Floor Console
Floor Console
Removal
1 Disconnect the battery ground cable. For additional information, refer to Specifications Battery and Charging System
2 Remove the LH front seat. For additional information, refer to Front Seat Front Seat
3 Remove the LH floor wiring harness trim panel.
- Remove the 2 clips.
4 Reposition the floor console wiring harness.
- Disconnect the 4 electrical connectors.
- Reposition the carpet for access.
5 Remove the selector lever knob. For additional information, refer to Selector Lever Knob
6 Remove the LH floor console extension. For additional information, refer to Floor Console Extension Floor Console Extension
7 Remove the RH floor console extension.
- Remove the screw.
- Release the 2 clips.
8
NOTE:
Left-hand shown, right-hand similar.
Remove the 2 front bolts from the floor console.
9 Remove the climate controlled seat switch trim panel.
- Carefully release the 4 clips.
- Remove the 2 front screws from the floor console upper panel.
10 Remove the rear floor register.
- Release the 4 clips.
11
NOTE:
Left-hand shown, right-hand similar.
Remove the 2 rear bolts from the floor console.
- Remove the floor console rear LH floor register.
- Remove the floor console rear LH bolt.
- Remove the floor console rear RH floor register.
- Remove the floor console rear RH bolt.
12 Remove the floor console.
- Reposition the floor console upwards and rearwards.
13 Remove the auxiliary climate control rear register. For additional information, refer to Register Register
14 Remove the cellular phone cradle assembly lower trim panel.
- Reposition the cellular phone cradle assembly.
- Remove the 6 screws.
15 Remove the cellular phone cradle assembly.
- Disconnect the 2 electrical connectors.
- Release the 2 electrical connectors from the clips.
16 Remove the floor console stowage compartment.
- Open the floor console stowage compartment lid.
- Remove the 2 screws.
- Carefully release the 2 clips.
- Disconnect the cigar lighter electrical connector.
17
CAUTION: Make sure damage does not occur to the vehicle trim when removing the centre console side finisher trim panel.
NOTE:
Left-hand shown, right-hand similar.
Remove the center console LH side finisher trim panel.
- Using a suitable tool, carefully release the 3 clips.
18
CAUTION: Make sure damage does not occur to the vehicle trim when removing the centre console side finisher trim panel.
Remove the center console RH side finisher trim panel.
- Using a suitable tool, carefully release the 3 clips.
19 Reposition the floor console upper panel.
- Remove the 4 screws.
- Using a suitable tool, carefully release the 4 clips.
20 Disconnect the parking brake switch electrical connector.
21 Remove the floor console upper panel.
- Release the 3 wiring harness clips.
- Disconnect the 3 electrical connectors.
22 Disconnect the 6 electrical connectors from the rear passenger entertainment control panel.
23
NOTE:
Do not disassemble further if the component is removed for access only.
Remove the floor console rear trim panel.
- Remove the 4 screws.
24 Remove the rear auxiliary climate control assembly.
- Remove the 4 screws.
- Disconnect the 2 electrical connectors.
25
NOTE:
Left-hand shown, right-hand similar.
Remove the floor console LH finisher trim panel.
- Remove the 11 screws.
26 Remove the floor console RH finisher trim panel.
- Remove the 11 screws.
27 Remove the 14 clips from the floor console.
28 Remove the 2 brackets from the floor console.
- Remove the 2 screws.
Installation
1 Install the 2 brackets to the floor console.
- Install the 2 screws.
2 Install the 14 clips to the floor console.
3 Install the floor console LH finisher trim panel.
- Install the 10 screws.
4 Install the floor console RH finisher trim panel.
- Install the 10 screws.
5 Install the rear auxiliary climate control assembly.
- Connect the 2 electrical connectors.
- Install the 4 screws.
6 Install the floor console rear trim panel.
- Install the 4 screws.
7 Connect the 6 electrical connectors to the rear passenger entertainment control panel.
8 Install the floor console upper panel.
- Connect the 3 electrical connectors.
- Attach the 3 wiring harness clips.
9 Connect the parking brake switch electrical connector.
10 Reposition the floor console upper panel.
- Secure the 4 clips.
- Install the 4 screws.
11 Install the center console LH side finisher trim panel.
- Secure the 3 clips.
12 Install the center console RH side finisher trim panel.
- Secure the 3 clips.
13 Install the floor console stowage compartment.
- Connect the cigar lighter electrical connector.
- Secure the 2 clips.
- Install the 2 screws.
- Close the floor console stowage compartment lid.
14 Install the cellular phone cradle assembly.
- Attach the 2 electrical connectors to the clips.
- Connect the 2 electrical connectors.
15 Install the cellular phone cradle assembly lower trim panel.
- Install the six screws.
- Reposition the cellular phone cradle assembly.
16 Install the auxiliary climate control rear register. For additional information, refer to Register Register
17
CAUTION: Make sure the floor console is correctly located and installed. Failure to follow this instruction will result in damage to the vehicle trim.
Install the floor console.
- Reposition the floor console to its original position.
18 Install the 2 rear bolts to the floor console.
- Install the floor console rear RH bolt.
- Install the floor console rear RH floor register.
- Install the floor console rear LH bolt.
- Install the floor console rear LH floor register.
19 Install the rear floor register.
- Secure the 4 clips.
20 Install the climate controlled seat switch trim panel.
- Install the 2 front screws to the floor console upper panel.
- Secure the 4 clips.
21 Install the 2 front bolts to the floor console.
- Install the floor console front RH bolt.
- Install the floor console front LH bolt.
22 Install the LH floor console extension. For additional information, refer to Floor Console Extension Floor Console Extension
23 Install the RH floor console extension.
- Install the screw.
- Secure the 2 clips.
24 Install the selector lever knob. For additional information, refer to Selector Lever Knob
25 Reposition the floor console wiring harness.
- Reposition the carpet for access.
- Connect the 4 electrical connectors.
26 Install the LH floor wiring harness trim panel.
- Install the 2 clips.
27 Install the LH front seat. For additional information, refer to Front Seat Front Seat
28 Connect the battery ground cable. For additional information, refer to Specifications Battery and Charging System