Front Seat
DISASSEMBLY1. REMOVE HEADREST
2. REMOVE FRONT SEAT CUSHION SHIELD
a. Remove the power seat switch knobs.
b. Remove the 4 screws and front seat cushion shield, then disconnect the connector.
3. REMOVE FRONT SEAT INNER CUSHION COVER
Remove the 3 screws and front seat inner cushion cover.
4. REMOVE NO. 1 FRONT SEAT CUSHION SHIELD
Remove the 2 screws and No. 1 front seat cushion shield.
5. REMOVE SEAT CUSHION ASSEMBLY
a. Remove the wire harness from the seat cushion assembly.
b. Remove the 4 bolts and seat cushion assembly.
6. REMOVE SEAT CUSHION COVER
a. Remove the hog rings.
b. Disengage the seat cushion cover hook.
c. Remove the seat cushion cover with pad.
d. Remove the hog rings and seat cushion cover from the pad.
7. REMOVE SEATBACK ASSEMBLY
a. Remove the seatback board as shown in the illustration.
b. Remove the hog rings.
c. Remove the 4 seatback assembly set bolts.
NOTE: Be careful not to pull the side airbag assembly wire harness.
d. Remove the 6 screws and seat cushion inside covers, then disconnect the wire harness from the covers.
e. Disengage the wire harness clamps.
f. Remove the seatback assembly.
8. REMOVE SEATBACK COVER
a. Remove the hog rings.
b. Remove the 2 screws and disengage the seat cover hook and retainer from the seatback frame.
c. Remove the headrest supports.
d. Remove the cap, bolt, washer, wave washer and armrest.
e. Remove the seatback frame from the seatback cover with pad.
f. Driver's Seat:
Remove the 2 bolts and lumber support assembly from the seatback frame.
g. Remove the hog rings and seatback cover from the seat-back pad.
9. REMOVE FRONT SEAT INNER BELT
Remove the bolt and front seat inner belt.
10. REMOVE WIRE HARNESS
Disconnect the connectors, then remove the wire harness.
11. Driver's Seat:
REMOVE SEAT POSITION CONTROL RELAY
Remove the 2 nuts and seat position control relay.
12. REMOVE SLIDE MOTOR
a. Remove the 2 screws.
b. Disconnect the seat adjuster drive cable, then remove the slide motor.
13. REMOVE FRONT VERTICAL MOTOR
Remove the 2 screws and front vertical motor.
14. REMOVE LIFTER MOTOR
Remove the 2 screws and rear lifter motor.
15. REMOVE RECLINING MOTOR
a. Remove the 2 screws.
b. Disconnect the shaft, then remove the reclining motor.
16. REMOVE POWER SEAT SWITCH
Remove the 2 screws and power seat switch.
REASSEMBLY
1. INSTALL POWER SEAT SWITCH
Install the power seat switch with the 2 screws.
2. INSTALL RECLINING MOTOR
Connect the shaft, then install the reclining motor with the 2 screws.
3. INSTALL LIFTER MOTOR
Install the lifter motor with the 2 screws.
4. INSTALL FRONT VERTICAL MOTOR
Install the front vertical motor with the 2 screws.
5. INSTALL SLIDE MOTOR
Connect the seat adjuster drive cable, then install the slide motor with the 2 screws.
6. Driver's Seat:
INSTALL SEAT POSITION CONTROL RELAY
Install the seat position control relay with the 2 nuts.
7. INSTAL WIRE HARNESS
Connect the connectors, then install the wire harness to the seat adjuster.
8. INSTALL FRONT SEAT INNER BELT
Install the front seat inner belt with the bolt.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
9. INSTALL SEATBACK COVER
a. Install the seatback cover with the new hog rings to the seatback pad.
b. Driver's Seat:
Install the lumber support assembly with the 2 bolts to the seatback frame.
c. Install the seatback cover with pad to the seatback frame with the new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
d. Install the armrest, wave washer and washer with the bolt then install the cap.
e. Install the headrest supports.
f. Engage the seat cover hook and retainer, then install the 2 screws to the seatback frame.
g. Install the new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
10. INSTALL SEATBACK ASSEMBLY
a. Mount the seatback assembly on the seat adjuster assembly.
b. Connect the lumber support assembly connector.
c. Install the wire harness to the seat cushion inside covers as shown in the illustration.
NOTE: Be careful not to damage the wire harness.
d. Install the seat cushion inside covers with the 6 screws.
e. Install the 4 seatback assembly set bolts.
Torque: 37 N.m (377 kgf.cm, 27 ft.lbf)
f. Engage the wire harness clamps. Install the new hog rings.
g. Install the new hog ring.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
h. Install the seatback board as shown in the illustration.
11. INSTALL SEAT CUSHION COVER
a. Install the seat cushion cover with new hog rings to the seat cushion pad.
b. Install the seat cushion cover with pad to the seat cushion frame.
c. Engage the seat cushion cover hook.
d. Install new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
12. INSTALL SEAT CUSHION ASSEMBLY
a. Install the seat cushion assembly with the 4 bolts to the seat adjuster.
Torque: 18 N.m (183 kgf.cm, 13 ft.lbf)
b. Install the wire harness to the seat cushion as shown in the illustration.
13. INSTALL NO. 1 FRONT SEAT CUSHION SHIELD
Install the No. 1 front seat cushion shield with the 2 screws.
14. INSTALL FRONT SEAT INNER CUSHION COVER
Install the front seat inner cushion cover with the 3 screws.
15. INSTALL FRONT SEAT CUSHION SHIELD
a. Connect the connector, then install the front seat cushion shield with the 4 screws.
b. Install the power seat switch knobs.
16. INSTALL HEADREST