Front Seat
DISASSEMBLY1. REMOVE HEADREST
2. REMOVE FRONT SEAT CUSHION SHIELD
a. Remove the power seat switch knobs.
b. Remove the 4 screws and front seat cushion shield, then disconnect the connector.
3. REMOVE FRONT SEAT INNER CUSHION COVER
Remove the 3 screws and front seat inner cushion cover.
4. REMOVE NO. 1 FRONT SEAT CUSHION SHIELD
Remove the 2 screws and No. 1 front seat cushion shield.
5. REMOVE SEAT CUSHION ASSEMBLY
a. Remove the wire harness from the seat cushion assembly.
b. Remove the 4 bolts and seat cushion assembly.
6. REMOVE SEAT CUSHION COVER
a. Remove the hog rings.
b. Disengage the seat cushion cover hook.
c. Remove the seat cushion cover with pad.
d. Remove the hog rings and seat cushion cover from the pad.
7. w/ Seat heater:
IF NECESSARY, REPLACE SEAT CUSHION HEATER
8. REMOVE SEATBACK ASSEMBLY
a. Remove the seatback board as shown in the illustration.
b. Remove the hog rings.
c. Remove the 4 seatback assembly set bolts.
NOTE: Be careful not to pull the side airbag assembly wire harness.
d. Remove the 6 screws and seat cushion inside covers, then disconnect the wire harness from the covers.
e. Disengage the wire harness clamps.
f. Remove the seatback assembly.
9. REMOVE SEATBACK COVER
a. Remove the hog rings.
b. Remove the 2 screws and disengage the seat cover hook and retainer from the seatback frame.
c. Remove the headrest supports.
d. Remove the cap, bolt, washer, wave washer and armrest.
e. Remove the seatback frame from the seatback cover with pad.
f. Driver's seat: Remove the 2 bolts and lumber support assembly from the seatback frame.
g. Remove the hog rings and seatback cover from the seat-back pad.
10. w/ Seat heater:
IF NECESSARY, REPLACE SEATBACK HEATER
11. REMOVE FRONT SEAT INNER BELT
Remove the bolt and front seat inner belt.
12. REMOVE POWER SEAT SWITCH
Remove the 2 screws and power seat switch.
13. REMOVE WIRE HARNESS
Disconnect the connectors, then remove the wire harness.
14. Driver's seat:
REMOVE SEAT POSITION CONTROL RELAY
Remove the 2 nuts and seat position control relay.
15. Driver's seat:
REMOVE TORSION BAR
Using a screwdriver, remove the torsion bar.
16. REMOVE SEAT TRACK COVERS AND BELT ANCHOR BRACKET
a. Using a screwdriver, remove the 2 seat track covers.
b. Remove the 2 nuts and belt anchor bracket.
17. REMOVE RECLINING SEAT ADJUSTER ASSEMBLY WITH NO. 2 VERTICAL SEAT LINK SUB-ASSEMBLY
a. Driver's seat:
Using a torx socket wrench, remove the 4 bolts and reclining seat adjuster assembly with No. 2 vertical seat link sub-assembly.
b. Except driver's seat:
Remove the 4 bolts and reclining seat adjuster assembly.
c. Remove the 2 screws and reclining motor.
18. Driver's seat:
REMOVE NO. 2 VERTICAL SEAT LINK SUB-ASSEMBLY AND FRONT VERTICAL MOTOR
a. Using a torx socket wrench, remove the 2 bolts.
b. Remove the 2 nuts and No. 2 vertical seat link sub-assembly.
c. Remove the 2 screws and front vertical motor.
19. Driver's seat:
REMOVE VERTICAL SEAT LINK SUB-ASSEMBLY AND REAR VERTICAL MOTOR
a. w/ Seat position control relay:
Remove the bolt.
b. Remove the 5 nuts, plate and vertical seat link sub-assembly.
c. Remove the 2 screws and rear vertical motor.
20. REMOVE SLIDE MOTOR
a. Remove the 2 screws.
b. Disconnect the seat adjuster drive cable, then remove the slide motor.
REASSEMBLY
1. INSTALL SLIDE MOTOR
Connect the seat adjuster drive cable, then install slide motor with the 2 screws.
