Navigation System
DIAGNOSTIC TROUBLE CODE CHART
1. MULTI DISPLAY (Physical address: 110)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code is stored when 180 sec.has passed after the power supply connector is pulled out after engine start.
- *3 This code may be stored when the engine key is turned again after engine start.
- *4: This code may be stored when the engine key is turned again 1 min. after engine start.
21 - 22, D5 - DE:
E2 - E3:
a. Logical address 01 (Communication control)
10 - 11:
b. Logical address: 21 (Switch)
10 - 12:
c. Logical address: 34 (Front passenger monitor)
2. GATEWAY ECU (Physical address: 1C6)
HINT:
*1: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
D4:
Logical address: 01 (Communication control)
3. RADIO AND PLAYER (Physical address: 190)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code is stored when 180 sec has passed after the power supply connector is pulled out after engine start.
- *3: This code may be stored when the engine key is turned again 1 min. after engine start.
- *4: This code may be stored when the engine key is turned again after engine start.
- *5: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
D6 - DD:
DE - E4:
a. Logical address: 01 (Communication control)
40:
b. Logical address: 61 (Cassette tape player's switch)
42 - 48:
c. Logical address: 63 (In-dash CD changer)
4. NAVIGATION ECU (Physical address: 178)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting the engine.
- *2: When 210 Sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
- *3: This code may be stored when the engine key is turned 1 min. again after engine start.
- *4: This code may be stored when the engine key is turned again after engine start.
D6 - E3:
DF - E4:
a. Logical address: 01 (Communication control)
10 - 44:
b. Logical address: 80 (Navigation ECU)
11 - 45:
c. Logical address: 80 (GPS receiver)
5. STEREO COMPONENT AMPLIFIER (Physical address: 440)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code may be stored when the engine key is turned again 1 min. after engine start.
- *3: This code may be stored when the engine key is turned again after engine start.
- *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
D6 - E1:
E2 - E3:
Logical address: 01 (Communication control)
6. STEREO COMPONENT TURNER (Physical address: 1F0)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code may be stored when the engine key is turned again 1 min. after engine start.
- *3: This code may be stored when the engine key is turned again after engine start.
- *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
D6 - DC:
DD - E3:
Logical address: 01 (Communication control)
7. AUDIO AND REAR A/C CONTROL SWITCH (Physical address: 1C0)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code may be stored when the engine key is turned again 1 min. after engine start
- *3: This code may be stored when the engine key is turned again after engine start.
- *4: When 210 Sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
D6 - D7:
DC - E4:
Logical address: 01 (Communication control)
8. TELEPHONE ECU (Physical address :17C)
HINT:
- *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.
- *2: This code may be stored when the engine key is turned again 1 min. after engine start.
- *3: This code may be stored when the engine key is turned again after engine start.
- *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.
21 - D6:
D7 - E4:
Logical address: 01 (Communication control)