Operation CHARM: Car repair manuals for everyone.

System Inspection

INSPECTION

1. HEADLAMP DIMMER SWITCH ASSEMBLY







a. Inspect the light control switch continuity.
1. Check continuity between terminals at each switch position as shown in the chart.




b. Inspect the headlamp dimmer switch continuity.
1. Check continuity between terminals at each switch position as shown in the chart.




c. Inspect the turn signal switch continuity.
1. Check continuity between terminals at each switch position as shown in the chart.




d. Inspect the front fog lamp switch continuity.
1. Check continuity between terminals at each switch position as shown in the chart.

2. HAZARD WARNING SIGNAL SWITCH ASSEMBLY







a. Check continuity between terminals at each switch position as shown in the chart.
b. Inspect illumination operation.
1. Connect the battery positive (+) lead to terminal 4 and the battery negative (-) lead to terminal 5, then check that the illumination comes on.

3. FRONT DOOR COURTESY LAMP SWITCH ASSEMBLY
a. Inspect courtesy lamp assembly continuity.
1. Check continuity between terminals when the switch is operated.

Standard:
ON (When shaft is pressed): No continuity
OFF (When shaft Is not pressed): Continuity

4. REAR DOOR COURTESY LAMP SWITCH ASSEMBLY
a. Inspect courtesy lamp assembly continuity.
1. Check continuity between terminal and the switch body when the switch is operated.

Standard:
ON (When shaft is pressed): No continuity
OFF (When shaft is not pressed): Continuity

5. BACK DOOR COURTESY LAMP SWITCH ASSEMBLY
a. Inspect courtesy lamp assembly continuity.
1. Check continuity between terminal and the switch body when the switch is operated.

Standard:
ON (When shaft is pressed): No continuity
OFF (When shaft is not pressed): Continuity

6. GLOVE BOX LAMP SWITCH
a. Inspect courtesy lamp assembly continuity.
1. Check continuity between terminals when the switch is operated.

Standard:
ON (When shaft is pressed): No continuity
OFF (When shaft is not pressed): Continuity

7. HEADLAMP RELAY




a. Inspect relay continuity.




Standard:

8. TAIL LAMP RELAY




a. Inspect relay continuity.




Standard:







9. FOG LAMP RELAY
a. Inspect the relay continuity.




10. ROOM LAMP CONTROL RELAY (DOME RELAY)
a. Inspect relay continuity.




Standard:




11. PARK/NEUTRAL POSITION SWITCH RELAY (BK/UP RELAY)
a. Inspect relay continuity.




Standard:




12. TOWING CONVERTER RELAY (BATT CHG RELAY)
a. inspect relay continuity.




Standard:




13. TOWING CONVERTER RELAY (TOWING TAIL RELAY)
a. Inspect relay continuity.




Standard:




14. TRANSPONDER KEY AMPLIFIER
a. Connect the battery positive (+) lead to terminal 2 and the battery negative (-) lead to terminal 6, and check that the indicator light comes on.




15. MAP LAMP ASSEMBLY
a. Inspect map light assembly continuity.
1. Check continuity between terminals at each switch position as shown in the chart.




Standard:




16. ROOM LAMP ASSEMBLY NO.1
a. Inspect room lamp assembly No.1 continuity.
1. Check continuity between terminals at each switch position as shown in the chart.




Standard:




17. ROOM LAMP ASSEMBLY NO.2
a. Inspect room lamp assembly No.2 continuity.
1. Check continuity between terminals at each switch position as shown in the chart.




Standard:

18. FRONT DOOR COURTESY LAMP ASSEMBLY RH
a. Check continuity between terminals.

Standard: Continuity exists

19. FRONT DOOR COURTESY LAMP ASSEMBLY LH
a. Check continuity between terminals.

Standard: Continuity exists

20. GLOVE BOX LAMP ASSEMBLY
a. Check continuity between terminals.

Standard: Continuity exists

21. RH VISOR ASSEMBLY
a. Inspect vanity light continuity.
1. Check continuity between terminal 1 and 2 when the light is operated.

Standard:
OFF (closed): No continuity
ON (opened): Continuity

22. LH VISOR ASSEMBLY
a. Inspect vanity light continuity.
1. Check continuity between terminal 1 and 2 when the light is operated.

Standard:
OFF (closed): No continuity
ON (opened): Continuity




23. STOP LAMP SWITCH ASSEMBLY
a. Check continuity between terminals at each switch position as shown in the chart.




Standard:




24. LAMP ASSEMBLY, INTERIOR ILLUMINATION, NO.1 (Inside Handle Illumination)
a. Check continuity between terminal 1 (+B) and 2 (GND).

Standard: Continuity

HINT: Connect the positive (+) terminal of the tester to the terminal 1(+B) of the connector, and the negative (-) terminal of the tester to the terminal 2 (GND) of the connector to check the continuity.




25. INTERIOR ILLUMINATION LAMP ASSEMBLY NO.2 (Driver Side Foot Light)
a. Check continuity between terminal 1 (+B) and 2 (GND).

Standard: Continuity

HINT: Connect the positive (+) terminal of the tester to the terminal 1(+B) of the connector, and the negative (-) terminal of the tester to the terminal 2 (GND) of the connector to check the continuity.




26. INTERIOR ILLUMINATION LAMP ASSEMBLY NO.2 (Front Passenger Side Foot Light)
a. Check continuity between terminal 1 (+B) and 2 (GND).

Standard: Continuity

HINT: Connect the positive (+) terminal of the tester to the terminal 1(+B) of the connector, and the negative (-) terminal of the tester to the terminal 2 (GND) of the connector to check the continuity.

27. STEP LAMP ASSEMBLY(RH Side)
a. Inspect the side step lamp assembly.
1. Check continuity between terminals when the courtesy lamp switch is operated.

Standard:
ON: Continuity
OFF: No continuity

28. STEP LAMP ASSEMBLY(LH Side)
2. Check continuity between terminals when the courtesy lamp switch is operated.

Standard:
ON: Continuity
OFF: No continuity