Part 3
Exterior Lighting
Initialization
When the AFS control module receives an engine running signal, the control module performs the initialization procedure which ensures that the headlamps are correctly aligned on their horizontal axis.
The AFS swivel initialization is completed in less than 1 second. The LH and RH AFS motors flick the headlamps to calibrate the centre position of the headlamps.
Failure Mode
In the event of a failure of the AFS system, a warning indicator in the instrument cluster is illuminated to warn the driver. The AFS warning indicator illuminates when the ignition is in accessory power mode 4 or ignition power mode 6 and will flash continuously until the fault is rectified. The AFS warning indicator will also be illuminated if a failure of the steering angle sensor or the vehicle speed signal is detected.
Illumination of the AFS warning indicator does not necessarily mean that there is a fault with the AFS system. The fault may be caused by a failure of another system preventing the AFS system operating correctly.
The AFS control module performs a diagnostic routine every time AFS is requested. If any fault is found, the AFS control module will suspend the operation of the AFS function.
If the AFS system has failed with the xenon projector module in a position other than the correct straight ahead position, the AFS control module will attempt to drive the xenon projector module to the zero (straight ahead) position. If this is not possible, the AFS control module will lower the projector module using the leveling actuator motors to prevent excess glare to oncoming vehicles.
The AFS control module software can detect an internal failure of the control module control circuits. The control module will power the projector modules to the zero position and prevent further operation.
Faults can be investigated by interrogating the AFS control module using an approved Land Rover diagnostic system to check for fault codes.
AUTOMATIC HEADLAMP OPERATION
The automatic headlamp function is a driver assistance system. The driver can override the system operation by selection of side lamp or headlamp on if the ambient light conditions require front and rear lighting to be active. The automatic headlamp system uses a light sensor and the CJB, which are connected via the LIN bus to control the headlamp functionality.
A light sensor is incorporated in the rain/light sensor located on the inside of the windshield, below the rear view mirror. The wiper system also uses the rain/light sensor for automatic wiper operation. For additional information, refer to Wipers and Washers Description and Operation The light sensor measures the ambient light around the vehicle in a vertical direction and also the angular light level from the front of the vehicle. The rain/light sensor uses vehicle speed signals, wiper switch position and the park position of the front wipers to control the system.
The automatic headlamp operation uses ambient light levels which are monitored by photodiode incorporated in the rain/light sensor. The rain/light sensor sends a lights on/off request to the CJB on the LIN bus, which responds by switching on the low beam headlamps, front side lamps and rear tail lamps.
The automatic headlamps are activated under the following conditions:
- Twilight
- Darkness
- Rain
- Snow
- Tunnels
- Underground or multistoried car parks.
Operation of the automatic headlamps requires the ignition to be in ignition mode 6, the lighting control switch to be in the 'AUTO' position and a lights on request signal from the light sensor.
HEADLAMP LEVELING
Headlamp leveling provides for the adjustment of the vertical aim of the headlamps. The leveling system is primarily required to minimize glare to other road users when a heavy load is in the rear of the vehicle.
Two systems of headlamp leveling are available; manual and static.
Manual Headlamp Leveling
Manual headlamp leveling is only available on vehicles with halogen headlamps and coil spring suspension.
The manual system comprises the following components:
- Two headlamp leveling motors
- Headlamp leveling rheostat rotary control.
When the ignition is in ignition mode 6, power is supplied to the lighting control switch via the ignition relay in the battery junction box and to the headlamp leveling motor in each headlamp assembly via the CJB. When the lighting control rotary switch is moved to the side lamp or headlamp position, the supply from the ignition relay is passed to the leveling rotary control.
Movement of the leveling rotary control produces a variable voltage output, which is sensed by the motors. The motors react to the supplied voltage and move the headlamp to the requested position which relates to the supplied voltage from the leveling rotary control.
The headlamps can only be lowered from their unladen position to compensate for changes in vehicle attitude due to loading.
