Front Seat
Front Seat:
Front Seat:
DISASSEMBLY
1. REMOVE THESE PARTS:
a. Headrest
b. Power seat switch knobs
c. Front seat inner belt
d. No.1 front seat cushion shield
e. Front seat cushion shield
f. Front seat inner cushion cover
2. REMOVE SEAT CUSHION ASSEMBLY
a. Remove the wire harness from the seat cushion assembly.
b. Remove the 4 bolts and seat cushion assembly from the seat adjuster.
3. REMOVE SEAT CUSHION COVER
a. Remove the 2 bolts and hog rings.
b. Remove the seat cushion cover with pad from the seat cushion frame.
c. Remove the seat cushion cover from the seat cushion pad.
4. REMOVE SEATBACK ASSEMBLY
a. Remove the 2 screws and pull the seatback board downward to remove it.
b. Remove the hog rings.
c. Disconnect the connectors.
d. Remove the 4 bolts.
NOTE: Be careful not to damage the wire harness.
e. Remove the 2 screws and seat cushion inside cover then disconnect the wire harness from the cover.
HINT: Do the same for LH and RH.
f. Remove the covers from the outer and inner seat tracks.
5. REMOVE SEATBACK COVER
a. Remove the hog rings.
b. Release the clamp.
c. Remove the 2 bolts and release the seat cover hook and retainer from the seatback frame.
d. Remove the headrest supports.
e. Remove the seatback cover with pad from the seatback frame.
f. Remove the 2 bolts and lumber support assembly from the seatback frame.
g. Remove the hog rings and seatback cover from the seat-back pad
6. REMOVE WIRE HARNESS
Disconnect the connectors, then remove the wire harness.
7. Driver's Seat:
REMOVE SEAT POSITION CONTROL RELAY
Remove the 2 nuts and seat position control relay.
8. REMOVE SLIDE MOTOR
a. Remove the 2 screws.
b. Disconnect the seat adjuster drive cable, then remove the slide motor.
9. REMOVE FRONT VERTICAL MOTOR
Remove the 2 screws and front vertical motor.
10. REMOVE LIFTER MOTOR
Remove the 2 screws and rear vertical motor.
11. REMOVE RECLINING MOTOR
a. Remove the 2 screws.
b. Disconnect the shaft, then remove the reclining motor.
12. REMOVE POWER SEAT SWITCH
Remove the 2 screws and power seat switch.
REASSEMBLY
1. INSTALL RECLINING MOTOR
Connect the shaft, then install the reclining motor with the 2 screws.
2. INSTALL REAR VERTICAL MOTOR
Install the rear vertical motor with the 2 screws.
3. INSTALL FRONT VERTICAL MOTOR
Install the front vertical motor with the 2 screws.
4. INSTALL SLIDE MOTOR
Connect the seat adjuster drive cable, then install the slide motor with the 2 screws.
5. Driver's Seat:
INSTALL SEAT POSITION CONTROL RELAY
Install the seat position control relay with the 2 nuts.
6. INSTALL WIRE HARNESS
Connect the connector, then install the wire harness to the seat adjuster.
7. INSTALL SEATBACK COVER
a. Install the seatback cover with new hog rings to the seat-back pad.
b. Install the lumber support assembly with the 2 bolts to the seatback frame.
c. Install the seatback cover with pad to the seatback frame.
d. Install the seat cover retainer and hook to the seatback assembly with the 2 bolts.
e. Install new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as least as possible.
8. INSTALL SEATBACK ASSEMBLY
a. Install the covers to the outer and inner seat tracks.
b. Install the wire harness to the seat cushion inside covers as shown in the illustration.
NOTE: Be careful not to damage the wire harness.
c. Install the seat cushion inside cover with the 2 screws.
HINT: Do the same for LH and RH.
d. Install the seatback assembly with the 4 bolts.
Torque: 61 N.m (622 kgf.cm, 45 ft.lbf)
e. Install new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as least as possible.
f. Install the seatback board with the 2 screws to the seat-back assembly.
9. INSTALL SEAT CUSHION COVER
a. Install the seat cushion cover with new hog rings to the seat cushion pad.
b. Install the seat cushion cover with pad to the seat cushion frame with new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as least as possible.
10. INSTALL SEAT CUSHION ASSEMBLY
a. Install the seat cushion assembly with the 4 bolts to the seat adjuster.
b. Install the wire harness to the seat cushion, as shown in the illustration.
Torque: 19 N.m (194 kgf.cm, 14 ft.lbf)
11. INSTALL THESE PARTS:
a. Front seat inner cushion cover
b. Front seat cushion shield
c. No.1 front seat cushion shield
d. Front seat inner belt
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
e. Power seat switch knobs
f. Headrest