Emissions - California Emissions Data Extraction
GROUP EngineNUMBER 090
MODEL 2011MY Sedona (VQ), Rio (JB)
DATE February 2011
SUBJECT:
DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA FROM ECU (DC002)
This bulletin provides information related to extracting "In use performance tracking" missions data from the engine control unit (ECU) in certain vehicles sold in California. The California Air Resource Board (GARB) requires this emissions data to be extracted from the ECUs of a number of customer owned 2011 model year vehicles with a minimum of 3000 accumulated miles without reprogramming or resetting. To facilitate collection of this data at the dealer level, changes to the GDS have been made so that screen shots will allow the capture of relevant parameters.
*NOTICE
This data collection does not apply to vehicles or dealers operating outside of California.
*NOTICE
IF THE VEHICLE MEETS THE CRITERIA BELOW, CALIFORNIA DEALERS MUST PERFORM THIS DATA COLLECTION ON VEHICLES WHENEVER AN AFFECTED VEHICLE IS IN THE SHOP FOR ANY MAINTENANCE OR REPAIRS.
For vehicles listed on DCS as requiring this procedure, follow the instructions in this bulletin after confirming that the following criteria are met:
^ WebDCS shows this as an open Data Collection code DC002A-B (depending on model) for the vehicle.
^ Vehicle has more than 3000 miles on its odometer.
^ Vehicle repair history does not show battery replacement/disconnection/reset or an ECU Update done in the last 3000 miles, because IUMPR data would have been cleared by such an event.
^ Vehicle does not have a check engine light ON.
CAUTION
If vehicle meets above criteria, collect data prior to any other campaign or repair-related activities.
Service Procedure:
1. Open the engine compartment and locate the emission label under the hood. Locate and write down the "Group" number found on the label for later form entry.
2. To start use the Global Diagnostic System (GDS). Begin by clicking on "ID Register". Click on "Auto VIN" or manually enter vehicle information on the next screen.
*NOTICE
GDS must be updated to version N-K-01-07-0010 or later to properly collect date.
3. Choose "Engine" under "Select System". Click "OK" and follow screen instructions for connecting to vehicle.
4. To verify the VIN, select "Read VIN" under the "Vehicle S/W Management" menu. Click "OK" and write down the VIN for later form entry.
5a. Select "System Identification".
5b. Write down the "Calibration ID" or "ROM ID" number for later form entry. Next go to the main screen by clicking on the "GDS" logo at the top left of the screen.
6. Then select "CARB OBD-II" under the "Diagnosis" tab.
7. Click on "IN-USE Performance Tracking" found in the CARB OBD-II list at the bottom left of the screen. Then click the "Expand" button at the top right corner of "IN-USE Performance Tracking" window.
*NOTICE
If all values indicate "Not Supported" or "0", check to make sure you have GDS software version N-K-01-07-0010 or later. If the software version is correct, and all values show "Not Supported" or "0", the vehicle will not qualify for this data collection, as it may have received a recent ECM Update or battery replacement/reset of the data values.
8. To capture the GDS data, click on the "Capture" button.
*NOTICE
Make sure you capture the entire screen, if only part of the list is displayed, first click "Expand" button, then proceed to capture the entire screen.
9. Select "Scantool Area - Full" and click "Send to file". The GDS will set up a designation folder and file name to save the captured data. Please change the file name to include the model/engine, the last 6 of the VIN and the date (mmddyyyy). Before saving, write down the file name and designation folder for further reference.
Example
10. After saving the file, return to the GDS home page by clicking on "GDS" logo in the upper left hand corner.
11. Then click on the "Feedback" button.
12. Enter all the information requested in the form including your name and email address.
^ For System, enter "Engine".
^ For Subject, enter "Data Collection".
^ In the Description area,
^ Type "Group:" followed by the group number from the Vehicle Emission Control Information label in step 1.
^ Type "Calibration ID:" followed by the calibration ID obtained in step 5b.
^ Add current odometer mileage.
^ Add RO#.
*NOTICE
Please check to ensure both group and Cal ID numbers are correctly entered.
13. To attach the data to the feedback form, click on the "Browse" button.
14. Refer to the file name and destination from step 9.
^ Navigate to: Local Disk (D:) / gvciData / Record /
^ Click on the folder for the vehicle ie., "Sportage (KM)".
^ Click on the folder containing the vehicle VIN.
^ Click on the file name.
^ Once the file name appears in the "File Name" box, click on the "Open" button.
15. When the file name appears in the attachment field and all the information has been entered, click the "Submit" button.
*NOTICE
GDS must be connected to the internet to submit data.
16. Click on the "Close" button to finish.
*NOTICE
You may also print the data prior to submitting as record to attach to the RO.
AFFECTED PRODUCTION RANGE
DATA COLLECTION WARRANTY CLAIM INFORMATION
*NOTICE
VIN inquiry data for this repair is provided for tracking purposes only. Kia retailers should reference DC002 when accessing the WebDCS system.