Repair Instruction - Customize Parameters
INTRODUCTION: REPAIR INSTRUCTION:
CUSTOMIZE PARAMETERS
HINT: The following items can be customized.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
1. POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
Tilt &Telescopic:
2. AIR CONDITIONING SYSTEM
Air Conditioner
3. THEFT DETERRENT SYSTEM
Security
4. LIGHTING SYSTEM
Illuminated Entry
Light Control
HINT: Sensitivity adjustment can hardly be confirmed. Please check by customer's actual driving.
Table *1
**1: The new one has the logic to light up two times brighter than the old logic.
**2: Delay time until the headlight is turned on when it suddenly gets dark.
5. WIPER AND WASHER SYSTEM
Wiper
6. POWER DOOR LOCK CONTROL SYSTEM
Body ECU
7. WIRELESS DOOR LOCK CONTROL SYSTEM
(*1): with Power Back Door
(*2): without Power Back Door
8. METER/GAUGE SYSTEM
HINT: The following item can be customized.
NOTICE:
- Be sure to record the current value before customizing.
- When performing troubleshooting, be aware that the functions may be set to OFF by customizing. (Example: In case of the symptom in which "The wireless operation does not function", check that the wireless operation is not set to OFF by customizing, then perform the troubleshooting.)
(a) Key reminder warning buzzer
Combination Meter:
*1: U.S.A.
*2: Except U.S.A.
HINT: This setting can be customized using the Techstream.
(b) SEAT BELT BUZZER ON/OFF SETTING
The buzzer ON/OFF setting, which is a setting of the buzzer function of the combination meter, can disable the driver and front passenger side seat belt buzzers.
NOTICE:
- These buzzers should be on for safe driving. Perform these procedures only if it is necessary to set the buzzer off (disabled).
- When either the battery cable or the combination meter connector is disconnected, these buzzers are set on (enabled).
- Odometer returns to 0 after starting this procedure, although it is not displayed.
HINT: "SEAT BELT BUZZER OFF" indicates that the buzzer is OFF. "SEAT BELT BUZZER ON" indicates that the buzzer is ON. The buzzer ON/OFF setting will be finished (the odometer will display "ODO") if the ODO/TRIP switch is not operated for 10 seconds or more. In this case, perform step 11 to check that the buzzer ON/OFF setting is complete. If it is not complete, start from step 1 again.
(1) Driver and front passenger side seat belt buzzers
1 Turn the ignition switch to the ON position.
2 Press the ODO/TRIP switch until the odometer displays "ODO".
3 Ignition switch off.
4 Turn the ignition switch to the ON position.
5 Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
6 Continue holding down the ODO/TRIP switch and fasten the driver side seat belt.
7 Check that the odometer displays either "SEAT BELT BUZZER ON" or "SEAT BELT BUZZER OFF".
8 Press the ODO/TRIP switch to change the display to "SEAT BELT BUZZER OFF".
9 Ignition switch off.
10 Turn the ignition switch to the ON position.
11 Check that no buzzer sounds at the vehicle speed is 20 km/h (12 mph) or more.
(2) Front passenger side seat belt buzzer:
1 Turn the ignition switch to the ON position.
2 Press the ODO/TRIP switch until the odometer displays "ODO".
3 Ignition switch off.
4 Turn the ignition switch to the ON position.
5 Sit in the front passenger seat. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
6 Sit in the front passenger seat. Continue holding down the ODO/TRIP switch and fasten the front passenger side seat belt.
7 Check that the odometer displays either "SEAT BELT BUZZER ON" or "SEAT BELT BUZZER OFF".
8 Press the ODO/TRIP switch to change the display to "SEAT BELT BUZZER OFF".
9 Ignition switch off.
10 Turn the ignition switch to the ON position.
11 Check that no buzzer sounds at the vehicle speed is 20 km/h (12 mph) or more.
(c) TIME ZONE SETTING (w/ Navigation System)
9. POWER WINDOW CONTROL SYSTEM
POWER WINDOW:
10. POWER BACK DOOR SYSTEM
Power back door ECU
HINT:
- *1: Wireless (transmitter switch) operation of the power back door is disabled.
- *2: When this item is set to ON:
When the back door is fully closed, pulling the back door opener switch (outside handle switch) activates the power back door system to automatically open the back door after that it is unlatched.
11. SLIDING ROOF SYSTEM
CUSTOMIZING FUNCTION WITH TECHSTREAM (REFERENCE)
Slide Roof