Operation CHARM: Car repair manuals for everyone.
Home >> Lexus Truck >> 2008 >> RX 400h FWD V6-3.3L (3MZ-FE) Hybrid >> Repair and Diagnosis >> Brakes and Traction Control >> Antilock Brakes / Traction Control Systems >> Testing and Inspection >> Programming and Relearning >> Initialization

Initialization








BRAKE CONTROL: ELECTRONICALLY CONTROLLED BRAKE SYSTEM:

INITIALIZATION

1. DESCRIPTION
(a) Perform initialization of linear solenoid valve and calibration when the skid control ECU, brake actuator or brake pedal stroke sensor is replaced.
Follow the chart to perform initialization.
HINT:
- If there is a problem with auxiliary battery (12 V) voltage, initialization of linear solenoid valve and calibration cannot be completed normally. Make sure to check battery voltage before performing initialization of linear solenoid valve and calibration.
- If the actuator's temperature is high, initialization of linear solenoid valve and calibration may not be completed normally. In that case, wait until the temperature decreases and then perform initialization of linear solenoid valve and calibration.
- If the ignition switch is turned off, the brake pedal is operated or vehicle speed is input while the linear solenoid valve offset learning is being performed, the learning will be cancelled.





2. CLEAR STORED VALUE OF THE LINEAR SOLENOID VALVE CALIBRATION (WHEN USING TECHSTREAM):
(a) Connect Techstream to the DLC3.
(b) Move the shift lever to the P position.
(c) Turn the ignition switch on with the brake pedal released.
(d) Perform the Reset Memory function under the ABS/VSC/TRAC menu.
(e) Perform initialization of linear solenoid valve.
(f) Perform zero point calibration of yaw rate and deceleration sensor Calibration.
3. PERFORM INITIALIZATION OF LINEAR SOLENOID VALVE AND CALIBRATION (WHEN USING TECHSTREAM):
(a) Connect Techstream to the DLC3.
(b) Move the shift lever to the P position.
(c) Turn the ignition switch on with the brake pedal released.
NOTICE:
- If the linear solenoid valve offset learning is performed without turning the ignition switch on, the learning process may not be completed properly because of insufficient battery voltage.
- When the linear solenoid valve offset learning is interrupted, or the learning process is performed with the shift lever not in the P position, DTC C1345/66 will be stored.

(d) Access "Linear Valve Offset Calibration" under ABS/VSC/TRAC: ECB* Utility.
*: Electronically Controlled Brake
(e) Leave the vehicle stationary without depressing the brake pedal for 1-2 minutes.






(f) Check that the interval between blinks of the brake control warning light changes from 1 second to 0.25 seconds.
- The time needed to complete initialization of linear solenoid valve and calibration varies depending on battery voltage.
- The brake control warning light blinks at 1 second intervals during the initialization of linear solenoid valve and calibration and changes to the test mode display.
- The brake control warning light blinks at 0.25 seconds intervals if the test mode is normal.

(g) Check that DTC C1345/66 that indicates trouble with stroke sensor zero point learning is not output when the brake control warning light changes to the test mode display upon initialization of linear solenoid valve and calibration completion.
(h) Enter the normal mode from the test mode following the Techstream screen.
HINT: Refer to the Techstream operator's manual for further details.

4. CLEAR STORED VALUE OF INITIALIZATION OF LINEAR SOLENOID VALVE AND CALIBRATION (WHEN USING SST CHECK WIRE):






(a) Move the shift lever to the P position.

(b) Turn the ignition switch on with the brake pedal released.
(c) Using SST, connect and disconnect terminals TS and CG of the DLC3 4 times or more within 8 seconds.
SST: 09843-18040
(d) Check that no codes other than ABS code 42, VSC code 45 and Electronically Controlled Brake code 48, 66, or 95 are stored in the diagnostic system.
HINT: The ABS warning light and multi information display do not indicate the normal system code.





(e) Remove the SST from the terminals of the DLC3.
(f) Using the check wire, perform initialization of linear solenoid valve and calibration.
5. PERFORM INITIALIZATION OF LINEAR SOLENOID VALVE AND CALIBRATION (WHEN USING SST CHECK WIRE):






(a) Using SST, connect terminals TS and CG of the DLC3.
SST: 09843-18040

(b) Move the shift lever to the P position.
(c) Turn the ignition switch on with the brake pedal released.
NOTICE:
- If the linear solenoid valve offset learning is performed without turning the ignition switch on, the learning process may not be completed properly because of insufficient battery voltage.
- When the linear solenoid valve offset learning is interrupted, or the learning process is performed with the shift lever not in the P position, DTC C1345/66 will be stored.

(d) Leave the vehicle stationary without depressing the brake pedal for 1 or 2 minutes.






(e) Check that the interval between blinks of the brake control warning light changes from 1 second to 0.25 seconds.
- The time needed to complete initialization of linear solenoid valve and calibration varies depending on battery voltage.
- The brake control warning light blinks at 1 second intervals during the initialization of linear solenoid valve and calibration and changes to the test mode display.
- The brake control warning light blinks at 0.25 seconds intervals if the test mode is normal.

(f) Check that DTC C1345/66 that indicates trouble with stroke sensor zero point learning is not output when the brake control warning light changes to the test mode display upon initialization of linear solenoid valve and calibration completion.
(g) Turn the ignition switch off and disconnect the SST from the DLC3.
pro multis · About Operation CHARM