Removal and Installation
REMOVAL
1. REMOVE LEVEL GAUGE
2. RAISE VEHICLE
NOTICE: Make sure that the vehicle is securely supported.
3. REMOVE ENGINE UNDER COVER
4. REMOVE FRONT SUSPENSION PROTECTOR
5. REMOVE EXHAUST PIPE
a. Disconnect the 2 heated oxygen sensors.
Torque: 44 Nm (450 kgf-cm, 32 ft. lbs.)
HINT: At the time of installation, please refer to the following items.
^ Before installing the heated oxygen sensor, twist the sensor wire counterclockwise 3 and 1/2 turns.
^ After installing the heated oxygen sensor wire is not twisted. If it is twisted, remove the heated oxygen sensor and reinstall it.
b. Remove the 4 bolts, nuts and 2 gaskets from the LH and RH front TWC (unleaded gasoline) or 2 sub-mufflers (leaded gasoline).
Torque: 43 Nm (440 kgf-cm, 32 ft. lbs.)
HINT: At the time of installation, please refer to the following item. Replace the used nuts and gaskets with new ones.
c. Remove the 2 bolts and support bracket.
Torque: 43 Nm (440 kgf-cm, 32 ft. lbs.)
d. Remove the 4 bolts and center floor crossmember brace.
Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.)
e. Remove the exhaust pipe.
6. REMOVE LH AND RH FRONT TWC
Remove the 6 nuts, 2 gaskets, LH and RH front TWC.
Torque: 62 Nm (630 kgf-cm, 46 ft. lbs.)
HINT: At the time of installation, please refer to the following item. Replace the used nuts and gaskets with new ones.
7. REMOVE ENGINE REAR MOUNTING MEMBER BRACKET PLATE
Remove the 3 bolts and bracket plate.
Torque: 5.4 Nm (55 kgf-cm, 48 inch lbs.)
8. REMOVE 2 BOLTS AND FILLER PIPE
HINT: At the time of installation, please refer to the following item. Replace the used O-ring with a new one.
9. REMOVE HEAT INSULATOR
Remove the 4 bolts and heat insulator.
Torque: 5.4 Nm (55 kgf-cm, 48 inch lbs.)
10. REMOVE PROPELLER SHAFT HEAT INSULATOR
Remove the 2 bolts and propeller shaft heat insulator.
Torque: 5.4 Nm (55 kgf-cm, 48 inch lbs.)
11. REMOVE PROPELLER SHAFT.
12. REMOVE SHIFT CONTROL ROD Remove the nut and disconnect the rod.
Torque: 13 Nm (130 kgf-cm, 9 ft. lbs.)
13. DISCONNECT OIL COOLER PIPE
a. Loosen the 2 union nuts from the transmission.
Torque: 44 Nm (450 kgf-cm, 32 ft. lbs.)
NOTICE: Be careful not to damage the oil cooler pipe.
b. Disconnect the 3 set bolts of the clamp.
Torque: 4.9 Nm (50 kgf-cm, 43 inch lbs.)
c. Disconnect the 2 oil cooler pipes from the transmission.
14. REMOVE TORQUE CONVERTER CLUTCH MOUNTING BOLT
a. Remove the 2 bolts and flywheel housing under cover.
Torque: 18 Nm (185 kgf-cm, 13 ft. lbs.)
b. Turn the crankshaft to gain access to each bolt.
c. Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.
Torque: 48 Nm (490 kgf-cm, 35 ft. lbs.)
HINT: At the time of installation, please refer to the following item. First install black colored bolt and then the 5 other bolts.
15. SUPPORT TRANSMISSION WITH JACK
16. REMOVE ENGINE REAR MOUNTING 4 SET BOLTS
Torque: 26 Nm (270 kgf-cm, 20 ft. lbs.)
17. DISCONNECT CONNECTORS AND WIRE HARNESS
a. Tilt down the transmission.
NOTICE: Take care so that the cooling fan does not come in contact with the fan shroud.
b. Disconnect the following connectors:
1. O/D direct clutch speed sensor connector
2. Vehicle speed sensor connector
3. Park/Neutral position switch connector
4. Solenoid connector
c. Disconnect the wire harness from the clamp on transmission.
18. REMOVE TRANSMISSION
Remove the 10 bolts and transmission.
Torque:
14 mm head bolt: 37 Nm (380 kgf-cm, 27 ft. lbs.)
17 mm head bolt: 72 Nm (730 kgf-cm, 53 ft. lbs.)
HINT: At the time of installation, please refer to the following item. Lift the engine front side.
INSTALLATION
1. CHECK TORQUE CONVERTER CLUTCH INSTALLATION
Using calipers and a straight edge, measure from the installed surface of the torque converter clutch to the front surface of the transmission housing.
Correct distance: More than 17.1 mm (0.673 inch)
If the distance is less than the standard, check for an improper installation.
2. INSTALL TRANSMISSION
Installation is in the reverse order of removal.
HINT: After installation, check and inspect items as follows.
^ Adjust the shift lever position.
^ Check fluid level.
^ Do the road test.