Vehicle Headlamp Leveling
Vehicle headlamp leveling is only available on vehicles with air suspension.
Vehicle headlamp leveling is performed by the air suspension system and the air suspension control module. The suspension system constantly monitors the vehicle attitude and adjusts the height of the front and/or rear of the vehicle accordingly. This maintains the correct vehicle attitude and consequently maintains the correct headlamp beam alignment.
The vehicle leveling system is fully automatic, therefore the lighting control switch does not have the manual leveling rotary control.
HIGH BEAM ASSIST
High beam assist is a driving aid which automatically controls the high beam function. If required, the system can be overridden by the driver.
CAUTION: The high beam assist system is designed as a driving aid only. Should the road conditions require, it is the driver's responsibility to consider other road users and operate the high beam headlamps in a safe manner. In certain circumstances the driver will be required to intervene.
High Beam Assist Warning Indicator
The high beam assist system is controlled by a high beam assist control module which is located in the interior rear view mirror body and by the CJB. The module and the CJB are connected via the medium speed CAN bus.
The high beam assist control module receives a power supply from the CJB when the ignition is in power mode 6 (ignition on). The rear view mirror also includes a low resolution camera (image) sensor which detects headlamps and tail lamps of preceding vehicles. The sensor is connected to the control module which evaluates the image data, checking for light intensity and location.
If conditions are correct, the control module will activate the high beam assist by sending a high or low beam request message to the CJB via the medium speed CAN bus. The CJB then controls the shutter in the Xenon projector module together with the high beam fill-in lamp.
High Beam Assist Operation
The high beam assist operates as part of the automatic headlight system. When driving at night with the lighting control switch in the automatic position and the LH steering column multifunction switch in the central position, with sufficient darkness (approximately 1 lux or less) and a suitable road speed, the high beam assist will automatically operate the high beam lighting when necessary. A warning symbol in the instrument cluster confirms to the driver when the high beam assist system is selected and enabled.
NOTE:
The function of the normal 'blue' high beam indicator remains unchanged and it always reflects the actual status of the high beam lamps
NOTE:
The exterior lighting 'on' threshold for the auto headlamps system is approximately 100 lux which is measured by the rain/light sensor. At light levels below this value the low beam headlamps and exterior lights will be switched on. The high beam assist will not function until the light level has reached approximately 1 lux. At light levels above 1 lux high beam is not required and therefore is not activated.
Activation (system ready)
High beam assist will only activate and illuminate the warning indicator to show system is ready or 'primed' for high beam control, when the following conditions are met:
- High beam assist has been first 'enabled' via the instrument cluster menu
- Lighting control switch is in the 'Auto' position
- LH steering column multifunction switch in the central position
- The ambient light level is below 100 lux - refer to 'Light Levels' section that follows
- The system has not been overridden or cancelled - refer to 'Override' section that follows
- The camera (image) sensor view is not blocked.
High Beam Control
When activated, high beam assist will switch the headlamps to high beam when all the following conditions occur:
- No relevant oncoming traffic
- No relevant preceding traffic
- In non-urban environment, i.e. with no street lighting
- Ambient light level is below 1 lux - refer to 'Light Levels' section that follows
- Road speed is suitable - refer to 'Road Speed' section that follows.
Low Beam Control
When activated, high beam assist will switch the headlamps to low beam when any of the following conditions occur:
- Relevant Oncoming traffic is present
- Relevant Preceding traffic is present
- In urban environment, i.e. with street lighting
- Ambient light level is above 1 lux - refer to 'Light Levels' section that follows
- Road speed is not suitable - refer to 'Road Speed' section that follows
- Unrecognizable reflective inputs from road signs or markings - refer to 'System Limitations' section that follows.
Light Levels
The exterior lighting 'on' threshold for the normal 'auto headlamps' feature is approximately 100 lux and is measured by the windscreen mounted 'rain/light' sensor. When the light level falls to this value the low beam headlamps and exterior lights will be switched on together with the high beam assist warning indicator.
