Part 3
50. CHECK REAR AIRBAG SENSOR RH(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Return the side airbag sensor LH (for front side) and side airbag sensor RH (for front side) to their original positions and connect the connectors.
(d) Interchange the rear airbag sensor LH with RH and connect the connectors.
(e) Connect the cable to the negative (-) battery terminal.
(f) Turn the engine switch on (IG), and wait for at least 60 seconds.
(g) Clear the DTCs stored in the memory DTC Check / Clear.
(h) Turn the engine switch off.
(i) Turn the engine switch on (IG), and wait for at least 60 seconds.
(j) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT
Codes other than DTC B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting
B -- REPLACE REAR AIRBAG SENSOR RH
A -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal
51. CHECK FRONT DOOR WIRE RH (OPEN)
(a) Disconnect the front door wire RH connector from the floor wire.
HINT
SST has already been inserted into connector E.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE FLOOR WIRE
52. CHECK FRONT DOOR WIRE RH (SHORT)
(a) Disconnect the front door wire RH connector from the floor wire.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE FLOOR WIRE
53. CHECK FRONT DOOR WIRE RH (SHORT TO B+)
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Disconnect the front door wire RH connector from the floor wire.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG).
(f) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE FLOOR WIRE
54. CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
(a) Disconnect the front door wire RH connector from the floor wire.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- REPLACE FRONT DOOR WIRE RH
OK -- REPLACE FLOOR WIRE
55. CHECK PRESENT DTC
(a) Turn the engine switch on (IG), and wait for at least 60 seconds.
(b) Check the present DTCs DTC Check / Clear.
Result:
HINT
Codes other than present DTC B1622 and B1632 may be output at this time, but they are not related to this check.
B -- CHECK REAR AIRBAG SENSOR RH
A -- Continue to next step.
56. CHECK SIDE AIRBAG SENSOR RH (FOR REAR SIDE)
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Interchange the side airbag sensor LH (for rear side) with side airbag sensor RH (for rear side) and connect the connectors.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in the memory DTC Check / Clear.
(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT
Codes other than DTC B1622 and B1627 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting
B -- REPLACE SIDE AIRBAG SENSOR RH (FOR REAR SIDE)
A -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal
57. CHECK REAR AIRBAG SENSOR RH
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Interchange the rear airbag sensor LH with RH and connect the connectors to them.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in the memory DTC Check / Clear.
(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT
Codes other than DTC B1632 and B1637 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting
B -- REPLACE REAR AIRBAG SENSOR RH
A -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal