Up to 08/2009
SUPPLEMENTAL RESTRAINT SYSTEMS: OCCUPANT CLASSIFICATION SYSTEM: B1785: Front Occupant Classification Sensor LH Collision Detection
B1785 - Front Occupant Classification Sensor LH Collision Detection
DESCRIPTION
DTC B1785 is stored when the occupant classification ECU receives a collision detection signal sent by the front occupant classification sensor LH if an accident occurs.
DTC B1785 is also stored when the front seat assembly RH is subjected to a strong impact, even if an actual accident does not occur.
If the vehicle is not in a collision, but the occupant classification ECU outputs a collision detection signal and sets DTC B1785, the DTC can be cleared by performing the Zero Point Calibration and Sensitivity Check.
Therefore, if DTC B1785 is output, first perform Zero Point Calibration and Sensitivity Check.
HINT
When DTC B1650/32 is detected as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant classification ECU. When DTC B1785 is output, perform troubleshooting for the DTC.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1. PERFORM ZERO POINT CALIBRATION
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Using the Techstream, perform Zero Point Calibration Programming and Relearning.
OK:
"Zero Point Calibration is complete." is displayed.
NG -- REPLACE FRONT SEAT ASSEMBLY RH
OK -- Continue to next step.
2. PERFORM SENSITIVITY CHECK
(a) Using the Techstream, perform Sensitivity Check Programming and Relearning.
Standard:
27 to 33 kg (59.5 to 72.8 lb)
NG -- REPLACE FRONT SEAT ASSEMBLY RH
OK -- Continue to next step.
3. CHECK DTC
(a) Turn the engine switch on (IG).
(b) Clear the DTCs stored in the occupant classification ECU Reading and Clearing Diagnostic Trouble Codes.
(c) Clear the DTCs stored in the center airbag sensor assembly DTC Check / Clear.
(d) Turn the engine switch off.
(e) Turn the engine switch on (IG).
(f) Check for DTCs Reading and Clearing Diagnostic Trouble Codes.
OK:
DTC B1785 is not output.
HINT
Codes other than DTC B1785 may be output at this time, but they are not related to this check.
NG -- REPLACE FRONT SEAT ASSEMBLY RH
OK -- END
4. REPLACE FRONT SEAT ASSEMBLY RH
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
(c) Replace the front seat assembly RH Removal.
HINT
Perform the inspection using parts from a normal vehicle if possible.
NEXT -- Continue to next step.
5. PERFORM ZERO POINT CALIBRATION
(a) Connect the cable to the negative (-) battery terminal.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG).
(d) Using the Techstream, perform Zero Point Calibration Programming and Relearning.
OK:
"Zero Point Calibration is complete." is displayed.
NG -- REPLACE OCCUPANT CLASSIFICATION ECU
OK -- Continue to next step.
6. PERFORM SENSITIVITY CHECK
(a) Using the Techstream, perform Sensitivity Check Programming and Relearning.
Standard:
27 to 33 kg (59.5 to 72.8 lb)
NG -- REPLACE OCCUPANT CLASSIFICATION ECU
OK -- Continue to next step.
7. CHECK DTC
(a) Turn the engine switch on (IG).
(b) Clear the DTCs stored in the occupant classification ECU Reading and Clearing Diagnostic Trouble Codes.
(c) Clear the DTCs stored in the center airbag sensor assembly DTC Check / Clear.
(d) Turn the engine switch off.
(e) Turn the engine switch on (IG).
(f) Check for DTCs Reading and Clearing Diagnostic Trouble Codes.
OK:
DTC B1785 is not output.
HINT
Codes other than DTC B1785 may be output at this time, but they are not related to this check.
NG -- REPLACE OCCUPANT CLASSIFICATION ECU
OK -- END
8. REPLACE OCCUPANT CLASSIFICATION ECU
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
(c) Replace the occupant classification ECU Removal.
NEXT -- Continue to next step.
9. PERFORM ZERO POINT CALIBRATION
(a) Connect the cable to the negative (-) battery terminal.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG).
(d) Using the Techstream, perform Zero Point Calibration Programming and Relearning.
OK:
"Zero Point Calibration is complete." is displayed.
NEXT -- Continue to next step.
10. PERFORM SENSITIVITY CHECK
(a) Using the Techstream, perform Sensitivity Check Programming and Relearning.
Standard:
27 to 33 kg (59.5 to 72.8 lb)
NEXT -- END