Part 5
1UR-FE ENGINE CONTROL: SFI SYSTEM: P1604: Startability Malfunction
P1604 - Startability Malfunction - Continued
78. CHECK CRANKSHAFT POSITION SENSOR
(a) Replace the crankshaft position sensor Removal.
(b) Check the engine start operation.
OK:
Malfunction has been repaired successfully.
NG -- CHECK CAMSHAFT POSITION SENSOR
OK -- END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)
79. CHECK CAMSHAFT POSITION SENSOR
(a) Replace the camshaft position sensor Removal.
(b) Check the engine start operation.
OK:
Malfunction has been repaired successfully.
NG -- REPLACE ECM Removal
OK -- END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)
80. CHECK CRANKSHAFT POSITION SENSOR
(a) Check the tightening and installation condition of the crankshaft position sensor bolt.
(b) Check the connection of the crankshaft position sensor connector.
OK:
Sensor is installed correctly.
NG -- SECURELY REINSTALL SENSOR Installation
OK -- Continue to next step.
81. CHECK CAMSHAFT POSITION SENSOR
(a) Check the tightening and installation condition of the camshaft position sensor bolt.
(b) Check the connection of the camshaft position sensor connector.
OK:
Sensor is installed correctly.
NG -- SECURELY REINSTALL SENSOR Installation
OK -- Continue to next step.
82. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
(a) Disconnect the crankshaft position sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
HINT
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
83. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
(a) Disconnect the camshaft position sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
HINT
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
84. CHECK CRANKSHAFT POSITION SENSOR
(a) Replace the crankshaft position sensor Removal.
(b) Check the engine start operation.
OK:
Malfunction has been repaired successfully.
NG -- CHECK CAMSHAFT POSITION SENSOR
OK -- END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)
85. CHECK CAMSHAFT POSITION SENSOR
(a) Replace the camshaft position sensor Removal.
(b) Check the engine start operation.
OK:
Malfunction has been repaired successfully.
NG -- REPLACE ECM Removal
OK -- END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)
86. READ VALUE USING TECHSTREAM (ISC LEARNING VALUE)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches should be off
(d) Using the Techstream, select and read [ISC Learning Value] in the Data List.
Result:
B -- INSPECT ENGINE COOLANT TEMPERATURE SENSOR
A -- Continue to next step.
87. CHECK CYLINDER COMPRESSION PRESSURE
(a) Inspect the compression On-Vehicle Inspection.
NG -- REPAIR OR REPLACE ENGINE ASSEMBLY
OK -- CHECK VALVE TIMING
88. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
(a) Inspect the engine coolant temperature sensor Testing and Inspection.
NG -- REPLACE ENGINE COOLANT TEMPERATURE SENSOR Removal
OK -- Continue to next step.
89. CHECK FUEL PRESSURE
HINT
For the fuel pressure inspection, refer to the following procedures Fuel System.
(a) Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.
Result:
NG -- PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
OK -- Continue to next step.
90. READ VALUE USING TECHSTREAM (LONG FT)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Using the Techstream, select and read [Long FT] in the Data List.
Result:
B -- REPLACE FUEL INJECTOR Removal
A -- Continue to next step.
91. PERFORM SIMULATION TEST
(a) Check if the idling speed after starting the engine is currently stable and has always been stable in the past.
Result:
HINT
Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.
B -- REPLACE FUEL
A -- Continue to next step.
92. CHECK CRANKSHAFT POSITION SENSOR
(a) Check the tightening and installation condition of the crankshaft position sensor bolt.
(b) Check the connection of the crankshaft position sensor connector.
OK:
Sensor is installed correctly.
NG -- SECURELY REINSTALL SENSOR Installation
OK -- Continue to next step.
93. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
(a) Disconnect the crankshaft position sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
HINT
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
94. CHECK CRANKSHAFT POSITION SENSOR
(a) Replace the crankshaft position sensor Removal.
(b) Check the engine start operation.
OK:
Malfunction has been repaired successfully.
NG -- REPLACE ECM Removal
OK -- END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)
95. PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Using the Techstream, select the [Control the Fuel Pump / Speed] Active Test.
(d) When performing the Active Test, check for fuel leakage from the fuel pipes.
Result
HINT
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
B -- INSPECT FUEL PUMP
A -- REPAIR OR REPLACE FUEL LINE
96. INSPECT FUEL PUMP
(a) Inspect the fuel pump Inspection.
NG -- REPLACE FUEL PUMP Removal
OK -- REPLACE PRESSURE REGULATOR Removal
97. CHECK FUEL PRESSURE
HINT
For the fuel pressure inspection, refer to the following procedures Fuel System.
(a) Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
Result:
B -- PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
A -- Continue to next step.
