Fuel Pump Camshaft Timing Check
Fuel Pump Camshaft Timing Check
1 Disconnect the battery ground cable.
For additional information, refer to Specifications Battery, Mounting and Cables
WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands.
2 Raise and support the vehicle.
For additional information, refer to Engine Undershield Engine Undershield
CAUTION: Be prepared to collect escaping oil.
NOTE:
Discard the sealing washer.
NOTE:
Collect the engine oil in a clean container.
CAUTION: Only rotate the crankshaft clockwise.
CAUTION: Make sure that the crankshaft is fully locked.
Install Special Service Tool: Timing Tool, 303-1447
3 Using a suitable marker, mark the position of the crankshaft pulley as illustrated.
NOTE:
Discard the seal.
Remove Special Service Tool:Timing Tool, 303-1447
4 If required, carefully adjust the crankshaft position to allow correct installation of the special tool.
Install Special Service Tool: Alignment Tool, Fuel Pump Camshaft Timing, JLR-303-1613
CAUTION: Do not use excessive force when adjusting the crankshaft position.
NOTE:
If the crankshaft timing tool cannot be installed, adjustment of the fuel pump camshaft timing will be required.
If required, carefully adjust the crankshaft position to allow correct installation of the special tool.
Install Special Service Tool: Timing Tool, 303-1447
If the crankshaft timing tool cannot be installed, adjustment of the fuel pump camshaft timing will be required.
For additional information, refer to Fuel Pump Camshaft Timing Adjustment Fuel Pump Camshaft Timing Adjustment
Remove Special Service Tool:Alignment Tool, Fuel Pump Camshaft Timing, JLR-303-1613
NOTE:
Install a new seal.
Torque to: 12 Nm
Remove Special Service Tool:Timing Tool, 303-1447
Torque to: 10 Nm
NOTE:
Install a new sealing washer.
Torque to: 24 Nm
5 Connect the battery ground cable.
For additional information, refer to Specifications Battery, Mounting and Cables
CAUTION: Make sure that the vehicle is left for 5 minutes from filling with oil and that the engine oil level is reading at least minimum (by following Steps 22-28), before starting the engine.
Fill the engine with oil - for filling values on vehicles without supercharger:
For additional information, refer to Specifications [1][2]Mechanical Specifications
Clean any residual engine oil from the oil filler cap area.
CAUTION: Make sure that the vehicle has been left for 5 minutes from filling with oil.
6 Follow the Steps 22-28 before starting the engine.
Start the engine and allow to run for 10 minutes, stop the engine.
Check for leaks.
CAUTION: Make sure that the selector lever and the gearshift mechanism are in the park (P) position.
CAUTION: Make sure that the hood is open.
Turn the ignition on.
Press the right-hand directional button to access the instrument cluster menu.
Press the right-hand OK button.
Press the right-hand directional button to access the Oil Level Display.
Press the right-hand OK button and follow the instructions.
Press the cruise control cancel button twice within 2 seconds.
The message center display will revert to the normal display in the trip computer.
Press the right-hand OK button and follow the instructions.
Check that the oil level display shows an oil level reading.
Only after having started and run the engine for 10 minutes (as indicated in Step 21), switch off the engine, then stabilizing for 10 minutes, take a reading from the oil level display and, if necessary top up with engine oil.
NOTE:
If instructed to follow Steps 22-28 in a previous step, return to Step 21 and continue the procedure.
7 Turn the ignition off.
8 Allow 10 minutes for the engine oil level to stabilize if there has been additional oil top up.
NOTE:
The following steps are to update the average oil level value.
Turn the ignition on.
Press and hold the cruise control cancel button for more than 2 seconds.
The message center display will revert to the normal display in the trip computer.
9 Turn the ignition off.
10 Turn the ignition on.
Press the right-hand directional button to access the instrument cluster menu.
Press the right-hand OK
button.
Press the right-hand directional button to access the Oil Level Display.
Press the right-hand OK button and follow the instructions.
Make sure that the average oil level value has now been updated.
For additional information, refer to Engine Undershield Engine Undershield
Torque to: 10 Nm