From 08/2009

SEAT: REAR SEAT ASSEMBLY (for LH Side): REASSEMBLY

1. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY LH

(a) Using a T45 "TORX" socket wrench, install the rear seat cushion spring assembly LH with the 4 bolts and 4 bushes.

Torque : 21 Nm (214 kgf-cm, 16 ft-lbf)

2. INSTALL NO. 2 REAR SEAT RECLINING CONTROL CABLE

(a) Engage the claw to install the rear seat hook.

(b) Engage the 4 rear seat hooks.

(c) Engage the 6 cable clamps and install the No. 2 rear seat reclining control cable.

3. INSTALL REAR SEAT RECLINING INNER COVER LH

(a) Engage the 2 claws.

(b) Install the rear seat reclining inner cover LH with the screw.

4. INSTALL REAR SEAT CUSHION SIDE COVER LH

(a) Engage the claw.

(b) Install the rear seat cushion side cover LH with the 2 screws.

5. INSTALL NO. 2 REAR SEAT INNER SHIELD COVER

(a) Engage the claw.

(b) Install the No. 2 rear seat inner shield cover with the 2 screws.

6. INSTALL NO. 3 REAR SEAT COVER

(a) Install the No. 3 rear seat cover with the screw.

7. INSTALL SEPARATE TYPE REAR SEATBACK COVER

(a) Using hog ring pliers, install the separate type rear seatback cover with 12 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(b) As shown in the illustration, pass the bracket of the separate type rear seatback cover through the separate type rear seatback pad.

NOTICE:
After installing the bracket, check that the band is not twisted.

8. INSTALL REAR SEATBACK COVER WITH PAD

(a) Temporarily install the side airbag so that it is stored inside the rear seatback cover with pad.

Text in Illustration

(b) Install bracket A onto the bolt and insert the guide.

Text in Illustration

(c) Install bracket B onto the bolt and insert the guide.

(d) Install the rear seatback cover bracket with the nut.

Torque : 5.6 Nm (57 kgf-cm, 50 in-lbf)

NOTICE:
* For vehicles with side airbags, the side airbags may not be activated normally unless the rear seatback cover is securely installed.
* Check that the strap is not twisted after installing the bracket.
* Install the bracket securely.
(e) Using hog ring pliers, install a new hog ring.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog ring, take care to minimize wrinkles as much as possible.
(f) Engage the hook.

(g) Install the rear seat belt hook with the bolt.

Torque : 6.0 Nm (61 kgf-cm, 53 in-lbf)

(h) Using hog ring pliers, install 6 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(i) Engage the 5 hooks.

(j) Engage the 2 fasteners and install the rear seatback cover with pad.

Text in Illustration

9. INSTALL REAR SEAT HEADREST SUPPORT RH

(a) Engage the 2 claws to install the rear seat headrest support RH.

10. INSTALL REAR SEAT HEADREST SUPPORT LH

(a) Engage the 2 claws to install the rear seat headrest support LH.

11. INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY

(a) Engage the guide.

(b) Install the No. 1 fold seat stopper band assembly with the bolt.

Torque : 9.0 Nm (92 kgf-cm, 80 in-lbf)

12. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH

(a) Engage the guide.

(b) Engage the 2 clips to install the rear seatback board carpet assembly LH.

13. INSTALL REAR SEATBACK COVER

(a) Engage the 4 claws to install the rear seatback cover.

14. INSTALL TONNEAU COVER HOOK HOLDER

(a) Engage the 2 guides.

(b) Install the 2 tonneau cover hook holders with the 2 screws.

15. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

(a) Using hog ring pliers, install the separate type rear seat cushion cover with 11 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
16. INSTALL REAR SEAT INNER BELT ASSEMBLY LH Installation

17. INSTALL REAR SEAT CUSHION COVER WITH PAD

(a) Using hog ring pliers, install 2 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(b) Engage the 2 hooks.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(d) Engage each hook as shown in the illustration.

(e) Engage the 2 elastic bands to install the rear seat cushion cover with pad.

18. INSTALL REAR SEAT CUSHION MOULDING RH

(a) Engage the 4 claws.

(b) Install the rear seat cushion moulding RH with the 3 screws.

19. INSTALL REAR SEAT CUSHION MOULDING LH

(a) Engage the guide as shown in the illustration.

(b) Engage the 2 guides.

(c) Install the rear seat cushion moulding LH with the 2 screws.

20. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH

(a) Install the No. 1 reclining adjuster release handle LH with the 3 screws.

21. INSTALL REAR SEAT COVER CAP

(a) Engage the 3 claws to install the rear seat cover cap.

22. INSTALL REAR CENTER INNER BELT ASSEMBLY LH Installation