Reassembly
DOOR / HATCH: BACK DOOR: REASSEMBLY
1. INSTALL RADIO SETTING CONDENSER Installation
2. INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY Installation
3. INSTALL ROOF HEADLINING ASSEMBLY
HINT
Refer to the procedure from Install Roof Headlining Assembly Installation.
4. INSTALL REAR WASHER NOZZLE Installation
5. INSPECT REAR WASHER NOZZLE Washer Nozzle (for Rear Side)
6. ADJUST REAR WASHER NOZZLE (for Rear Side)
7. INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY Installation
8. INSTALL REAR WIPER MOTOR GROMMET Installation
9. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY Installation
10. INSTALL REAR SPOILER SUB-ASSEMBLY Installation
11. INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Rear Monitor) Installation
12. INSTALL LICENSE PLATE LIGHT ASSEMBLY LH Installation
13. INSTALL LICENSE PLATE LIGHT ASSEMBLY RH
HINT
Use the same procedure for the RH side and LH side.
14. INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
15. INSTALL REAR LIGHT ASSEMBLY LH Installation
16. INSTALL REAR LIGHT ASSEMBLY RH
HINT
Use the same procedure for the RH side and LH side.
17. INSTALL AMPLIFIER ANTENNA ASSEMBLY Installation
18. INSTALL BACK DOOR LOWER STAY BRACKET LH Installation
19. INSTALL BACK DOOR LOWER STAY BRACKET RH
HINT
Use the same procedure for the RH side and LH side.
20. CONNECT BACK DOOR STAY ASSEMBLY LH
(a) Install the stop ring to the power back door rod.
(b) Install the back door stay assembly LH.
NOTICE:
* Install the back door stay assembly while supporting the back door by hand.
* Check that the back door stay assembly is engaged in the ball joint and that the back door stay assembly cannot be pulled out.
21. CONNECT BACK DOOR STAY ASSEMBLY RH
HINT
Use the same procedure for the RH side and LH side.
22. CONNECT POWER BACK DOOR UNIT ASSEMBLY (w/ Power Back Door)
(a) Clean the threaded portion on the vehicle body with a non-residue solvent.
(b) Apply adhesive to the threads of the 2 bolts.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
(c) Connect the power back door unit assembly with the 2 bolts.
Torque : 31 Nm (316 kgf-cm, 23 ft-lbf)
23. INSTALL POWER BACK DOOR TOUCH SENSOR ASSEMBLY LH (w/ Power Back Door) Installation
24. INSTALL POWER BACK DOOR TOUCH SENSOR ASSEMBLY RH (w/ Power Back Door)
HINT
Use the same procedure for the RH side and LH side.
25. INSTALL LOWER BACK DOOR STOPPER LH
(a) Install the lower back door stopper LH with the bolt.
26. INSTALL LOWER BACK DOOR STOPPER RH
HINT
Use the same procedure for the RH side and LH side.
27. INSTALL BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)
(a) Apply MP grease to the sliding parts of the back door lock assembly.
(b) Install the back door lock assembly with the 3 bolts.
Torque : 13 Nm (127 kgf-cm, 9 ft-lbf)
(c) Connect the connector.
28. INSTALL BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)
(a) Apply MP grease to the sliding parts of the back door lock assembly.
(b) Install the back door lock assembly with the 3 bolts.
Torque : 13 Nm (127 kgf-cm, 9 ft-lbf)
(c) Install the bolt.
Torque : 13 Nm (127 kgf-cm, 9 ft-lbf)
(d) Engage the clamp.
(e) Connect the connector.
29. INSTALL BACK DOOR TRIM COVER LH
(a) Engage the 3 clips to install the back door trim cover LH.
30. INSTALL BACK DOOR TRIM COVER RH
(a) Engage the 3 clips to install the back door trim cover RH.
31. INSTALL BACK DOOR TRIM PANEL ASSEMBLY
(a) Engage the 2 claws and 16 clips to install the back door trim panel assembly.
Text in Illustration
(b) Install the 2 screws.
32. INSTALL BACK DOOR SERVICE HOLE COVER LH
(a) Engage the 5 claws to install the back door service hole cover LH.
33. INSTALL BACK DOOR SERVICE HOLE COVER RH
(a) Engage the 5 claws to install the back door service hole cover RH.
34. INSTALL BACK DOOR UPPER TRIM COVER LH
(a) Engage the 2 claws to install the back door upper trim cover LH.
35. INSTALL BACK DOOR UPPER TRIM COVER RH
(a) Engage the 2 claws to install the back door upper trim cover RH.
36. INSTALL NO. 2 ROOM LIGHT ASSEMBLY Installation
37. INSTALL BACK DOOR LOCK COVER
(a) Engage the 4 claws to install the back door lock cover.
38. INSTALL BACK DOOR FINISH COVER LH (w/o Power Back Door)
(a) Engage the 6 claws to install the back door finish cover LH.
39. INSTALL BACK DOOR TRIM BASE (w/ Power Back Door)
(a) Engage the 4 claws to install the back door trim base.
40. INSTALL BACK DOOR FINISH COVER RH (w/o Power Back Door)
(a) Engage the 6 claws to install the back door finish cover RH.
41. INSTALL DOOR PULL HANDLE WITH SWITCH (w/ Power Back Door)
(a) Connect the connector.
(b) Engage the 6 claws to install the door pull handle with switch.
42. INSTALL TONNEAU COVER SUB-ASSEMBLY
43. INSTALL UPPER BACK WINDOW PANEL TRIM
(a) Engage the 7 clips and 6 claws to install the upper back window panel trim.
Text in Illustration
44. ADJUST REAR TELEVISION CAMERA OPTICAL AXIS (CAMERA POSITION SETTINGS) (w/ Parking Assist Monitor System)
Calibration