B2332

B2332

Component Location:

General Description
ADM is a node of CAN communication system which consists of IPM. FAM, RAM, DDM, IMS. Main function of ADM is lock/unlock of door and window, adjusting position and fold/unfold of outside mirror. Door lock actuator consists of motor and monitoring switch. According to Switch signal of ADM, Door lock actuator operates motor to lock/unlock door and monitoring switch delivers result to ADM by voltage value

DTC Description
The ECM sets DTC B2332 if there's short circuit in assist door lock actuator circuit harness

DTC Detecting condition:

Schematic Diagram:

Monitor Scantool Data
1. Connect scantool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Select "Diagnostic Trouble Codes (DTCs)" mode and monitor "DTC Status" parameter
4. Is the DTC B2332 present?

YES - Go to "Inspection & Repair" procedure

NO - Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and ECM memory was not cleared.
Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.

Terminal and Connector Inspection
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.
2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage.
3. Has a problem been found?

YES - Repair as necessary and go to "Verification Vehicle Repair" procedure

NO - Go to "W/Harness Inspection" procedure

Signal Circuit Inspection

Check for short in harness
1. Ignition "OFF"
2. Disconnect driver Door lock actuator.
3. Measure resistance between terminal "9" of ADM and chassis ground

Specification : Approx. Infinity ohms






4. Is the measured resistance within specifications?

YES - Go to "Power circuit Inspection" procedure.

NO - Check for short in signal harness. Repair as necessary and go to "Verification of Vehicle Repair" procedure.

Power Supply Circuit Inspection

Motor Power circuit Inspection
1. Ignition "OFF"
2. Disconnect driver Door lock actuator.
3. Measure resistance between terminal "5" of ADM and chassis ground

Specification : Approx. Infinity ohms






4. Is the measured resistance within specifications?

YES - Go to "Component Inspection" procedure.

NO - Check for short in power harness. Repair as necessary and go to "Verification of Vehicle Repair" procedure.

Component Inspection

Check driver Door lock actuator
1. Connect scantool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Select 'ACTUATION TEST' mode on scantool and press [F1] to start






4. Does driver Door lock actuator work properly?

YES - Go to "Check driver Door lock monitoring switch" procedure.

NO - Substitute with a known-good driver Door lock actuator and check for proper operation. If the problem is corrected, replace driver Door lock actuator and then go to "Verification of Vehicle Repair" procedure.

Check driver Door lock monitoring switch
5. Connect scantool to Data Link Connector (DLC).
6. Ignition "ON" & engine "OFF"
7. Measure voltage value between terminal "9" of ADM and chassis ground. While operating assist door lock actuator

Specification : Door lock -> 5 V, Door unlock -> 0 V






8. Is the measured voltage within specifications?

YES - Go to "Check ADM" procedure.

NO - Substitute with a known-good driver Door lock actuator and check for proper operation. If the problem is corrected, replace driver Door lock actuator and then go to "Verification of Vehicle Repair" procedure.

Check ADM
9. Connect scantool to Data Link Connector (DLC).
10. Ignition "ON" & engine "OFF"
11. Measure voltage value between terminal "5" of ADM and chassis ground. While operating driver door lock switch.

Specification : 9 - 16 V






12. Is the measured voltage within specifications?

YES - Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.

NO - Substitute with a known-good ADM and check for proper operation.
If the problem is corrected, replace ADM and then go to "Verification of Vehicle Repair" procedure.

Verification of Vehicle Repair
After a repair, it is essential to verify that the fault has been corrected.
1. Connect scantool and select "Diagnostic Trouble Codes (DTCs)" mode and then clear DTC
2. Operate the vehicle and monitor the DTC on the scantool
3. Are any DTCs present?

YES - Go to the applicable troubleshooting procedure

NO - System is performing to specification at this time.