98. READ VALUE USING TECHSTREAM (LONG FT)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Using the Techstream, select and read [Long FT] in the Data List.
Result:
B -- REPLACE FUEL INJECTOR Removal
A -- Continue to next step.
99. PERFORM SIMULATION TEST
(a) Check if the idling speed after starting the engine is currently stable and has always been stable in the past.
Result
HINT
Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.
B -- REPLACE FUEL
A -- Continue to next step.
100. CHECK CRANKSHAFT POSITION SENSOR
(a) Check the tightening and installation condition of the crankshaft position sensor bolt.
(b) Check the connection of the crankshaft position sensor connector.
OK:
Sensor is installed correctly.
NG -- SECURELY REINSTALL SENSOR Installation
OK -- Continue to next step.
101. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
(a) Disconnect the crankshaft position sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
HINT
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
102. CHECK CRANKSHAFT POSITION SENSOR
(a) Replace the crankshaft position sensor Removal.
(b) Check the engine start operation.
OK:
Malfunction has been repaired successfully.
NG -- REPLACE ECM Removal
OK -- END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)
103. PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Using the Techstream, select the [Control the Fuel Pump / Speed] Active Test.
(d) When performing the Active Test, check for fuel leakage from the fuel pipes.
Result
HINT
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
B -- INSPECT FUEL PUMP
A -- REPAIR OR REPLACE FUEL LINE
104. INSPECT FUEL PUMP
(a) Inspect the fuel pump Inspection.
NG -- REPLACE FUEL PUMP Removal
OK -- Continue to next step.
105. CHECK PURGE VSV
(a) Disconnect the vacuum hose (on the canister side) of the purge VSV.
(b) Start the engine.
(c) Idle the engine.
(d) Disconnect the connector of the purge VSV.
(e) Check if air flows through the purge VSV.
Standard:
Air does not flow
(f) Connect the connector of the purge VSV.
(g) Connect the vacuum hose of the purge VSV.
HINT
When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs Reading and Clearing Diagnostic Trouble Codes.
NG -- INSPECT PURGE VSV Testing and Inspection
OK -- Continue to next step.
106. CHECK FUEL INJECTOR
(a) Clean the inside of the surge tank with compressed air.
(b) After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
Result:
HINT
If the concentration is 400 ppm or higher, a fuel injector may have a sealing problem.
B -- CHECK INTAKE VALVE
A -- REPLACE FUEL INJECTOR Removal
107. CHECK INTAKE VALVE
(a) Check if carbon is on the intake valves.
Result:
B -- READ VALUE USING TECHSTREAM (ISC LEARNING VALUE)
A -- CLEAN INTAKE VALVE
108. READ VALUE USING TECHSTREAM (ISC LEARNING VALUE)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
(d) Using the Techstream, select and read [ISC Learning Value] in the Data List.
Result:
B -- INSPECT ENGINE COOLANT TEMPERATURE SENSOR
A -- Continue to next step.
109. CHECK CYLINDER COMPRESSION PRESSURE
(a) Inspect the compression On-Vehicle Inspection.
NG -- REPAIR OR REPLACE ENGINE ASSEMBLY
OK -- ADJUST VALVE TIMING Reassembly
110. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
(a) Inspect the engine coolant temperature sensor Testing and Inspection.
NG -- REPLACE ENGINE COOLANT TEMPERATURE SENSOR Removal
OK -- Continue to next step.
111. CHECK CRANKSHAFT POSITION SENSOR
(a) Check the tightening and installation condition of the crankshaft position sensor bolt.
(b) Check the connection of the crankshaft position sensor connector.
OK:
Sensor is installed correctly.
NG -- SECURELY REINSTALL SENSOR Installation
OK -- Continue to next step.
112. CHECK CAMSHAFT POSITION SENSOR
(a) Check the tightening and installation condition of the camshaft position sensor bolt.
(b) Check the connection of the camshaft position sensor connector.
OK:
Sensor is installed correctly.
NG -- SECURELY REINSTALL SENSOR Installation
OK -- Continue to next step.
113. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
(a) Disconnect the crankshaft position sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
HINT
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
114. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
(a) Disconnect the camshaft position sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
HINT
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
115. CHECK CRANKSHAFT POSITION SENSOR
(a) Replace the crankshaft position sensor Removal.
(b) Check the engine start operation.
OK:
Malfunction has been repaired successfully.
NG -- CHECK CAMSHAFT POSITION SENSOR
OK -- END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)
116. CHECK CAMSHAFT POSITION SENSOR
(a) Replace the camshaft position sensor Removal.
(b) Check the engine start operation.
OK:
Malfunction has been repaired successfully.
NG -- REPLACE ECM Removal
OK -- END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)