Part 3

INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

10. REMOVAL AND INSTALLATION OF ENGINE INTAKE PARTS

(a) If any metal particles enter intake system parts, this may damage the engine.

(b) When removing and installing intake system parts, cover the openings of the removed parts and engine openings. Use adhesive tape or other suitable materials.

(c) When installing intake system parts, check that no metal particles have entered the engine or installed parts.

11. HANDLING OF HOSE CLAMPS

Text in Illustration

(a) Before removing a hose, check the clamp position so that it can be reinstalled in the same position.

(b) Replace any deformed or dented clamps with new ones.

(c) When reusing a hose, attach the clamp on the clamp track portion of the hose.

(d) For a spring type clamp, it may be necessary to spread the tabs slightly after installation by pushing them in the direction of the arrows as shown in the illustration.

12. FOR VEHICLES EQUIPPED WITH MOBILE COMMUNICATION SYSTEMS

(a) Install an antenna as far away from the ECU and sensors of the vehicle electronic systems as possible.

(b) Install an antenna and feeder at least 20 cm (7.87 in.) away from the ECU and sensors of the vehicle electronic systems. For details about ECU and sensor locations, refer to the section on the applicable components.

(c) Keep the antenna and feeder separate from other wiring as much as possible. This will prevent signals sent from the communication equipment from affecting vehicle equipment and vice versa.

(d) Check that the antenna and feeder are correctly adjusted.

(e) Do not install a high-powered mobile communication system.

13. HEADLIGHT INSPECTION OR MAINTENANCE

(a) When the headlight dimmer switch assembly is set to head, do not touch the discharge headlight high-voltage socket area.

NOTICE:
When performing inspection or maintenance, the discharge headlight precautions must be followed.

(b) When the headlights are illuminated, do not cover the headlights for 3 minutes or more.

Text in Illustration

NOTICE:
As the headlight outer lens is made of resin, the resulting heat created when covering the headlight for an extended period of time may deform the headlight.

14. FOR VEHICLES EQUIPPED WITH AIR SUSPENSION SYSTEM

(a) Before raising the vehicle using a jack or lift, or working under the vehicle, make sure to disable vehicle height control using the height control OFF switch.

HINT
* When vehicle height control is disabled using the height control OFF switch, "HEIGHT CONTROL OFF" will be shown on the multi-information display in the combination meter.
* The history that vehicle height control has been disabled using the height control OFF switch will remain even if the cable is disconnected from the negative (-) battery terminal.
* Vehicle height control disabled using the height control OFF switch will resume when the vehicle speed reaches 30 km/h (19 mph).
* In order to resume vehicle height control disabled using the height control OFF switch, push the height control OFF switch again with the engine running and the power switch on (IG).
15. FOR VEHICLES EQUIPPED WITH TRACTION CONTROL (TR(A)C) AND VEHICLE STABILITY CONTROL (VSC) SYSTEMS

(a) NOTICES FOR WHEN TESTING WITH DRUM TESTER

(1) When testing with a 2-wheel drum tester such as a speedometer tester, a combination speedometer and brake tester, or a chassis dynamometer, perform the following procedure to enter inspection mode and disable the TR(A)C and VSC systems Component Tests and General Diagnostics.

NOTICE:
* If the vehicle is tested in normal mode on the tester, TR(A)C and VSC operation may cause the vehicle to jump out from the tester.
* Check that "FWD Maintenance Mode" is displayed on the multi-information display.
* Secure the vehicle with chains for safety.
HINT
Pressing the VSC OFF switch (for vehicles with a VSC OFF switch) does not disable TR(A)C and VSC operation completely.

(b) NOTICES FOR VSC RELATED PROCEDURES

(1) For VSC related parts, adjustments are required after removal and installation. Therefore, perform removal and installation only when necessary.

(2) When performing VSC related procedures, be sure to strictly follow the preparation and completion procedures.

(3) When performing removal and installation or replacement of VSC related parts, first disconnect the cable from the negative (-) battery terminal.

16. WHEN INSPECTING VEHICLES

NOTICE:
If the vehicle is run in the inspection mode, for such as a speedometer test, a DTC may be set. Therefore, if the warning light comes on, after canceling the inspection mode, check for DTCs using the Techstream and clear the DTCs.

(a) VEHICLE CONDITIONS

(1) Before activating inspection mode, turn the air conditioning off, start the engine with the shift lever in P, and check the engine stops within several seconds after starting (engine warm up check).

(2) Activate inspection mode and inspect the vehicle Component Tests and General Diagnostics.

The shift position for each test is as follows:

(3) Reset inspection mode immediately after completion of inspection.

NOTICE:
Driving the vehicle without resetting inspection mode may damage the transaxle.

(b) WHEN USING A BRAKE TESTER

HINT
When inspecting the brakes using the brake tester, the braking force of the rear wheels may be reduced. When the vehicle speed is 0 km/h (0 mph), the brake control system of the vehicle limits the rear brake fluid pressure to approximately 50% of the normal brake fluid pressure when driving the vehicle, in order to reduce energy consumption.

