Front

SEATBACK COVER REMOVAL
1. REMOVE THESE PARTS:
(a) Headrest
(b) Hole cover
(c) Front seat outer belt
(d) Seat track cover
(e) Front seat
Torque: 37 N.m (375 kgf.cm, 27 ft.lbf)






2. REMOVE FRONT SEATBACK BOARD
(a) Remove the 2 screws.
(b) Slide the board downward to remove it.






3. REMOVE SEAT COVER HOOK
Remove the 4 hooks as shown in the illustration.

ASSEMBLY CAUTION: Hang the seat cover hook securely to the fitting, or the side airbag does not operate correctly.

4. REMOVE SIDE AIRBAG ASSEMBLY






5. REMOVE SEATBACK COVER WITH PAD
(a) Remove the hook.

ASSEMBLY CAUTION: Check that hook shown in the illustration (A) is hanging on the seat frame securely before installing the side airbag assembly. If the hook shown as (A) is not securely hanged. there fear of incorrect deploying caused by the sliding of seat cover position.






HINT:
- Side airbag is designed to inflate breaking up the seams of the seatback cover shown in the illustration.
- The position shown in the illustration is made to be hold by installing the side airbag assembly with the hook shown as (A) hanged onto the seat frame.






(b) Remove the hog rings.
(c) Remove the 2 headrest supports.
(d) Remove the seatback cover with pad from the seat-back frame.






6. REMOVE SEATBACK COVER
Remove the seatback cover from the seatback pad.

SEATBACK COVER INSTALLATION
Installation is in the reverse order of removal.






POWER SEAT REGULATOR REMOVAL
1. REMOVE FRONT SEAT CUSHION SHIELD
Remove the 6 screws and front seat cushion shield.
2. REMOVE INNER BELT NUT
3. REMOVE POWER SEAT REGULATOR ASSEMBLY
Remove the 4 bolts and regulator assembly.






POWER SEAT REGULATOR DISASSEMBLY
1. REMOVE POWER SEAT REGULATOR SHIELD
Remove the 2 screws and regulator shield.
2. REMOVE SLIDE MOTOR SUPPORT BRACKET
Remove the 2 nuts and support bracket.






3. REMOVE REAR VERTICAL ASSEMBLY
(a) Remove the 2 bolts from the rear vertical assembly inner side.
(b) Remove the 3 nuts and bracket from the rear vertical assembly outer side.
(c) Remove the rear vertical motor assembly.






4. REMOVE FRONT VERTICAL ASSEMBLY
(a) Using a torx wrench, remove the 3 screws.
(b) Remove the nut and front vertical assembly.






(c) Remove these parts:
(1) Inner front vertical sub-assembly
(2) Outer front vertical sub-assembly
(3) Front vertical motor
(4) Front vertical connecting pipe






5. REMOVE SLIDE MOTOR HOUSING ASSEMBLY
(a) Remove 2 bolts from the inner seat truck.






(b) Move the upper rail rearward and hold the screw shaft with pliers.
(c) Remove the nut.

ASSEMBLY HINT: Apply adhesive to nut. Part no.08833-00070, THREE BOND 1324 or equivalent






(d) Using a hexagon wrench, remove the 2 screws.
(e) Remove the inner bracket from the slide motor housing assembly.






(f) Remove 2 bolts from the outer seat truck.
(9) Move the upper rail rearward and hold the screw shaft with pliers.
(h) Remove the nut and washer.

ASSEMBLY HINT: Apply adhesive to nut. Part no.08833-00070, THREE BOND 1324 or equivalent.






(i) Using a hexagon wrench, remove the 2 screws.
(j) Remove the outer bracket from the slide motor housing assembly.

POWER SEAT REGULATOR ASSEMBLY
Assembly is in the reverse order of disassembly.

POWER SEAT REGULATOR INSTALLATION
Installation is in the reverse order of removal.