2. Driver's seat:
INSTALL VERTICAL SEAT LINK SUB-ASSEMBLY AND REAR VERTICAL MOTOR
a. Install the rear vertical motor with the 2 screws.
b. Install the plate and vertical seat link sub-assembly with the 5 nuts.
Torque: 26 N.m (270 kgf.cm, 20 ft.lbf)
c. w/ Seat position control relay:
Install the bolt.
Torque: 7.8 N.m (80 kgf.cm, 69 in.lbf)
3. Driver's seat:
INSTALL NO. 2 VERTICAL SEAT LINK SUB-ASSEMBLY AND FRONT VERTICAL MOTOR
a. Install the front vertical motor with the 2 screws.
b. Install the No. 2 vertical seat link sub-assembly with the 2 nuts.
Torque: 19 N.m (200 kgf.cm, 14 ft.lbf)
c. Install the 2 bolts.
Torque: 29 N.m (300 kgf.cm, 22 ft.lbf)
4. INSTALL RECLINING SEAT ADJUSTER ASSEMBLY WITH NO. 2 VERTICAL SEAT LINK SUB ASSEMBLY
a. Install the reclining motor with the 2 screws.
b. Driver's seat:
Using a torx socket wrench, install the reclining seat adjuster assembly with No. 2 vertical seat link sub-assembly with the 4 bolts.
Torque: 19 N.m (200 kgf.cm, 14 ft.lbf)
c. Except driver's seat:
Install the seat adjuster assembly with the 4 bolts.
Torque: 19 N.m (200 kgf.cm, 14 ft.lbf)
5. INSTALL SEAT TRACK COVERS AND BELT ANCHOR BRACKET
a. Install the anchor bracket with the 2 nuts.
Torque: 26 N.m (270 kgf.cm, 20 ft.lbf)
b. Install the 2 seat track covers.
6. Driver's seat:
INSTALL TORSION BAR
Using a screwdriver, install the torsion bar.
7. Driver's seat:
INSTALL SEAT POSITION CONTROL RELAY
Install the seat position control relay with the 2 nuts.
8. INSTAL WIRE HARNESS
Connect the connectors, then install the wire harness to the seat adjuster.
9. INSTALL POWER SEAT SWITCH
Install the power seat switch with the 2 screws.
10. INSTALL FRONT SEAT INNER BELT
Install the front seat inner belt with the bolt.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
11. INSTALL SEATBACK COVER
a. Install the seatback cover with the new hog rings to the seatback pad.
b. Driver's seat:
Install the lumber support assembly with the 2 bolts to the seatback frame.
c. Install the seatback cover with pad to the seatback frame with the new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
d. Install the armrest, wave washer and washer with the bolt, then install the cap.
e. Install the headrest supports.
f. Engage the seat cover hook and retainer, then install the 2 screws to the seatback frame.
g. Install the new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
12. INSTALL SEATBACK ASSEMBLY
a. Mount the seatback assembly on the seat adjuster assembly.
b. Connect the lumber support assembly connector.
c. Install the wire harness to the seat cushion inside covers as shown in the illustration.
NOTE: Be careful not to damage the wire harness.
d. Install the seat cushion inside covers with the 6 screws.
e. Install the 4 seatback assembly set bolts.
Torque: 37 N.m (375 kgf.cm, 27 ft.lbf)
f. Engage the wire harness clamps.
g. Install the new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
h. Install the seatback board as shown in the illustration.
13. INSTALL SEAT CUSHION COVER
a. Install the seat cushion cover with new hog rings to the seat cushion pad.
b. Install the seat cushion cover with pad to the seat cushion frame.
c. Engage the seat cushion cover hook.
d. Install new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
14. INSTALL SEAT CUSHION ASSEMBLY
a. Install the seat cushion assembly with the 4 bolts to the seat adjuster.
Torque: 18 N.m (184 kgf.cm, 13 ft.lbf)
b. Install the wire harness to the seat cushion as shown in the illustration.
15. INSTALL NO. 1 FRONT SEAT CUSHION SHIELD
Install the No. 1 front seat cushion shield with the 2 screws.
16. INSTALL FRONT SEAT INNER CUSHION COVER
Install the front seat inner cushion cover with the 3 screws.
17. INSTALL FRONT SEAT CUSHION SHIELD
a. Connect the connector, then install the front seat cushion shield with the 4 screws.
b. Install the power seat switch knobs.
18. INSTALL HEADREST