Front Seat Cushion Cover

Front Seat Cushion Cover

Removal

WARNING: Persons working on the supplemental restraint system (SRS) must be fully trained and have been issued with the safety guidelines.

WARNING: Allow a period of 10 minutes to elapse after disconnecting the battery before undertaking any work on the SRS.

WARNING: The SRS electrical connectors are unique. DO NOT force, or attempt to connect electrical connectors to the wrong sockets.

WARNING: The correct procedures must always be used when working on SRS components.

WARNING: It is imperative that before any work is undertaken on the SRS system, the appropriate information is read thoroughly.

WARNING: Always disconnect both battery cables before beginning work on the SRS system. Disconnect the ground cable first. Never reverse connect the battery.

WARNING: Take extra care when handling SRS components.

CAUTION: The front passenger seat occupant classification sensor is available only as a service kit. No attempt should be made to replace individual components. Failure to follow this instruction may result in personal injury.
1 Disconnect the battery ground cable. For additional information, refer to Specifications Battery and Charging System
2 Make the air bag supplemental restraint system (SRS) safe. For additional information, refer to Standard Workshop Practices
3 Remove the front seat. For additional information, refer to Front Seat Front Seat




4 Release the 2 lower tension straps from the front seat base.
- Reposition the front seat backrest cover for access.




5 Remove the front seat side trim panel support.
- Release the 2 clips.
6 Remove the seat control switch. For additional information, refer to Seat Control Switch Seat Control Switch




7 Remove the front seat base side trim panel mounting bracket.
- Release the 2 wiring harness clips.
- Remove the 4 screws.




8 Remove the front seat backrest hinge cover.
- Remove the 2 screws.
- Release the clip.




9
NOTE:
Left-hand shown, right-hand similar.
Remove the 2 clips from the front seat backrest cover lower trim panel.





10 Remove the front seat backrest cover lower trim panel.
- Release the front seat backrest cover lower trim panel from the 2 clips.





11
WARNING: The front seat base has sharp edges, hand protection must be worn when releasing the front seat cushion cover from the front seat base. Failure to follow this instruction may result in personal injury.
Release the front seat cushion cover from the rear of the front seat base.





12
WARNING: The front seat base has sharp edges, hand protection must be worn when releasing the front seat cushion cover from the front seat base. Failure to follow this instruction may result in personal injury.
NOTE:
Left-hand shown, right-hand similar.
Release the front seat cushion cover from the left-hand side of the front seat base.

13
WARNING: The front seat base has sharp edges, hand protection must be worn when releasing the front seat cushion cover from the front seat base. Failure to follow this instruction may result in personal injury.
Release the front seat cushion cover from the right-hand side of the front seat base.





14
WARNING: The front seat base has sharp edges, hand protection must be worn when releasing the front seat cushion cover from the front seat base. Failure to follow this instruction may result in personal injury.
Remove the front seat cushion and front seat cushion cover from the front seat base.
- Reposition the front seat for access.
- Release the front seat cushion cover from the front of the front seat base.





15
NOTE:
Do not disassemble further if the component is removed for access only.
Release the front seat cushion cover tension strap.





16 Remove and discard the 15 clips from the front seat cushion cover.
- Reposition the front seat cushion cover for access.





17 Remove the front seat cushion cover from the front seat cushion.

Installation
1 Install the front seat cushion cover to the front seat cushion.
2 Install the 15 new clips to the front seat cushion cover.
- Reposition the front seat cushion cover to the front seat cushion.
3 Secure the front seat cushion cover tension strap.
4
WARNING: The front seat base has sharp edges, hand protection must be worn when securing the front seat cushion cover to front seat base. Failure to follow this instruction may result in personal injury.
Install the front seat cushion and cover to the front seat base.
- Reposition the front seat for access.
- Secure the front seat cushion cover to the front of the front seat base.
5
WARNING: The front seat base has sharp edges, hand protection must be worn when securing the front seat cushion cover to front seat base. Failure to follow this instruction may result in personal injury.
Secure the front seat cushion cover to the right-hand side of the front seat base.
6
WARNING: The front seat base has sharp edges, hand protection must be worn when securing the front seat cushion cover to front seat base. Failure to follow this instruction may result in personal injury.
Secure the front seat cushion cover to the left-hand side of the front seat base.
7
WARNING: The front seat base has sharp edges, hand protection must be worn when securing the front seat cushion cover to front seat base. Failure to follow this instruction may result in personal injury.
Secure the front seat cushion cover to the rear of the front seat base.
8 Install the front seat backrest cover lower trim panel.
- Secure the front seat backrest cover lower trim panel to the 2 clips.
9 Install the 2 clips to the front seat backrest cover lower trim panel.

10 Install the front seat backrest hinge cover.
- Secure the clip.
- Install the 2 screws.

11 Install the front seat base side trim panel mounting bracket.
- Install the 4 screws.
- Secure the 2 wiring harness clips.

12 Install the seat control switch. For additional information, refer to Seat Control Switch Seat Control Switch

13 Install the front seat side trim panel support.
- Secure the 2 clips.

14 Secure the 2 lower tension straps to the front seat base.
- Reposition the front seat backrest cover.

15 Install the front seat. For additional information, refer to Front Seat Front Seat

16 Connect the battery ground cable. For additional information, refer to Specifications Battery and Charging System

17 Using the Land Rover approved diagnostic system, calibrate the occupant classification sensor.