Repair Instruction - Customize Parameters
INTRODUCTION: REPAIR INSTRUCTION: CUSTOMIZE PARAMETERS
NOTICE:
* When the customer requests a change in a function, first make sure that the function can be customized.
* Be sure to make a note of the current settings before customizing.
* When troubleshooting a function, first make sure that the function is set to the default setting.
HINT
The following items can be customized.
1. POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
Tilt & Telescopic
2. INTUITIVE PARKING ASSIST SYSTEM
Warning
Sensor
Display
3. INTUITIVE PARKING ASSIST SYSTEM (On Multi-display)
NOTICE:
* When the customer requests a change in a function, first make sure that the function can be customized.
* Be sure to make a note of the current settings before customizing.
* When troubleshooting a function, first make sure that the function is set to the default setting.
(a) Turn the power switch on (IG).
(b) Turn the intuitive parking assist system on.
(c) Select the following menus: Setup / Vehicle / Intuitive park assist.
(d) Select the setting by referring to the table below.
4. POWER DOOR LOCK CONTROL SYSTEM
Door Lock
* *: w/o Occupant Classification System
Illuminated Entry
5. WIRELESS DOOR LOCK CONTROL SYSTEM
Wireless Door Lock Control System
* *: except for Korea
Illuminated Entry
6. SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function)
Smart Key/Access
*: Weak radio waves will still be emitted from oscillators other than the front oscillator even when the "Front" customize setting is selected.
Warning
7. ENTRY UNLOCK MODE SWITCHING (SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function))
NOTICE:
Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.
(a) To change the vehicle entry unlock mode, make sure that the vehicle power is off and simultaneously push and hold the key lock switch and another key switch for 5 seconds.
Driver door unlock default setting:
When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.
NOTICE:
After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.
* Driver door unlock mode:
* When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.
* All door unlock mode:
* When any touch sensor is touched, all doors unlock.
(b) The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the smart access system with push-button start to the entry unlock mode.
(c) The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer assembly and combination meter assembly (buzzer) to inform the user that the mode has been changed.
HINT
The procedure only changes the entry unlock mode of the smart access system with push-button start. It does not switch the unlocking of the wireless door lock control.
8. ELECTRICAL KEY CANCEL (SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Entry Function))
NOTICE:
Because the key (for card type) does not have a wireless transmitter function, it cannot be used to perform the key cancel operation.
The electrical key cancel operation disables the following functions:
* Entry Unlock/Lock
* Entry Hybrid Vehicle Control System Start
* Entry Back Door Open
* Electrical Key Lock-in Prevention
* Warning
* Memory Call
(a) The operation procedures are as follows:
Precondition:
Power switch off, driver side door closed and unlocked.
(1) Push the unlock switch of the key once.
(2) Open the driver door within 5 seconds.
(3) Push the unlock switch of the key twice within 5 seconds.
(4) Close and open the driver door twice within 30 seconds.
(Driver door: Close -> Open -> Close -> Open)
(5) Push the unlock switch of the key twice within 5 seconds.
(6) Close and open the driver door within 30 seconds.
(Driver door: Close -> Open)
(7) Close the driver door within 5 seconds.
When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.
9. SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Start Function)
Smart Access
10. CUSTOMIZING FUNCTION WITHOUT TECHSTREAM (SMART ACCESS SYSTEM WITH PUSH-BUTTON START (for Start Function))
Performing the following procedure disables the smart access system with push-button start.
HINT
To start the hybrid control system while the smart access system with push-button start is disabled, follow the procedure for when the key battery is low.
(a) The operation procedures are as follows:
Precondition:
Power switch off, driver side door closed and unlocked.
(1) Push the unlock switch of the key once.
(2) Open the driver door within 5 seconds.
(3) Push the unlock switch of the key twice within 5 seconds.
(4) Close and open the driver door twice within 30 seconds.
(Driver door: Close -> Open -> Close -> Open)
(5) Push the unlock switch of the key twice within 5 seconds.
(6) Close and open the driver door within 30 seconds.
(Driver door: Close -> Open)
(7) Close the driver door within 5 seconds.
When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.
11. THEFT DETERRENT SYSTEM
Security
* *: w/ Satellite Radio
12. LIGHTING SYSTEM (LIGHTING INT)
Illuminated Entry
13. METER / GAUGE SYSTEM
Warning
* *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more.
14. FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
Main Body
15. SEAT BELT WARNING SYSTEM
Combination Meter
* This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.
16. AIR CONDITIONING SYSTEM
Air Conditioner
* *1: w/ Navigation System
17. POWER WINDOW CONTROL SYSTEM
Power Window
18. SLIDING ROOF SYSTEM
Sliding Roof
* *1: This function is linked with the power window key-linked function. If the power window key-linked function is set to OFF, the sliding roof key-linked function will not operate even when it is set to ON.
* *2: This function is linked with the power window wireless transmitter-linked function. If the power window wireless transmitter-linked function is set to OFF, the sliding roof wireless transmitter-linked function will not operate even when it is set to ON.
19. POWER BACK DOOR SYSTEM
PSD&PBD operation
* *1: The warning buzzer that sounds when the power back door is operating cannot be customized (even if this function is set to "OFF", the buzzer will still sound).
* *2: "Not Use" is not a setting that can be selected.
HINT
When either "One Motion" or "One Motion with Unlock Door" is selected, the other will display "Not Use".
* *3: The power back door assist operation will be linked with the "Back Door Opening Operation" setting of the smart access system with push-button start (for entry function) only when all doors are locked. If "Back Door Opening Operation" is set to "OFF", the power back door assist will not operate even if "PBD Assist Open Operation" is set to "ON".
* *4: for models with the "PBD Assist Open Operation" customize setting item.
20. LIGHTING SYSTEM (LIGHTING EXT)
Light Control
Illuminated Entry
