Part 3
39. CHECK WIRE HARNESS (SHORT TO B+)(a) Connect the cable to the negative (-) battery terminal.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
NG -- CHECK FRONT DOOR WIRE LH (SHORT TO B+)
OK -- Continue to next step.
40. CHECK WIRE HARNESS (SHORT TO GROUND)
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- CHECK FRONT DOOR WIRE LH (SHORT TO GROUND)
OK -- Continue to next step.
41. CHECK REAR AIRBAG SENSOR LH
(a) Connect the connector to the side airbag sensor LH (for rear side) and side airbag sensor LH (for front side).
(b) Interchange the rear airbag sensor RH with LH and connect the connectors.
(c) Connect the cable to the negative (-) battery terminal.
(d) Turn the engine switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in the the memory DTC Check / Clear.
(f) Turn the engine switch off.
(g) Turn the engine switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT
Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting
B -- REPLACE REAR AIRBAG SENSOR LH
A -- Continue to next step.
42. CHECK SIDE AIRBAG SENSOR LH (FOR FRONT SIDE)
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Return the rear airbag sensor RH and LH to their original positions and connect the connectors.
(d) Interchange the side airbag sensor RH (for front side) with side airbag sensor LH (for front side) and connect the connectors.
(e) Connect the cable to the negative (-) battery terminal.
(f) Turn the engine switch on (IG), and wait for at least 60 seconds.
(g) Clear the DTCs stored in the the memory DTC Check / Clear.
(h) Turn the engine switch off.
(i) Turn the engine switch on (IG), and wait for at least 60 seconds.
(j) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT
Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting
B -- REPLACE SIDE AIRBAG SENSOR LH (FOR FRONT SIDE) Removal
A -- Continue to next step.
43. CHECK SIDE AIRBAG SENSOR LH (FOR REAR SIDE)
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Return the side airbag sensor RH (for front side) and side airbag sensor LH (for front side) to their original positions and connect the connectors.
(d) Interchange the side airbag sensor RH (for rear side) with side airbag sensor LH (for rear side) and connect the connectors.
(e) Connect the cable to the negative (-) battery terminal.
(f) Turn the engine switch on (IG), and wait for at least 60 seconds.
(g) Clear the DTCs stored in the the memory DTC Check / Clear.
(h) Turn the engine switch off.
(i) Turn the engine switch on (IG), and wait for at least 60 seconds.
(j) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT
Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting
B -- REPLACE SIDE AIRBAG SENSOR LH (FOR REAR SIDE)
A -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal
44. CHECK CONNECTORS
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the rear airbag sensor LH and side airbag sensor LH (for front side). Also check that the connectors that link the No. 2 floor wire and front door wire LH are properly connected.
OK:
The connectors are properly connected.
HINT
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
(d) Disconnect the connectors from the rear airbag sensor LH and side airbag sensor LH (for front side). Also disconnect the connectors that link the No. 2 floor wire and front door wire LH.
(e) Check that the terminals of connectors are not damaged.
OK:
The terminals are not deformed or damaged.
NG -- REPLACE WIRE HARNESS
OK -- Continue to next step.
45. CHECK WIRE HARNESS (OPEN)
(a) Connect the connectors that link the No. 2 floor wire and front door wire LH.
(b) Using SST, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.
NOTICE:
Do not forcibly insert SST into the terminals of the connector when connecting.
SST : 09843-18040
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- CHECK FRONT DOOR WIRE LH (OPEN)
OK -- Continue to next step.
46. CHECK WIRE HARNESS (SHORT)
(a) Disconnect SST from connector E.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- CHECK FRONT DOOR WIRE LH (SHORT)
OK -- Continue to next step.
47. CHECK WIRE HARNESS (SHORT TO B+)
(a) Connect the cable to the negative (-) battery terminal.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
NG -- CHECK FRONT DOOR WIRE LH (SHORT TO B+)
OK -- Continue to next step.
48. CHECK WIRE HARNESS (SHORT TO GROUND)
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
NOTICE:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
NG -- CHECK FRONT DOOR WIRE LH (SHORT TO GROUND)
OK -- Continue to next step.
49. CHECK SIDE AIRBAG SENSOR LH (FOR FRONT SIDE)
(a) Connect the connectors to the rear airbag sensor LH.
(b) Interchange the side airbag sensor RH (for front side) with side airbag sensor LH (for front side) and connect the connectors.
(c) Connect the cable to the negative (-) battery terminal.
(d) Turn the engine switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in the the memory DTC Check / Clear.
(f) Turn the engine switch off.
(g) Turn the engine switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs DTC Check / Clear.
Result:
Text in Illustration
HINT
Codes other than DTC B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.
C -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting
B -- REPLACE SIDE AIRBAG SENSOR LH (FOR FRONT SIDE) Removal
A -- Continue to next step.