PSD
B1223Component Location:
General Description
Power sliding door (hereinafter PSD) is the system which moves sliding door of vehicle by electronic motor so that user can open or close door with less force than required on manual operation. After turned on, PSD ECU monitors vehicle speed signal from VSS directly. When power door open signal is received, PSD ECU checks vehicle speed before operation and if vehicle speed is above 5 Km/h (3.10 MPH), PSD ECU cancels power door operation command for safety (but In case of IG "ON", if shift lever is in 'P' or 'N' position, power door operation is not prohibited)
DTC Description
The ECM sets DTC B1223 if number of ignition cycles without VSS value over 5 km/h is greater than 10.
DTC Detecting Condition:
Schematic Diagram (Part 1):
Schematic Diagram (Part 2):
Signal Waveform:
Monitor Scantool Data
1. Connect scantool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Monitor the "Vehicle Speed Slow Status" Parameter on the Scantool. While changing vehicle speed.
Specification : vehicle speed 5 Km/h (3.10 MPH) or more -> HIGH, 5 Km/h (3.10 MPH) or less -> LOW
4. Is the measured current data within specifications?
YES - Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.
NO - Go to "Inspection & Repair" procedure.
Terminal and Connector Inspection
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.
2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage.
3. Has a problem been found?
YES - Repair as necessary and go to "Verification Vehicle Repair" procedure.
NO - Go to "W/Harness Inspection" procedure.
Signal Circuit Inspection
1. Check for open in harness
1. Ignition "ON" & engine "OFF"
2. Measure resistance between terminal "F28-2-4, F27-2-4" of PSD and terminal "1" of vehicle speed sensor.
Specification : Approx. 0 ohm
3. Is the measured resistance within specifications?
YES - Go to "Check for short in harness" procedure.
NO - Check for open in signal harness. Repair as necessary and go to "Verification of Vehicle Repair" procedure.
2. Check for short in harness
4. Ignition "ON" & engine "OFF"
5. Measure resistance between terminal "F28-2-4, F27-2-4" of PSD and chassis ground.
Specification : Approx. Infinity ohms
6. Is the measured resistance within specifications?
YES - Go to "Power circuit Inspection" procedure.
NO - Check for short in signal harness. Repair as necessary and go to "Verification of Vehicle Repair" procedure.
Power Supply Circuit Inspection
1. Check for open/short in harness
1. Ignition "OFF"
2. Disconnect vehicle speed sensor.
3. Ignition "ON".
4. Measure voltage between terminal "1" of vehicle speed sensor and chassis ground.
Specification : 9 - 16 V
5. Is the measured voltage within specifications?
YES - Go to "Ground circuit Inspection" procedure.
NO - Check for open or short in harness. Repair as necessary and go to "Verification of Vehicle Repair" procedure.
Ground Circuit inspection
1. Check for open/short in harness
1. Ignition "OFF"
2. Disconnect vehicle speed sensor.
3. Ignition "ON"
4. Measure voltage between terminal "3" of vehicle speed sensor and chassis ground.
5. Measure voltage between terminal "1" and "2" of vehicle speed sensor.
Specification : |(Voltage from procedure 4) - (Voltage from procedure 5)| < 200 mV
6. Is the difference between two measured voltage within specifications?
YES - Go to "Component Inspection" procedure.
NO - Check for open/short circuit in ground harness. Repair as necessary and go to "Verification of Vehicle Repair" procedure.
Component Inspection
1. Check Vehicle speed sensor
1. Ignition "ON"
2. Connect the vehicle speed sensor connector.
3. Measure waveform between terminal 3 of the sensor harness connector and chassis ground.
Measure waveform of vehicle speed sensor with driving the lifted vehicle
Specification : Refer Signal Waveform & Data in General Information
4. Is waveform measured near the specified form in General information?
YES - Go to "Check PSD" procedure.
NO - Substitute with a known-good vehicle speed sensor and check for proper operation. If the problem is corrected, replace vehicle speed sensor and then go to "Verification Vehicle Repair" procedure.
2. Check PSD
5. Connect scantool to Data Link Connector (DLC).
6. Ignition "ON" & engine "OFF"
7. Substitute with a known-good PSD and Check if the DTC is erased
8. Is the DTC erased?
YES - Substitute with a known-good PSD and check for proper operation.
If the problem is corrected, replace PSD and then go to "Verification of Vehicle Repair" procedure.
NO - Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.
Verification of Vehicle Repair
After a repair, it is essential to verify that the fault has been corrected.
1. Connect scantool and select "Diagnostic Trouble Codes (DTCs)" mode and then clear DTC.
2. Operate the vehicle and monitor the DTC on the scantool.
3. Are any DTCs present?
YES - Go to the applicable troubleshooting procedure.
NO - System is performing to specification at this time.