Right Hand Parking Aid Camera Wiring Harness

Right Hand Parking Aid Camera Wiring Harness

Removal

CAUTION: Make sure that the camera overlay wiring harness is not bent excessively during this procedure. Failure to follow this instruction may result in damage to the harness.
1 Remove the LH B-pillar trim panel. For additional information, refer to B-Pillar Trim Panel B-Pillar Trim Panel
2 Repeat procedure for the other side.




3 Remove the 2 rear bolts from the LH front seat.




4 Release the LH front seat.
- Move the LH front seat fully backwards.
- Remove the 2 front seat front bolts.
5 Remove the RH front seat. For additional information, refer to Front Seat Front Seat




6 With assistance remove the LH front seat.
- Disconnect the 4 electrical connectors.




7
NOTE:
Left-hand shown, right-hand similar.
Remove the front scuff plate trim panel.
- Release the 7 clips.
- Repeat to the other side.




8 Remove the B-pillar floor covering trim panel.
- Remove the 2 clips.
- Repeat to the other side.




9 Remove the parking aid camera module cover.
- Remove the 2 scrivets.
- Repeat to the other side.





10 Disconnect the camera wiring harness.





11 Release the seat heating module bracket.
- Remove the 2 nuts.





12
NOTE:
Left-hand shown, right-hand similar.
Remove the RH wiring harness cover.
- Remove the 3 clips.

13 Remove the cowl side trim panel.For additional information, refer to Cowl Side Trim Panel Cowl Side Trim Panel





14
NOTE:
Door shown removed for clarity.
Release the gaiter.





15 Disconnect the 2 electrical connectors.





16 Remove the gaiter mounting bracket.
- Carefully release the 6 clips.





17 Release the electrical connector from the bracket.





18
NOTE:
Some variation in the illustrations may occur, but the essential information is always correct.
Remove the connector from the camera overlay wiring harness.
- Remove the locking tab.
- Carefully release the clip.
- Reposition the camera wiring harness through the A-pillar aperture.

Installation





1
NOTE:
Some variation in the illustrations may occur, but the essential information is always correct.
Remove the connectors from the camera overlay wiring harness.
- Remove the locking tab.
- Carefully release the clip.
- Apply suitable tape to protect the end of the camera overlay wiring harness.
- Repeat to the other connector.




2
CAUTION: Make sure that the camera overlay wiring harness is not bent excessively during this procedure. Failure to follow this instruction may result in damage to the harness.
Install the camera overlay wiring harness.




3 Insert the camera overlay wiring harness under the floor console.
- Route the camera overlay wiring harness along the main body wiring harness up to the parking aid camera module.




4 Install the connector to the camera overlay wiring harness.
- Remove the protective tape.
- Install the electrical connector.
- Secure the locking tab.




5 Connect the camera overlay wiring harness.




6 Using suitable tie straps, secure the camera overlay wiring harness to the main body wiring harness.
7 Feed the camera overlay wiring harness through the A-pillar aperture.




8
NOTE:
Some variation in the illustrations may occur, but the essential information is always correct.
Install the connector to the camera overlay wiring harness.
- Remove the protective tape.
- Install the electrical connector.
- Secure the locking tab.




9 Secure the gaiter to the gaiter bracket.





10
CAUTION: Make sure the electrical connectors are correctly installed and secured.
Secure the camera wiring harness.





11 Connect the 2 electrical connectors.





12 Secure the gaiter mounting bracket.
- Secure the 6 clips.





13
NOTE:
Left-hand shown, right-hand similar.
Install the RH wiring harness cover.
- Secure the 3 clips.

14 Install the cowl side trim panel. For additional information, refer to Cowl Side Trim Panel Cowl Side Trim Panel





15 Secure the seat heating module bracket.
- Install the 2 nuts.





16 Install the parking aid camera module cover.
- Install the 2 scrivets.





17 Install the B-pillar floor covering trim panel.
- Secure the 2 clips.
- Repeat to the other side.

18 Install the front scuff plate trim panel.
- Secure the 7 clips.
- Repeat to the other side.





19 With assistance, install the LH front seat.
- Connect the 4 electrical connectors.

20 Install the RH front seat. For additional information, refer to Front Seat Front Seat





21
NOTE:
Make sure the 3 seat rail covers are fitted to their original positions. Note: The inner front seat rail does not have a seat rail cover.
Install the 2 front bolts to the front seat.
- Align the front seat locating pegs.
- Position the front seat fully rearwards.
- Tighten the front seat front bolts to 45 Nm.





22
NOTE:
Make sure the 3 seat rail covers are fitted to their original positions. Note: The inner front seat rail does not have a seat rail cover.
Install the 2 rear bolts to the front seat.
- Position the front seat fully forwards.
- Tighten the front seat rear bolts to 45 Nm.

23 Install the LH B-pillar upper trim panel. For additional information, refer to B-Pillar Trim Panel B-Pillar Trim Panel

24 Repeat procedure for the other side.