Operation CHARM: Car repair manuals for everyone.

Up to 08/2009





AUDIO / VIDEO: REAR SEAT ENTERTAINMENT SYSTEM: B15CE: Seatback Display Disconnected
B15CE - Seatback Display Disconnected

DESCRIPTION

The television display assembly and multi-display controller sub-assembly are connected by an AVC-LAN communication line.

The display and navigation module display is connected to the multi-display controller sub-assembly by a MOST communication line.

This DTC will be stored when an AVC-LAN communication error occurs between the multi-display controller sub-assembly and television display assembly.





HINT
* Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
* The display and navigation module display is the master unit.
WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. CHECK DTC

(a) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.

(b) Recheck for DTCs and check if the same trouble occurs again.

Result:





B -- END
A -- Continue to next step.

2. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

(a) Check for optional components.

(1) Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:





HINT
* Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
* This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
B -- CHECK DTC
A -- Continue to next step.

3. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

(a) Remove optional components (including associated wiring).

NOTICE:
Do not remove optional components or associated wiring without the permission of the customer.

NEXT -- Continue to next step.

4. CHECK DTC

(a) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.

(b) Recheck for DTCs and check if the same trouble occurs again.

OK:

No DTCs are output.

NG -- CHECK OPERATION

OK -- END

1. CHECK OPERATION

(a) Check which television display assembly does not operate.

Result:





B -- CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY RH POWER SOURCE)
A -- Continue to next step.

2. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY LH POWER SOURCE)

(a) Disconnect the television display assembly LH connector.





(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration





NG -- CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY LH)
OK -- Continue to next step.

3. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY LH)

(a) Disconnect the multi-display controller sub-assembly connector.





(b) Disconnect the television display assembly LH connector.





(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

4. REPLACE TELEVISION DISPLAY ASSEMBLY LH

(a) Replace the television display assembly LH Removal.

(b) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.

(c) Recheck for DTCs and check if the same trouble occurs again.

OK:

No DTCs are output.

NG -- REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY Removal

OK -- END (TELEVISION DISPLAY ASSEMBLY LH WAS DEFECTIVE)

1. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY LH)

(a) Disconnect the multi-display controller sub-assembly connector.





(b) Disconnect the television display assembly LH connector.





(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR

OK -- REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY Removal

1. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY RH POWER SOURCE)

(a) Disconnect the television display assembly RH connector.





(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration





NG -- CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY RH)
OK -- Continue to next step.

2. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY RH)

(a) Disconnect the multi-display controller sub-assembly connector.





(b) Disconnect the television display assembly RH connector.





(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

3. REPLACE TELEVISION DISPLAY ASSEMBLY RH

(a) Replace the television display assembly RH Removal.

(b) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.

(c) Recheck for DTCs and check if the same trouble occurs again.

OK:

No DTCs are output.

NG -- REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY Removal

OK -- END (TELEVISION DISPLAY ASSEMBLY RH WAS DEFECTIVE)

4. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER - TELEVISION DISPLAY ASSEMBLY RH)

(a) Disconnect the multi-display controller sub-assembly connector.





(b) Disconnect the television display assembly RH connector.





(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR

OK -- REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY Removal