Operation CHARM: Car repair manuals for everyone.

Up to 08/2009





INTERIOR PANELS / TRIM: ROOF HEADLINING: INSTALLATION

1. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (Brown) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.





Text in Illustration





NOTICE:
After installation, check that the corners fit correctly.

2. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.





Text in Illustration





NOTICE:
After installation, check that the corners fit correctly.

3. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Align the alignment mark (Light Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.





Text in Illustration





NOTICE:
After installation, check that the corners fit correctly.

4. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Align the alignment mark (Green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.





Text in Illustration





NOTICE:
After installation, check that the corners fit correctly.

5. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Pull the roof headlining assembly into the vehicle through the back door.





NOTICE:
Do not damage the roof headlining assembly or body interior.

(b) Engage the 2 fasteners.





(c) Engage the 12 claws and 3 clips.

(d) Connect the No. 4 antenna cord sub-assembly connector and engage the 2 claws and clamp from the rear pillar LH.

(e) w/ Rain Sensor:

(1) Connect the No. 1 roof wire connector to the rain sensor.

(f) Connect the No. 1 roof wire connector to the inner rear view mirror.

(g) Connect the No. 2 antenna cord sub-assembly connector and washer hose, and engage the 2 claws to the front pillar RH.

(h) Connect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors, and engage the 2 claws to the front pillar LH.





NOTICE:
After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

(i) Connect the No. 2 antenna cord sub-assembly connectors and washer hose, and engage the 2 claws and 3 clamps to the rear pillar RH.





6. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Pull the roof headlining assembly into the vehicle through the back door.





NOTICE:
Do not damage the roof headlining assembly or body interior.

(b) Engage the 8 fasteners.





(c) Engage the 12 claws and 3 clips.

(d) Connect the No. 4 antenna cord sub-assembly connector and engage the 2 claws and clamp to the rear pillar LH.

(e) w/ Rain Sensor:

(1) Connect the No. 1 roof wire connector to the rain sensor.

(f) Connect the No. 1 roof wire connector to the inner rear view mirror.

(g) Connect the No. 2 antenna cord sub-assembly connector and washer hose, and engage the 2 claws to the front pillar RH.

(h) Connect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors, and engage the 2 claws to the front pillar LH.





NOTICE:
After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

(i) Connect the No. 2 antenna cord sub-assembly connectors and washer hose, and engage the 2 claws and 3 clamps to the rear pillar RH.





7. INSTALL VISOR HOLDER (for LH Side)

(a) Engage the 2 claws.





(b) Push in the visor holder as shown in the illustration.

8. INSTALL VISOR HOLDER (for RH Side)

HINT
Use the same procedure for the RH side and the LH side.

9. INSTALL VISOR ASSEMBLY LH

(a) Install the visor assembly LH with the 2 screws.





10. INSTALL VISOR BRACKET COVER (for LH Side)

(a) Engage the 4 claws and install the visor bracket cover.





11. INSTALL VISOR ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

12. INSTALL VISOR BRACKET COVER (for RH Side)

HINT
Use the same procedure for the RH side and the LH side.

13. INSTALL ASSIST GRIP SUB-ASSEMBLY

(a) Put an assist grip sub-assembly together as shown in the illustration.





(b) Install the assist grip sub-assembly.

HINT
Use the same procedure for the other 3 assist grips.

14. INSTALL COAT HOOK

(a) Install the coat hook with the screw.





HINT
Use the same procedure for the RH side and the LH side.

15. INSTALL RAIN SENSOR COVER (w/ Rain Sensor) Installation

16. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/o Automatic High Beam System) Installation

17. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Automatic High Beam System) Installation

18. INSTALL SPOT LIGHT ASSEMBLY Installation

19. INSTALL MAP LIGHT ASSEMBLY Installation

20. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH

(a) Pass the floor anchor of the rear seat outer seat belt assembly LH through the roof side inner garnish assembly LH.

(b) Engage the claw and 8 clips to install the roof side inner garnish assembly LH.





21. CONNECT REAR SEAT OUTER BELT ASSEMBLY LH Installation

22. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

(a) Connect each connector.

(b) Engage the 2 clips and the 5 claws.

(c) Install the deck trim side panel assembly LH with the 2 bolts and 4 clips.





23. INSTALL RECLINING REMOTE CONTROL BEZEL LH

(a) Engage the 4 claws and install the reclining remote control bezel LH.





24. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)

(a) Install the No. 1 luggage compartment trim hook as shown in the illustration.





25. INSTALL ROPE HOOK ASSEMBLY (for LH Side)

(a) Install the 2 rope hook assemblies with the 2 bolts.





(b) Engage the 2 claws.

26. INSTALL REAR SEAT SIDE COVER LH

(a) Engage the 2 claws and 3 clips.





(b) Install the rear seat side cover LH with the 2 clips.

27. INSTALL REAR SEAT ASSEMBLY LH

(a) Install the rear seat assembly LH Installation.

