Up to 08/2009

SEAT: REAR SEAT ASSEMBLY (for RH Side): REASSEMBLY

1. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY RH

(a) Using a T45 "TORX" socket wrench, install the rear seat cushion spring assembly with the 4 bolts and 4 bushes.





Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

2. INSTALL REAR SEAT RECLINING CONTROL CABLE

(a) Engage the claw to install the rear seat hook.





(b) Engage the 4 rear seat hooks.

(c) Engage the 6 cable clamps and install the rear seat reclining control cable.





3. INSTALL NO. 2 REAR SEAT COVER

(a) Install the No. 2 rear seat cover with the screw.





4. INSTALL NO. 1 REAR SEAT COVER

(a) Install the No. 1 rear seat cover with the screw.





5. INSTALL REAR SEAT RECLINING INNER COVER RH

(a) Engage the 2 guides.





(b) Install the rear seat reclining inner cover RH with the screw.

6. INSTALL REAR SEAT CUSHION SIDE COVER LH

(a) Engage the claw.





(b) Install the rear seat cushion side cover LH with the 2 screws.

7. INSTALL REAR SEAT CUSHION MOULDING RH

(a) Engage the 3 claws.





(b) Install the rear seat cushion moulding RH with the 3 screws.

8. INSTALL REAR SEATBACK COVER RH

(a) Engage the claw.





(b) Install the rear seatback cover RH with the 2 screws.

9. INSTALL SEPARATE TYPE REAR SEATBACK COVER

(a) Using hog ring pliers, install the separate type rear seatback cover with 12 new hog rings.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
10. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY Installation

11. INSTALL REAR SEAT SHOULDER BELT COVER Installation

12. INSTALL BELT SUPPORT PLATE

(a) Engage the 3 claws to install the belt support plate.





13. INSTALL REAR SEATBACK COVER WITH PAD

(a) Using hog ring pliers, install a new hog ring.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog ring, take care to minimize wrinkles as much as possible.
(b) Engage the hook.

(c) Install the rear seat belt hook with the bolt.





Torque : 6.0 Nm (61 kgf-cm, 53 in-lbf)

(d) Install the rear seatback cover bracket with the nut.





Torque : 5.6 Nm (57 kgf-cm, 50 in-lbf)

NOTICE:
* For vehicles with side airbags, the side airbags may not be activated normally unless the rear seatback cover is securely installed.
* Check that the strap is not twisted after installing the bracket.
* Install the bracket securely.
(e) Using hog ring pliers, install 6 new hog rings.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(f) Engage the 5 hooks.

(g) Engage the 2 fasteners and install the rear seatback cover with pad.





Text in Illustration





14. INSTALL REAR SEAT HEADREST SUPPORT RH

(a) Engage the 2 claws to install the rear seat headrest support RH.





15. INSTALL REAR SEAT HEADREST SUPPORT LH

(a) Engage the 2 claws to install the rear seat headrest support LH.





16. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY Installation

17. INSTALL REAR SEAT SHOULDER BELT HOLE COVER

(a) Move the rear seat shoulder belt hole cover in the direction indicated by the arrow in the illustration to engage the 2 guides.





(b) Move the rear seat shoulder belt hole cover in the direction indicated by the arrow in the illustration to engage the 2 claws and install the cover.

18. INSTALL SEAT BELT ANCHOR COVER CAP

(a) Engage the 2 claws and install the seat belt anchor cover cap.





19. INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY

(a) Engage the guide.





(b) Install the No. 1 fold seat stopper band assembly with the bolt.

Torque : 9.0 Nm (92 kgf-cm, 80 in-lbf)

20. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH

(a) Engage the guide.





(b) Engage the 2 clips and install the rear seatback board carpet assembly RH.

21. INSTALL REAR SEATBACK COVER RH

(a) Engage the 4 claws to install the rear seatback cover RH.





22. INSTALL TONNEAU COVER HOOK HOLDER

(a) Engage the 2 guides.





(b) Install the 2 tonneau cover hook holders with the 2 screws.

23. INSTALL REAR SEAT LOCK STRIKER

(a) Using a T45 "TORX" socket, install the "TORX" bolt to the rear seat lock striker.





Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

24. INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR

(a) Install the rear seatback lock striker protector.





25. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

(a) Using hog ring pliers, install the separate type rear seat cushion cover with 11 new hog rings.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
26. INSTALL REAR SEAT CUSHION COVER WITH PAD

(a) Using hog ring pliers, install 2 new hog rings.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(b) Using hog ring pliers, install 2 new hog rings.





NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(c) Engage the 2 elastic bands.





