Rear
REMOVAL1. REMOVE REAR WHEEL
Torque: 103 Nm (1,050 kgf-cm, 76 ft. lbs.)
2. CHECK BEARING BACKLASH AND AXLE HUB DEVIATION
a. Remove the 2 bolts, brake caliper and disc.
b. Support the brake caliper securely.
c. Using a dial indicator, check the backlash near the center of the axle hub.
Maximum: 0.05 mm (0.0020 inch)
If the backlash exceeds the maximum, replace the bearing.
d. Using a dial indicator, check the deviation at the surface of the axle hub outside the hub bolt.
Maximum: 0.05 mm (0.0020 inch)
If the deviation exceeds the maximum, replace the bearing.
e. Install the disc, brake caliper and 2 bolts.
Torque: 47 Nm (475 kgf-cm, 34 ft. lbs.)
3. REMOVE DRIVE SHAFT LOCK NUT
a. Remove the cotter pin and lock cap.
b. While applying the brakes, remove the nut.
Torque: 216 Nm (2,200 kgf-cm, 159 ft. lbs.)
c. Remove the 2 bolts, brake caliper and disc.
Torque: 47 Nm (475 kgf-cm, 34 ft. lbs.)
d. Support the brake caliper securely.
4. REMOVE ABS SPEED SENSOR
Remove the bolt and ABS speed sensor from the axle carrier.
Torque: 20 Nm (200 kgf-cm, 14 ft. lbs.)
5. DISASSEMBLE PARKING BRAKE ASSEMBLY
6. DISCONNECT PARKING BRAKE CABLE
Remove the 2 bolts and disconnect parking brake cable from the backing plate.
Torque: 8.0 Nm (82 kgf-cm, 71 inch lbs.)
7. LOOSEN 2 BOLTS ON LOWER SIDE OF SHOCK ABSORBER
HINT: Do not remove the 2 bolts and nuts.
Torque: 255 Nm (2,600 kgf-cm, 188 ft. lbs.)
8. DISCONNECT STRUT ROD
a. Remove the strut rod rear bolt and nut.
Torque: 123 Nm (1,250 kgf-cm, 91 ft. lbs.)
HINT: At the time of installation, after stabilizing the suspension, torque the bolt.
b. Disconnect the strut rod from the axle carrier.
9. DISCONNECT NO. I LOWER SUSPENSION ARM
a. Remove the No. 1 lower suspension arm set bolt and nut from the axle carrier.
Toque: 177 Nm (1,800 kgf-cm, 131 ft. lbs.)
HINT: At the time of installation, after stabilizing the suspension, torque the bolt.
b. Disconnect the No. 1 lower suspension arm from the axle carrier.
10. DISCONNECT NO. 2 LOWER SUSPENSION ARM
a. Remove the No. 2 lower suspension arm set bolt and nut from the axle carrier.
Torque: 177 Nm (1,800 kgf-cm, 131 ft. lbs.)
HINT: At the time of installation, after stabilizing the suspension, torque the bolt.
b. Disconnect the No.2 lower suspension arm from the axle carrier.
11. REMOVE REAR AXLE HUB WITH CARRIER
a. Remove the 2 nuts and bolts on the lower side of the shock absorber.
b. Remove the axle carrier with the axle hub.
NOTICE: Be careful not to damage the boot, oil seal and ABS speed sensor rotor.
DISASSEMBLY
1. REMOVE AXLE HUB AND INNER RACE (INSIDE)
a. Using SST, remove the axle hub from the axle carrier.
SST 09520-00031
b. Remove the inner race (inside).
c. Using SST, and a press, remove the inner race (outside) from the axle hub.
SST 09555-55010,09950-60010 (09951-00360), 09950-70010 (09951-07100)
2. REMOVE BACKING PLATE
Remove the 4 nuts and backing plate.
3. REMOVE INNER AND OUTER OIL SEALS
Using SST, remove the inner and outer oil seals.
SST 09308-00010
4. REMOVE SNAP RING AM
Using snap ring pliers, remove the snap ring.
5. REMOVE BEARING FROM REAR AXLE CARRIER
a. Place the inner race on the inside of the bearing.
b. Using SST and a press, remove the bearing from the axle carrier.
SST 09310-35010
REASSEMBLY
1. INSTALL BEARING
Using SST and a press, install the bearing to the axle carrier.
SST 09527-17011, 09950-60020 (09951-00710), 09950-70010 (09951-07100)
NOTICE: If the inner race and balls become loose and come out from the bearing outer race, make sure to install them on the same side as before.
2. INSTALL SNAP RING
Using snap ring pliers, install a new snap ring.
3. INSTALL OUTER OIL SEAL
a. Using SST and a hammer, install a new outer oil seal.
SST 09608-32010, 09950-70010 (09951-07100)
b. Coat VIP grease to the oil seal lip.
4. INSTALL BACKING PLATE Install the backing plate with the 4 nuts.
Torque: 72 Nm (730 kgf-cm, 53 ft. lbs.)
5. INSTALL AXLE HUB
Using SST and a press, install the axle hub.
SST 09950-60020 (09951-00730), 09950-70010 (09951-07100)
NOTICE: Be careful not to damage the bearing.
6. INSTALL INNER OIL SEAL
a. Using SST and a hammer, install a new inner oil seal.
SST 09316-60011 (09316-00011, 09316-00031), 09502-12010
b. Coat MP grease to the oil seal lip.
INSTALLATION
Installation is in the reverse order of removal. AFTER INSTALLATION, CHECK ABS SPEED SENSOR SIGNAL REAR WHEEL ALIGNMENT