28. INSTALL REAR FLOOR FINISH SIDE PLATE LH

(a) Engage the guide.





(b) Engage the claw and 2 clips.

(c) Install the rear floor finish side plate LH with the clip.

29. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

30. CONNECT REAR SEAT OUTER BELT ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

31. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

(a) Connect the connector.

(b) Engage the 2 clips and the 5 claws.

(c) Install the deck trim side panel assembly RH with the 2 bolts and 4 clips.





32. INSTALL HEIGHT CONTROL SWITCH (w/ Air Suspension) Installation

33. INSTALL RECLINING REMOTE CONTROL BEZEL RH

HINT
Use the same procedure for the RH side and the LH side.

34. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

(a) Install the No. 1 luggage compartment trim hook as shown in the illustration.





35. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

HINT
Use the same procedure for the RH side and the LH side.

36. INSTALL REAR SEAT SIDE COVER RH

HINT
Use the same procedure for the RH side and the LH side.

37. INSTALL REAR SEAT ASSEMBLY RH

(a) Install the rear seat assembly RH Installation.

38. INSTALL REAR FLOOR FINISH SIDE PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

39. INSTALL REAR FLOOR FINISH PLATE

(a) Engage the 6 clips, 2 claws and 2 guides, and install the rear floor finish plate.





40. INSTALL FRONT DECK FLOOR BOX

(a) Install the front deck floor box with the clip.





41. INSTALL DECK SIDE TRIM BOX LH (for Compact Spare Tire)

(a) Install the deck side trim box LH with the 2 clips.





42. INSTALL DECK SIDE TRIM BOX LH (for Full Size Spare Tire)

(a) Install the deck side trim box LH with the 3 clips.





43. INSTALL DECK SIDE TRIM BOX RH (for Compact Spare Tire)

(a) Install the deck side trim box RH with the 2 clips.





44. INSTALL DECK SIDE TRIM BOX RH (for Full Size Spare Tire)

(a) Install the deck side trim box RH with the 3 clips.





45. INSTALL REAR DECK FLOOR BOX

(a) Install the rear deck floor box with the 3 clips.





46. INSTALL TONNEAU COVER ASSEMBLY

(a) Install the tonneau cover assembly.

47. INSTALL NO. 3 REAR FLOOR BOARD (for Compact Spare Tire)

(a) Engage the 2 guides and install the No. 3 rear floor board.





48. INSTALL NO. 3 REAR FLOOR BOARD (for Full Size Spare Tire)

(a) Engage the 2 guides and install the No. 3 rear floor board.





49. INSTALL NO. 4 REAR FLOOR BOARD (for Compact Spare Tire)

(a) Engage the 2 guides and install the No. 4 rear floor board.





50. INSTALL NO. 4 REAR FLOOR BOARD (for Full Size Spare Tire)

(a) Engage the 2 guides and install the No. 4 rear floor board.





51. INSTALL SPARE WHEEL COVER ASSEMBLY (for Compact Spare Tire)

(a) Install the spare wheel cover assembly.

52. INSTALL DECK BOARD SUB-ASSEMBLY

(a) for Compact Spare Tire:

(1) Install the deck board sub-assembly with the 2 bolts.





(b) for Full Size Spare Tire:

(1) Install the deck board sub-assembly with the 2 bolts.





(c) Engage the 3 fasteners as shown in the illustration.





53. INSTALL CENTER PILLAR GARNISH LH

(a) Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH.

(b) Engage the clip to install the center pillar garnish LH with the 2 screws.





54. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH Installation

55. INSTALL LOWER CENTER PILLAR GARNISH LH

(a) Engage the 2 claws and the 5 clips to install the lower center pillar garnish LH.





56. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the 3 clips, guide and 6 claws, and install the rear door scuff plate LH.





57. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.





Text in Illustration





(b) Install a new clip [A] on the front pillar garnish LH.





(c) Engage the 2 guides and 2 clips, then install the front pillar garnish LH.

58. INSTALL INSTRUMENT SIDE PANEL LH

(a) Engage the guide.





(b) Engage the 2 clips.

(c) Engage the claw to install the instrument side panel LH.

59. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

(a) Engage the 2 clips to install the cowl side trim sub-assembly LH.





(b) Install the clip.

60. INSTALL FRONT DOOR SCUFF PLATE LH

(a) w/ Illumination:

(1) Connect the connector.

(b) Engage the 4 clips, guide and 7 claws, and install the front door scuff plate LH.





61. INSTALL CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

62. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

63. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

64. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

65. INSTALL FRONT PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

66. INSTALL INSTRUMENT SIDE PANEL RH

HINT
Use the same procedure for the RH side and the LH side.

67. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

68. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

69. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Air Suspension)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

70. INSPECT SUSPENSION CONTROL SYSTEM (w/ Air Suspension)

(a) Inspect the suspension control system Test Mode Procedure.