(d) Engage each hook.





(e) Engage the 2 hooks to install the rear seat cushion cover with pad.





27. INSTALL REAR SEAT CUSHION MOULDING RH

(a) Engage the 2 guides as shown in the illustration.





(b) Install the rear seat cushion moulding RH with the 2 screws.

28. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH

(a) Install the No. 1 reclining adjuster release handle RH with the 3 screws.





29. INSTALL REAR SEAT COVER CAP

(a) Engage the 3 claws to install the rear seat cover cap.





30. INSTALL REAR SEAT CENTER ARMREST BOX

(a) Install the rear seat center armrest box.





31. INSTALL REAR SEAT CENTER ARMREST DOOR SUB-ASSEMBLY

(a) Install the rear seat center armrest door sub-assembly with the 2 screws.





32. INSTALL CUP HOLDER

(a) Engage the 2 clips.





(b) Install the cup holder with the 2 screws.

33. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

34. INSTALL NO. 2 REAR SEAT RECLINING SPACER

(a) Install the No. 2 rear seat reclining spacer to the rear seat center armrest assembly.





35. INSTALL REAR SEAT CENTER ARMREST SUPPORT RH

(a) Engage the guide and install the nut.





(b) Using a T45 "TORX" socket, remove the "TORX" bolt, bush, and the rear seat center armrest support RH.





Torque : 13 Nm (128 kgf-cm, 9 ft-lbf)

36. INSTALL REAR SEATBACK MOULDING RH

(a) Engage the 2 guides.





(b) Install the rear seatback moulding RH with the 3 screws.

37. INSTALL REAR SEATBACK MOULDING LH

(a) Engage the 2 guides.





(b) Install the rear seatback moulding LH with the 3 screws.

38. INSTALL REAR CENTER SEATBACK HINGE

(a) Using a T45 "TORX" socket, remove the "TORX" bolt, bush, and the rear center seatback hinge.





Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

39. REMOVE REAR SEATBACK HINGE LH

(a) Using a T45 "TORX" socket, remove the "TORX" bolt, bush, and the rear seatback hinge LH.





Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

40. INSTALL CENTER SEAT CUSHION FRAME SUB-ASSEMBLY

(a) Using a T45 "TORX" socket, tighten the 2 "TORX" bolts and 2 bushes and install the center seat cushion frame sub-assembly.





Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

41. INSTALL NO. 2 CENTER SEATBACK COVER

(a) Engage the 2 claws.





(b) Install the No. 2 center seatback cover with the screw.

42. INSTALL NO. 1 SEATBACK COVER

(a) Connect the rod as shown in the illustration.





(b) Engage the guide.





(c) Install the rear seat reclining cover with the 2 screws.

43. INSTALL COAT HOOK CAP

(a) Engage the 2 claws and guide, and install the coat hook cap as shown in the illustration.





44. INSTALL REAR SEAT CENTER HEADREST SUPPORT RH

(a) Engage the 2 claws to install the rear seat center headrest support RH.





45. INSTALL REAR SEAT CENTER HEADREST SUPPORT LH

(a) Engage the 2 claws to install the rear seat center headrest support LH.





46. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY

(a) Disengage the 4 clips and install the rear seatback board sub-assembly.





47. INSTALL REAR SEATBACK LOCK COVER RH

(a) Engage the 4 guides and claw, and install the rear seatback lock cover RH as shown in the illustration.





48. INSTALL REAR CENTER SEATBACK COVER

(a) Engage the 4 claws to install the rear center seatback cover.





49. INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY

(a) Engage the center seat cushion cover sub-assembly to the center seat cushion as shown in the illustration.





50. INSTALL CENTER SEAT CUSHION COVER WITH PAD

(a) Engage each hook as shown in the illustration.





(b) Engage the 2 hooks and install the center seat cushion cover with pad as shown in the illustration.





51. INSTALL RECLINING COVER PROTECTOR RH

(a) Engage the reclining cover protector RH as shown in the illustration.





(b) Install the screw.





(c) Install the reclining cover protector RH with the clip.

52. INSTALL RECLINING COVER PROTECTOR LH

(a) Engage the reclining cover protector LH as shown in the illustration.





(b) Install the screw.





(c) Install the reclining cover protector LH with the clip.

53. INSTALL REAR CENTER SEAT ASSEMBLY

(a) Engage the elastic band.





(b) Install the rear seat center seat assembly with the 4 bolts.





Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

54. INSTALL UPPER CENTER SEAT HINGE COVER LH

(a) Install the upper center seat hinge cover LH.





55. INSTALL REAR SEAT INNER BELT ASSEMBLY Installation