Component Tests and General Diagnostics

INSPECT FRONT WIPER AND WASHER SWITCH CONTINUITY
If continuity is not as specified, replace the switch.







INSPECT FRONT WIPER AND WASHER SWITCH CIRCUIT
Connector disconnected:
Disconnect the connector from the motor and inspect the connector on the wire harness side.
If circuit is not as specified, inspect the circuits connected to other parts.

INSPECT FRONT WIPER INTERMITTENT OPERATION
a. Turn the wiper switch to INT position.
b. Turn the intermittent time control switch to FAST position.




c. Connect the positive (+) lead from the battery to terminal 16 and the negative (-) lead to terminal 2.
d. Connect the positive (+) lead from the voltmeter to terminal 7 and the negative (-) lead to terminal 2, check that the meter needle indicates battery voltage.







e. After connecting terminal 16 to terminal 17, connect to terminal 2 to terminal 17, check the voltage rises from 0 Volts to battery voltage with in the times, as shown in the table.
If operation is not as specified, replace the wiper and washer switch.







INSPECT REAR WIPER AND WASHER SWITCH CONTINUITY
If continuity is not as specified, replace the switch.







INSPECT REAR WIPER AND WASHER SWITCH CIRCUIT
Disconnect the connector from the motor and inspect the connector on the wire harness side.
If circuit is not as specified, inspect the circuits connected to other parts.




INSPECT FRONT WIPER MOTOR OPERATION
Low Speed:
Connect the positive (+) lead from the battery to terminal 1 and the negative (-) lead to terminal 5, check that the motor operates at low speed.
If operation is not as specified, replace the motor.




INSPECT FRONT WIPER MOTOR OPERATION
High Speed:
Connect the positive (+) lead from the battery to terminal 4 and the negative (-) lead to terminal 5, check that the motor operates at high speed.
If operation is not as specified, replace the motor.

INSPECT FRONT WIPER MOTOR OPERATION
Stopping at Stop Position:




a. Operate the motor at low speed and stop the motor operation anywhere except at the stop position by disconnecting positive (+) lead from terminal 1.




b. Connect terminals 1 and 3.
c. Connect the positive (+) lead from the battery to terminal 2 and negative (-) lead to terminal 5, check that the motor stops running at the stop position after the motor operates again.
If operation is not as specified, replace the motor.







INSPECT FRONT WIPER MOTOR CIRCUIT
Connector disconnected:
Disconnect the connector from the motor and inspect the connector on the wire harness side.
It circuit is not as specified, inspect the circuits connected to other parts.




INSPECT REAR WIPER MOTOR OPERATION
Low Speed:
Connect the positive (+) lead from the battery to terminal 3 and negative (-) lead to terminal 2, check that the motor operates at low speed.
If operation is not as specified, replace the motor

INSPECT REAR WIPER MOTOR OPERATION
Stopping at Stop Position:




a. Operate the motor at low speed and stop the motor operation anywhere except at the stop position by disconnecting positive (+) lead from terminal 3.




b. Connect terminals 3 and 4.
c. Connect the positive (+) lead from the battery to terminal 1 and negative (-) lead to terminal 2, check that the motor stops running at the stop position after the motor operates again.
If operation is not as specified, replace the motor.

Terminal Identification:

INSPECT REAR WIPER MOTOR CIRCUIT
Connector disconnected:
Disconnect the connector from the motor and inspect the con nector on the wire harness side.
If circuit is not as specified, inspect the circuits connected to other parts.




INSPECT FRONT WASHER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, check that the motor operates.

NOTE: These tests must be performed quickly (within 20 seconds) to prevent the coil from burning out.
If operation is not as specified, replace the motor.







INSPECT FRONT WASHER MOTOR CIRCUIT
Connector disconnected:
Disconnect the connector from the motor and inspect the connector on the wire harness side.
If circuit is not as specified, inspect the power source and wire harness.




INSPECT REAR WASHER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, check that the motor operates.

NOTE: These tests must be performed quickly (within 20 seconds) to prevent the coil from burning out.
If operation is not as specified, replace the motor.







INSPECT REAR WASHER MOTOR CIRCUIT
Connector disconnected:
Disconnect the connector from the motor and inspect the connector on the wire harness side.
If circuit is not as specified, inspect the power source, wire harness and wiper switch.







INSPECT REAR WIPER RELAY CONTINUITY
If continuity is not as specified, replace the relay.

INSPECT REAR WIPER RELAY OPERATION

INSPECT REAR WIPER RELAY INTERMITTENT OPERATION