This warns the driver that the system is activated and ready to automatically switch on the high beam headlamps when the light level falls a little further to approximately 1 lux, as measured by the 'ambient light sensor' located in the mirror body. High beam is generally not required with light levels above 1 lux.
Road Speed
A road speed signal is received by the CJB from the Anti-lock Braking System (ABS) module via the high speed CAN bus. When the other activation conditions are correct, the CJB will switch the headlamps to high beam when the road speed has increased above 40 km/h (25 mph).
When the road speed falls to below 24 km/h (15mph), the CJB will switch the headlamps to low beam. The 10 mph (15 km/h) difference between the on and off road speed thresholds prevents the system continually switching between high and low beam at low speeds.
Override
The driver can manually override the high beam assist system at any time. When the high beam assist system is activated, pulling the LH steering column multifunction switch to the high beam 'flash' position or pushing it forward to the high beam position will de-activate the system and the high beam assist warning indicator in the instrument cluster will extinguish.
When the multifunction switch is returned to the central position, from a forward high beam position, the system is re-activated and the high beam assist warning indicator will illuminate again.
Correct Performance
In addition, high beam assist will only exhibit best performance if all of the following conditions are met:
- No false inputs are received by the camera (image) sensor, such as reflected light from certain static signs - refer to 'System Limitations' section that follows
- Headlamps are correctly aligned
- High beam assist system has been set for correct 'hand of traffic' via the driver menu settings - refer to 'Setting Hand of Traffic' section that follows
- Headlamps have been set for correct 'hand of traffic' via the mechanical tourist lever in headlamp casing - refer to 'Setting Hand of Traffic' section that follows
- Camera (image) sensor has been through a self learning 'auto aim' calibration procedure if any components have been replaced - refer to 'Calibration' section that follows
- There are no large reflective items, white papers, etc., sitting on top of the dash board in near view of the camera (image) sensor, or stickers placed directly in front of the camera (image) sensor
Driver Menu Features
The high beam assist feature must first be enabled using the configuration menu available in the instrument cluster. However if required, the high beam assist system can be permanently disabled leaving the basic 'Auto Lamps' system still operative.
Within this menu the system can also be configured for driving on the alternate side of the road (Hand of Traffic). This enables the system to be used in different regions and it's setting is important for correct operation.
Setting 'Hand of Traffic' and High Beam Assist 'Enable'
To set the high beam assist options the following steps must be sequenced:
- With the ignition in power mode 6 (ignition on), and the engine not running, use the controls on the steering wheel to select on the instrument cluster menu:
- Menu > Vehicle Set-up > High Beam Assist
- Configure the 'Hand of Traffic' setting by selecting the appropriate 'Drive on Left' (of road) or 'Drive on Right' (of road) to the applicable Market condition
- Enable the feature by setting 'Activate Assist' if not already selected.
NOTE:
Enabling or disabling high beam assist will not affect the 'Hand of Traffic' settings once set.
NOTE:
The headlamps still require manual adjustment using the tourist lever for driving abroad in countries where the alternate side of the road is used.
The instrument cluster menu also includes a 'High Beam Assist Sensitivity' selection. This is a requirement option for NAS market vehicles only but it is not recommended for normal use and has been superseded.
NOTE:
In other markets the 'Sensitivity' selection is grayed out and cannot be selected.
For additional information, refer to Instrument Cluster Description and Operation
System Limitations
The high beam assist system can occasionally have difficulty distinguishing between light from other vehicles or reflected light from static highly reflective road signs.
These situations may cause the high beam assist system to undesirably operate the high beam headlamps or take no action at all. Examples of these situations are as follows:
- Dips, hollows or crests in the road
- Highly reflective static Road signs
- Tight bends
- Poorly illuminated vehicles e.g. cyclists or small mopeds
- Motorway central barriers
- Extreme weather conditions e.g. Fog, heavy snow
- Exterior domestic or industrial lighting