Front Seat

DISASSEMBLY

1. REMOVE HEADREST




2. REMOVE SEATBACK BOARD
Remove the seatback board as shown in the illustration.

HINT: Remove the seatback board in the order of "A" and "B" as shown in the illustration.

3. REMOVE SEAT CUSHION OUTER SHIELD
a. Using a screwdriver, remove the power seat switch knobs.

HINT: Tape up the screwdriver tip before use.




b. Remove the 4 screws.
c. Disconnect the connectors as shown in the illustration.
d. Remove the seat cushion outer shield.




e. Remove the 3 screws and the power seat switch from the seat cushion outer shield.
f. Remove the 2 screws and the lumbar support switch from the seat cushion outer shield.

4. REMOVE FRONT SEAT INNER BELT




a. Remove the clamp, then disconnect the connector.
b. Remove the bolt and the inner belt.




5. REMOVE SEAT CUSHION INNER SHIELD
Remove the 3 screws and the seat cushion inner shield.




6. REMOVE LOWER SEAT CUSHION SHIELD
Remove the screw and the lower seat cushion shield as shown in the illustration.




7. REMOVE FRONT SEAT CUSHION SHIELD
Remove the screw and the front seat cushion shield.

8. REMOVE SEAT CUSHION ASSEMBLY




a. Remove the 4 bolts.
b. Remove the clamps from the seat cushion assembly.

9. REMOVE SEAT CUSHION FRAME
a. Disengage the hook.
b. Remove the hog rings and the seat cushion frame from the seat cushion cover with pad.

10. REMOVE SEAT CUSHION COVER
11. IF NECESSARY, REPLACE SEAT CUSHION HEATER
12. REMOVE SEATBACK ASSEMBLY




a. Remove the hog rings.
b. Disengage the hook as shown in the illustration.
c. Disconnect the connectors.




d. Remove the 4 bolts and the seatback assembly.

NOTE: When handling the airbag connector, take care not to damage the airbag wire harness.

e. Remove the screw and the RH reclining adjuster inside shield.
f. Disconnect the side airbag connector.

NOTE: When handling the airbag connector, take care not to damage the airbag wire harness.

g. Remove the screw and the LH reclining adjuster inside shield.

13. REMOVE ARMREST
14. REMOVE SEATBACK FRAME




a. Remove the hog rings, the clamps and the 2 bolts.
b. Remove the 2 headrest supports.
c. Remove the seatback frame from the seatback cover with the pad.




15. REMOVE LUMBAR SUPPORT
Remove the 2 bolts, the lumbar support and the spacer.

16. REMOVE POWER SEAT MOTOR ASSEMBLY
Remove the 4 screws and the power seat motor assembly.




17. REMOVE SEATBACK COVER
Remove the hog rings and the seatback cover from the seatback pad.

18. IF NECESSARY, REPLACE SEATBACK HEATER
19. REMOVE SEAT POSITION CONTROL RELAY
a. Disconnect the connectors.
b. Remove the 2 bolts and the seat position control relay.




20. Driver's Side:
REMOVE SEAT POSITION SENSOR
Remove the bolt and the seat position sensor, then disconnect the connector.

REASSEMBLY




1. Driver's Side:
INSTALL SEAT POSITION SENSOR
Install the seat position sensor with a new bolt, then connect the connector.

Part No.:
Bolt: 90119-06871

Torque: 8.0 N.m (82 kgf.cm, 71 in.lbf)

2. INSTALL SEAT POSITION CONTROL RELAY
Install the 2 bolts and the seat position control relay, then connect the connectors.

Torque: 5.5 N.m (56 kgf.cm, 49 in.lbf)




3. INSTALL SEATBACK COVER
Install the seatback cover to the seatback pad with new hog rings.

4. INSTALL POWER SEAT MOTOR ASSEMBLY
Install the power seat motor assembly with the 4 screws.




5. INSTALL LUMBAR SUPPORT
Install the lumbar support and the spacer with the 2 bolts.

6. INSTALL SEATBACK FRAME




a. Install the seatback cover to the seatback frame.
b. Install new hog rings the clamps, and the 2 bolts.

Torque: 4.7 N.m (48 kgf.cm, 42 in.lbf)

c. Install the 2 headrest supports.

7. INSTALL SEATBACK ASSEMBLY




a. Place the airbag connector along the inner seat adjuster, and then install the RH reclining adjuster inside shield with the screw so that the connector is placed in between.

NOTE: When handling the airbag connector, take care not to damage the airbag wire harness.

b. Install the LH reclining adjuster inside shield with the screw.




c. Install the seatback assembly with the 4 bolts.

Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)

d. Install new hog rings.




e. Hang the hook.
f. Connect the connectors.

8. INSTALL ARMREST

Torque: 37 N.m (380 kgf.cm, 27 ft.lbf)

9. INSTALL HEADREST
10. INSTALL SEAT CUSHION COVER
11. INSTALL SEAT CUSHION FRAME
a. Install the seat cushion frame with new hog rings to the seat cushion cover with pad.
b. Hang the hook.

12. INSTALL SEAT CUSHION ASSEMBLY




a. Install the seat cushion assembly with the 4 bolts to the seat adjuster.

Torque: 21 N.m (210 kgf.cm, 15 ft.lbf)

b. Engage the wire harness clamp.




13. INSTALL FRONT SEAT CUSHION SHIELD
Install the seat cushion shield with the screw.




14. INSTALL LOWER SEAT CUSHION SHIELD
Install the seat cushion shield with the screw.




15. INSTALL SEAT CUSHION INNER SHIELD
Install the seat cushion inner shield with the 3 screws.

16. INSTALL FRONT SEAT INNER BELT




a. Engage the clamp, then connect the connector.
b. Install the inner belt with the bolt.

Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)

17. INSTALL SEAT CUSHION OUTER SHIELD
a. Install the power seat switch with the 3 screws.
b. Install the lumbar support switch with the 2 screws.
c. Connect the connectors as shown in the illustration.




d. Install the seat cushion outer shield with the 4 screws.
e. Install the power seat switch knobs.

18. INSTALL SEATBACK BOARD