Left Hand Parking Aid Camera Wiring Harness

Left Hand Parking Aid Camera Wiring Harness

Removal

CAUTION: Make sure that the camera overlay wiring harness is not bent excessively during this procedure. Failure to follow this instruction may result in damage to the harness.
1 Remove the LH B-pillar trim panel. For additional information, refer to B-Pillar Trim Panel B-Pillar Trim Panel
2 Remove the LH front seat. For additional information, refer to Front Seat Front Seat




3 Remove the front scuff plate trim panel.
- Release the 7 clips.




4 Remove the B-pillar floor covering trim panel.
- Remove the 2 clips.




5 Remove the parking aid camera module cover.
- Remove the 2 scrivets.




6 Disconnect the camera wiring harness.




7 Remove the LH wiring harness cover.
- Remove the 3 clips.
8 Remove the LH cowl side trim panel. For additional information, refer to Cowl Side Trim Panel Cowl Side Trim Panel




9
NOTE:
Door shown removed for clarity.
NOTE:
Right-hand shown, left-hand similar.
Release the gaiter.





10
NOTE:
Right-hand shown, left-hand similar.
Disconnect the 2 electrical connectors.





11
NOTE:
Right-hand shown, left-hand similar.
Remove the gaiter mounting bracket.
- Carefully release the 6 clips.





12
NOTE:
Right-hand shown, left-hand similar.
Release the electrical connector from the bracket.





13
NOTE:
Some variation in the illustrations may occur, but the essential information is always correct.
Remove the connector from the camera wiring harness.
- Remove the locking tab.
- Carefully release the clip.
- Reposition the camera wiring harness through the A-pillar aperture.

Installation





1
CAUTION: Make sure that the camera overlay wiring harness is not bent excessively during this procedure. Failure to follow this instruction may result in damage to the harness.
Install the camera overlay wiring harness.




2 Connect the camera overlay wiring harness.




3
CAUTION: Make sure that any tie straps used are not tightened excessively on the camera wiring harness and link leads, Failure to follow this instruction may result in damage to the harness.
Carefully wrap any excess camera overlay wiring harness around the module.
- Using suitable tie straps, secure the camera overlay wiring harness to the main body wiring harness.




4
NOTE:
Some variation in the illustrations may occur, but the essential information is always correct.
Remove the connector from the camera overlay wiring harness.
- Remove the locking tab.
- Carefully release the clip.
- Apply suitable tape to protect the end of the camera overlay wiring harness.
5 Feed the camera overlay wiring harness through the A-pillar aperture.




6
NOTE:
Some variation in the illustrations may occur, but the essential information is always correct.
Install the connector to the camera overlay wiring harness.
- Remove the protective tape.
- Install the electrical connector.
- Secure the locking tab.




7 Secure the gaiter to the gaiter bracket.




8
CAUTION: Make sure the electrical connectors are correctly installed and secured.
Secure the camera wiring harness.




9 Connect the 2 electrical connectors.





10 Secure the gaiter mounting bracket.
- Secure the 6 clips.

11 Install the LH cowl side trim panel. For additional information, refer to Cowl Side Trim Panel Cowl Side Trim Panel





12
NOTE:
Left-hand shown, right-hand similar.
Install the LH wiring harness cover.
- Secure the 3 clips.





13 Install the parking aid camera module cover.
- Install the 2 scrivets.





14 Install the B-pillar floor covering trim panel.
- Secure the 2 clips.
- Repeat to the other side.

15 Install the front scuff plate trim panel.
- Secure the 7 clips.

16 Install the LH front seat. For additional information, refer to Front Seat Front Seat

17 Install the LH B-pillar upper trim panel. For additional information, refer to B-Pillar Trim Panel B-Pillar Trim Panel