Front Seat
DISASSEMBLY1. REMOVE FRONT SEAT UNDER TRAY
Remove the 4 screws and front seat under tray.
2. REMOVE FRONT SEAT UNDER TRAY RAIL
3. REMOVE POWER SEAT SWITCH KNOBS
4. REMOVE SEAT POSITION SENSOR ASSEMBLY
Remove the bolt and seat position sensor assembly.
5. REMOVE FRONT SEAT CUSHION SHIELD
Remove the 4 screws and front seat cushion shield.
6. REMOVE SEAT CUSHION SWITCH AND POWER LUMBAR SUPPORT SWITCH
a. Disconnect the connectors.
b. Remove the 2 screws and seat cushion switch.
c. Remove the 3 screws and power lumbar support switch.
7. REMOVE FRONT SEAT HINGE COVER
Remove the 2 screws and front seat hinge cover.
8. REMOVE FRONT SEAT INNER BELT
Remove the nut and front seat inner belt.
9. REMOVE FRONT SEAT CUSHION INNER SHIELD
Remove the 3 screws and front seat cushion inner shield.
10. REMOVE FRONT SEAT CUSHION FRONT SHIELD
a. Remove the 4 screws.
b. Slide the front seat cushion front shield toward to remove it.
11. REMOVE POWER SEAT SWITCH
12. REMOVE FRONT SEATBACK BOARD
a. Remove the 2 screws.
b. Remove the front seatback board as shown in the illustration.
13. REMOVE SEATBACK ASSEMBLY
a. Climate control seat:
Remove the 3 screws and disconnect the air duct.
b. Disconnect the connectors and disengage the clamps.
c. Remove the 4 bolts and seatback assembly.
14. REMOVE HEADREST
Remove the headrest from the seatback assembly-
15. REMOVE HEADREST SUPPORTS
16. REMOVE SEATBACK FRAME
a. Remove the bolt and seat cover hook.
b. Remove the seatback frame from the seatback cover with pad.
NOTE: Do not damage the side airbag assembly.
17. REMOVE SEATBACK COVER
Remove the hog rings and seatback cover from the seatback pad.
18. REMOVE HEADREST ADJUSTER
a. Disengage the connector clamps.
b. Remove the 3 bolts and headrest adjuster from the seat-back frame.
19. Climate control seat:
REMOVE AIR DUCT
Remove the 2 screws, bracket and air duct from the seatback
20. REMOVE LUMBAR SUPPORT ADJUSTER
a. Remove the 2 bolts, lumbar support adjuster and spacer.
b. Employ the same manner described above to the other side.
21. Climate control seat:
REMOVE AIR RESERVOIR ASSEMBLY
a. Disengage the seat cushion cover hook.
b. Disconnect the connectors and disengage the connector clamps.
c. Remove the bolt and air reservoir duct.
22. REMOVE LOWER SEAT CUSHION SHIELD
Remove the 4 nuts and lower seat cushion shield.
23. REMOVE SEAT CUSHION ASSEMBLY
Remove the 4 bolts and seat cushion assembly.
24. REMOVE SEAT CUSHION FRAME
Disengage the seat cushion cover hook, then remove the seat cushion frame from the seat cushion cover with pad.
25. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat cushion pad.
26. REMOVE RECLINING ADJUSTER INSIDE COVER
a. Remove the screw and reclining adjuster inside cover.
b. Employ the same manner described above to the other side.
27. REMOVE POWER RECLINING ADJUSTER ASSEMBLY
Using a torx socket wrench, remove the 4 torx screws and power reclining adjuster assembly.
Torx socket wrench: T40 (Part No. 09042-00020 or locally manufactured tool)
28. REMOVE RECLINING MOTOR
a. Remove the 2 bolts and reclining motor assembly.
b. Remove the 2 screws and reclining motor from the bracket.
29. REMOVE TILT MOTOR
Remove the 2 screws and tilt motor.
30. REMOVE LIFTER MOTOR
Remove the 2 screws and lifter motor.
31. REMOVE NO. 1 SEAT CUSHION PLATE
Remove the 2 bolts and No. 1 seat cushion plate.
32. REMOVE SEAT CUSHION SPRING
33. REMOVE FRONT SEAT TRAVEL NO. 1 LINK
a. Remove the bolt and front seat travel No. 1 link.
b. Employ the same manner described above to the other side.
34. REMOVE SLIDE MOTOR
Remove the 2 screws and slide motor.
35. REMOVE SEAT CUSHION SLIDE MOTOR
Remove the 2 screws and seat cushion slide motor.
REASSEMBLY
1. INSTALL SLIDE MOTOR
Install the slide motor with the 2 screws.
Torque: 2.5 N.m (25 kgf.cm, 22 in.lbf)
2. INSTALL SEAT CUSHION SLIDE MOTOR
Install the seat cushion slide motor with the 2 screws.
Torque: 2.5 N.m (25 kgf.cm, 22 in.lbf)
3. INSTALL FRONT SEAT TRAVEL NO. 1 LINK
a. Install the front seat travel No. 1 link with the bolt.
b. Employ the same manner described above to the other side.
4. INSTALL SEAT CUSHION SPRING
5. INSTALL NO. 1 SEAT CUSHION PLATE
Install the No. 1 seat cushion plate with the 2 bolts.
6. INSTALL TILT MOTOR
Install the tilt motor with the 2 screws.
Torque: 2.5 N.m (25 kgf.cm, 22 in.lbf)
7. INSTALL LIFTER MOTOR
Install the lifter motor with the 2 screws.
Torque: 2.5 N.m (25 kgf.cm, 22 in.lbf)
8. INSTALL RECLINING MOTOR
a. Install the reclining motor with the 2 screws to the bracket.
b. Install the reclining motor assembly with the 2 bolts.
9. INSTALL POWER RECLINING ADJUSTER ASSEMBLY
Using a torx socket wrench, install the power reclining adjuster assembly with the 4 torx screws.
Torx socket wrench: T40 (Part No. 09042-00020 or locally manufactured tool)
Torque: 19 N.m (195 kgf.cm, 14 ft.lbf)
10. INSTALL RECLINING ADJUSTER INSIDE COVER
a. Install the reclining adjuster inside cover with the screw.
b. Employ the same manner described above to the other side.
11. INSTALL SEAT CUSHION COVER
Install the seat cushion cover with new hog rings to the seat cushion pad.
HINT: When installing hog ring, take care to prevent wrinkles as much as possible.
12. INSTALL SEAT CUSHION FRAME
Set the seat cushion frame to the seat cushion cover with pad, then engage the seat cushion cover hooks.
13. INSTALL SEAT CUSHION ASSEMBLY
Install the seat cushion assembly with the 4 bolts.
Torque: 21 N.m (214 kgf.cm, 15 ft.lbf)
14. INSTALL LOWER SEAT CUSHION SHIELD
Install the lower seat cushion shield with the 4 nuts.
15. Climate control seat:
INSTALL AIR RESERVOIR ASSEMBLY
a. Install the air reservoir assembly with the bolt.
b. Connect the connectors and engage the connector clamps.
c. Engage the seat cushion cover hook.
16. INSTALL LUMBAR SUPPORT ADJUSTER
a. Install the lumbar support adjuster and spacer with the 2 bolts.
Torque: 5.2 N.m (54 kgf.cm, 47 in.lbf)
b. Employ the same manner described above to the other side.
17. Climate control seat:
INSTALL AIR DUCT
Install the air duct and bracket with the 2 screws to the seatback frame.
18. INSTALL HEADREST ADJUSTER
a. Install the headrest adjuster with the 3 bolts to the seat-back frame.
Torque: 5.2 N.m (54 kgf.cm, 47 in.lbf)
b. Engage the connector clamps.
19. INSTALL SEATBACK COVER
Install the seatback cover with now hog rings to the seatback pad.
20. INSTALL SEATBACK FRAME
a. Install the seatback frame to the seatback cover with pad.
b. Install the seatback cover hook with the bolt.
Torque: 5.2 N.m (54 kgf.cm, 47 in.lbf)
NOTE: Do not damage the side airbag assembly.
21. INSTALL HEADREST SUPPORTS
22. INSTALL HEADREST
Install the headrest to the seatback assembly.
23. INSTALL SEATBACK ASSEMBLY
a. Install the seatback assembly with the 4 bolts.
Torque: 43 N.m (440 kgf.cm, 32 ft.lbf)
b. Connect the connectors and engage the clamps.
c. Climate control seat:
Connect the air duct and install it with the 3 screws.
24. INSTALL SEATBACK BOARD
Install the seatback board as shown in the illustration, then install the 2 screws.
25. INSTALL POWER SEAT SWITCH
26. INSTALL FRONT SEAT CUSHION FRONT SHIELD
Slide the front seat cushion front shield rearward, then install it with the 4 screws.
27. INSTALL FRONT SEAT CUSHION INNER SHIELD
Install the front seat cushion inner shield with the 3 screws-
28. INSTALL FRONT SEAT INNER BELT
Install the front seat inner belt with the nut.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
29. INSTALL FRONT SEAT HINGE COVER
Install the front seat hinge cover with the 2 screws to the front seat cushion shield.
30. INSTALL SEAT CUSHION SWITCH AND POWER LUMBAR SUPPORT SWITCH
a. Install the seat cushion switch with the 2 screws.
b. Install the power lumbar support switch with the 3 screws.
c. Connect the connectors.
31. INSTALL FRONT SEAT CUSHION SHIELD
Install the front seat cushion shield with the 4 screws.
32. INSTALL SEAT POSITION SENSOR ASSEMBLY
Install the seat position sensor assembly with a new bolt.
Part No. : 90119-06871
Torque: 8.0 N.m (82 kgf.cm, 71 in.lbf)
NOTE:
- Make sure the sensor assembly is installed with the specified torque.
- If the sensor assembly has been dropped, or there are cracks, dents or other defects in the case, bracket or connector, replace the sensor assembly with a new one.
- When installing the sensor assembly, take care that the SRS wiring does not interfere with other parts and is not pinched between other parts.
- After installation, shake the sensor assembly to check that there is no looseness.
33. INSTALL POWER SEAT SWITCH KNOBS
34. INSTALL FRONT SEAT UNDER TRAY RAIL
35. INSTALL FRONT SEAT UNDER TRAY
Install the front seat under tray with the 4 screws.