NOTICE:
* A high-speed type brake tester cannot be used.
* Vehicle speed should be less than 0.5 km/h (0.3 mph).
* Follow all usage and safety procedures in the operator's manual for the brake tester.
(1) Place the wheels to be tested (front or rear) onto the rollers.

(2) Move the shift lever to N.

(3) Start the engine to allow normal brake booster operation.

(4) Operate the brakes to perform the test.

(c) WHEN USING A SPEEDOMETER TESTER

CAUTION:
Be sure to perform the test in the FWD inspection mode.

NOTICE:
Do not use a chassis dynamometer to perform rapid starting or quick acceleration/deceleration without first setting the proper load on the dynamometer. Failing to set the load may damage the transaxle.

(1) Depress the accelerator pedal slowly and gradually accelerate the vehicle. Make a measurement.

(2) After the measurement, use the brakes to gradually decelerate the vehicle.

(d) WHEN USING A CHASSIS DYNAMOMETER

(1) Always set an appropriate load before starting the test.

NOTICE:
Sudden acceleration or deceleration of the vehicle on a chassis dynamometer under minimal load may damage the transaxle.

(e) WHEN USING AN ON-VEHICLE BALANCER

(1) Raise the vehicle until all 4 wheels are off the ground.

(2) Support the vehicle with safety stands at an appropriate height. Make sure that vehicle does not lean in any direction, and that the tires are completely clear of the floor.

(3) Place the vibration pick-up unit into position for the wheel to be measured*1.

(4) Release the parking brake.

(5) Check that no dragging force exists when turning each wheel by hand.

(6) Put the wheel balancer in position.

(7) Wheel balance measurement should be done by using both the engine and the wheel balancer drive roller to spin the wheels.

HINT
*1: Different on-vehicle wheel balancers have different requirements for mounting the vibration pick-up unit(s). Refer to the operator's manual for the wheel balancer to confirm requirements for use.

NOTICE:
* Be sure to perform the test in FWD maintenance mode.
* Start the engine and then increase the vehicle speed gradually with the shift lever in D.
* Do not accelerate or decelerate suddenly.
* Deceleration should be done by braking gradually.
* Make sure that no one is standing in-line with the spinning wheels.
* Measurement should be done quickly.
* Confirm that the vehicle is securely immobilized.
* Follow all usage and safety procedures in the operator's manual for the wheel balancer.
17. WHEN TOWING AWD VEHICLES

(a) Use one of the following methods to tow the vehicle.

(b) If the vehicle has trouble with the chassis or drive train, use method 1 (flat bed truck).

NOTICE:
Do not use any towing method other than those shown above.

(c) If a tow truck is not available, in an emergency vehicle may be temporarily towed using a cable or chain secured to the emergency towing eyelet(s). This should only be attempted on hard surfaced roads for short distances below 30 km/h (19 mph).

A driver must be in the vehicle to steer and operate the brakes. The vehicle's wheels, drive train, axles, steering and brakes must be in good condition.

(1) Emergency towing procedure

1 Release the parking brake.

2 Shift the shift lever to N.

3 Turn the power switch on (IG).

NOTICE:
* Use extreme caution when towing the vehicle.
* Avoid sudden starts or erratic driving maneuvers which place excessive stress on the emergency towing eyelet and the cables or chains.
* If the hybrid system is off, the power assist for the brakes and steering will not function, making steering and braking more difficult.
(d) The following towing methods shown below are dangerous and can damage the vehicle, so do not use them.

(1) Do not tow the vehicle with only two wheels on the ground.

(2) Do not use a sling-type towing method either from the front or rear.

NOTICE:
If these towing methods are used either from the front or rear, the following may occur.

* The drive train may overheat and be damaged and the wheels may come off the dolly.
* If a sling-type tow truck is used, damage may occur to the vehicle body.
18. WHEN TOWING FWD VEHICLES

(a) Use one of the following methods to tow the vehicle.

(b) If the vehicle has trouble with the chassis or drive train, use method 1 (flat bed truck).

(1) Do not tow the vehicle with only front wheels on the ground.

(2) Do not use a sling-type towing method either from the front or rear.

NOTICE:
If these towing methods are used either from the front or rear, the following may occur.

* The drive train may overheat and be damaged.
* If a sling-type tow truck is used, damage may occur to the vehicle body.
19. FOR VEHICLES EQUIPPED WITH CATALYTIC CONVERTER

CAUTION:
If a large amount of unburned gasoline or gasoline vapors flow into the converter, it may cause converter overheating and create a fire hazard. To prevent this, observe the following precautions:

(a) Use only unleaded gasoline.

(b) Avoid performing unnecessary spark tests.

(1) Perform a spark test only when absolutely necessary. Perform this test as rapidly as possible with the injector connector disconnected.

(2) While testing, never race the engine unless instructed.

(c) Do not run the engine when the fuel tank is nearly empty. This may cause the engine to misfire and create an extra load on the converter.