Emissions - California Emissions Data Extraction

GROUP
Engine

NUMBER
113

MODEL
All 2012 Models

DATE
February 2012

SUBJECT:
DATA COLLECTION: EXTRACT CALIFORNIA EMISSIONS DATA
FROM ECU (DC003)

This bulletin provides information related to extracting "In use performance tracking" emissions data from the engine control unit (ECU) in certain vehicles sold in California. The California Air Resources Board (CARB) requires this emissions data to be extracted from the ECUs of a number of customer owned 2012 model year vehicles with a minimum of 3000 accumulated miles without reprogramming or resetting. To facilitate collection of this data at the dealer level GDS screen shots will allow the capture of relevant parameters.

THIS DATA COLLECTION DOES NOT APPLY TO VEHICLES OR DEALERS OPERATING OUTSIDE OF CALIFORNIA.

*NOTICE

IF THE VEHICLE MEETS THE CRITERIA BELOW, CALIFORNIA DEALERS MUST PERFORM THIS DATA COLLECTION ON VEHICLES WHENEVER AN AFFECTED VEHICLE IS IN THE SHOP FOR ANY MAINTENANCE OR REPAIR.

THIS DATA COLLECTION DOES NOT APPLY TO VEHICLES OR DEALERS OPERATING OUTSIDE OF CALIFORNIA.

For vehicles listed on DOS as requiring this procedure follow the instructions in this bulletin after confirming that the following criteria are met:

^ WebDCS shows this as an open Data Collection code DC003A--->T (depending on model) for the vehicle

*NOTICE

Note that as sufficient data is collected, individual line items per model may be closed without updates to the TSB. Once a line item is closed on DCS, no further data collection is required. Data collections initiated after a line item is closed are subject to chargeback.

^ Vehicle has more than 3000 miles on its odometer.

^ Vehicle repair history does not show battery replacement/disconnection/reset or an ECU Update done in the last 3000 miles, because IUMPR (In Use Monitor Performance Ratio) data would have been cleared by such an event.

^ Vehicle does not have a check engine light ON.

CAUTION

If vehicle meets above criteria, collect data prior to any other campaign or repair-related activities.

Service Procedure:





1. Open the engine compartment and locate the emission label under the hood. Locate and write down the "Group" number found on the label for later form entry.





2. To start use the Global Diagnostic System (GDS). Begin by clicking on "ID Register" Click on "Auto VIN" or manually enter vehicle information on the next screen.





3. Choose "Engine" under "Select System." Click "OK" and follow screen instructions for connecting to vehicle.





4. To verify the VIN select "Read VIN" under the "Vehicle S/W Management" menu. Click "OK" and write down the VIN for later form entry.





5a. Select "System Identification."

5b. Do a screen capture of "Calibration ID" or "ROM ID" number for later form entry.





Select "Scantool Area - Full" and click "Send to file". The GDS will set up a designation folder and file name to save the captured data. Please change the file name to include the model/engine the last 6 of the VIN and the date (mmddyyyy) Before saving write down the file name and designation folder for further reference.

Next, go to the main screen by clicking on the "GDS" logo at the top left of the screen.





6. Then select "CARB OBD-II" under the "Diagnosis" tab.





7. Click on "IN-USE Performance Tracking" found in the CARB OBD-II list at the bottom left of the screen. Then click the "Expand" button at the top right corner of "IN-USE Performance Tracking" window.





8. To capture the GDS data click on the "Capture" button.





9. Select "Scantool Area - Full" and click "Send to file." The GDS will set up a designation folder and file name to save the captured data. Please change the file name to include the model/engine the last 6 of the VIN and the date (mmddyyyy). Before saving write down the file name and designation folder for further reference.





10. After saving the file return to the GDS home page by clicking on "GDS" logo in the upper left hand corner.





11. Then click on the "Feedback" button.





12. Enter all the information requested in the form including your name and email address.

^ For System enter "Engine."

^ For Subject, enter "Data Collection."

^ In the Description area,

^ Type "Group:" followed by the group number from the Vehicle Emission Control Information label in step 1.

^ Type "Calibration ID:" followed by the calibration ID obtained in step 5b

^ Add current odometer mileage.

^ Add RO #





13. To attach the data to the feedback form click on the "Browse" button.





14. Refer to the file name and destination from step 9.

^ Navigate to: Local Disk (D:) / gvciData / Record /

^ Click on the folder for the vehicle i.e., "Sportage (SL)"

^ Click on the folder containing the vehicle VIN

^ Click on the file name.

^ Once the file name appears in the "File Name" box click on the "Open" button. Once file name appears in attachment field repeat and attach screen capture of "Calibration ID" or "ROM ID" number from step 5b.





15. When the file name appears in the attachment field and all the information has been entered click the "Submit" button.

16. Click on the "Close" button to finish





AFFECTED PRODUCTION RANGE:








2012MY DATA COLLECTION WARRANTY CLAIM INFORMATION: