indicator Lamp (MIL) "ON" condition with DTC P0111 (Intake Air Temperature Circuit Range/performance problem) stored in the PCM memory even though no IAT or circuit related malfunction exists. To correct this condition, the PCM should be reprogrammed using the Hi-Scan Pro download as described in this bulletin before attempting to repair this concern.
*NOTICE
^ A fully charged battery is necessary before reprogramming can take place. DO NOT connect a battery charger to the vehicle during reprogramming. Make sure the blower motor is "OFF" during programming.
^ All reprogramming must be done with the ignition key in the "ON" position.
^ Be careful not to disconnect any cables connected to the vehicle or HI-Scan Pro during the reprogramming procedure.
^ DO NOT start the engine during reprogramming.
^ DO NOT turn the ignition key "OFF" or interrupt the power supply during reprogramming.
^ When the reprogramming is completed, turn the ignition key "OFF" and wait 20 seconds before starting the engine.
^ ONLY use approved reprogramming software designated for the correct model, year and engine size. Failure to do so may create other driveability issues due to the use of the incorrect ECM/PCM calibration.
ECU ROM ID INFORMATION TABLE
Download the latest Hi-Scan Pro reprogramming software for the 32MB (blue label) reprogramming card from the "Downloads page on the Kia Global Information System (KGIS)
Note:
Global Diagnostic System (GDS) users should access the "Notice" function from the GDS Main Screen for instructions regarding this reprogramming event.
Effective Vehicle Information
AFFECTED PRODUCTION RANGE:
2005 and 2006 Sportage vehicles with 2.0L Beta (4 cylinder) engine.
Service Procedure
1. Install the Hi-scan tool and verify version of ECM ROM ID before attempting to reflash the ECM.
If the ROM ID is "K6NCSP6A", the ECM has the latest update, diagnose p0111 using the appropriate service information.
2. Connect the scan tool cable to the OBDII connector located on the underside of the dash on the driver's side as shown.
3. Remove the system software card from the Hi-Scan Pro and insert the blue reprogramming software card with the new ECM program into the Hi- Scan Pro upper slot.
4. Turn the ignition switch to the ON position. Turn the Hi-Scan Pro ON and press ENTER. Select option "KM 2.0 BETA P0111 DTC Logic Improvement" and press ENTER.
5. Select automatic reprogramming mode, enter "0525" as the password and press ENTER.
6. The reprogramming screen will be displayed with your current ROM ID and the new ROM ID will be shown. This download will take approximately 12 minutes to complete.
7. When "REPROGRAMMING IS COMPLETED" message is displayed, turn the Hi-Scan Pro OFF.
8. Turn the ignition key OFF for about 20 seconds and start the engine to confirm proper operation.
9. Check for diagnostic trouble codes using the Hi-Scan Pro with the system software card and erase any trouble codes stored in the Engine, Transmission, ESP or 4 wheel drive control modules.
MANUAL REPROGRAMMING PROCEDURE:
1. Turn the ignition switch to the ON position.
2. Turn the Hi-Scan Pro ON and press ENTER.
3. Select option "KM 2.0 BETA P0111 DTC logic Improvement" and press ENTER.
4. Select option "KM 2.0 BETA P0111 DTC logic Improvement [ERROR]" and press ENTER.
5. Choose the vehicle type which is correct for your vehicle by using the Information Table.
Enter the password which is correct for your vehicle and press ENTER.
6. When "REPROGRAMMING COMPLETED" message is displayed, turn the Hi-Scan Pro OFF.
7. Turn the ignition key OFF for about 20 seconds and start the engine to confirm proper operation.
8. Check for diagnostic trouble codes using the Hi-Scan Pro with system software card and erase any trouble codes in the Engine, Transaxle, ESP or 4 wheel drive control modules.
MANUAL REFLASH PROGRAMMING NOTES:
^ Manual reprogramming must be performed only when automatic reprogramming fails.
^ If automatic reprogramming fails, turn the ignition switch OFF for about 10 seconds, place it back in the ON position and then perform manual reprogramming.
Error Mode Passwords:
WARRANTY CLAIM INFORMATION: