Replacement Procedure
Indoor Electrical Key Oscillator (Front)HINT:
^ The installation procedures are the removal procedures in reverse order.
^ A bolt without a torque specification is shown in the standard bolt chart.
1. Remove Instrument Cluster Finish Panel Center Lower.
A. Using a screwdriver, disengage the 2 claws and remove the instrument cluster finish panel center lower.
HINT:
If using a screwdriver to remove panels, secure by clips, make sure to cover tip with tape.
2. Remove Instrument Cluster Finish Panel End.
A. Using a screwdriver, disengage the 2 claws and the clip. Then, remove the instrument cluster finish panel end.
3. Remove Instrument Panel Under Cover Sub-Assembly No. 1.
A. Remove the 2 screws
B. Disengage the 2 clips and remove the instrument panel under cover Sub-Assembly No. 1.
C. Disconnect the connectors.
4. Remove Coin Box Assembly.
A. Pull the parking brake and remove the 2 nuts
B. Using a moulding remover, disengage the 2 claws and remove the coin box assembly.
C. Disconnect the connector.
5. Remove Outer Mirror Switch Assembly.
A. Using a moulding remover, disengage the 2 claws and remove the outer mirror switch assembly.
B. Disconnect the connectors.
6. Remove Instrument Panel Safety Pad Sub-Assembly No. 1.
A. Remove the 2 bolts and the screw
B. Remove the 2 bolts and the hood lock control cable assembly.
C. Disengage the 4 clips and remove the instrument panel safety pad Sub-Assembly No. 1.
D. Disconnect the connectors.
7. Remove Instrument Panel Airbag Assembly Lower No. 1.
8. Remove Instrument Panel Under Cover Sub-Assembly No. 2.
A. Disengage the 4 clips and the 2 claws. Then, remove the instrument panel under cover Sub-Assembly No. 2.
B. Disconnect the connector.
9. Remove Instrument Panel Garnish Sub-Assembly RH.
A. Using a moulding remover, disengage the 4 clips and remove the instrument panel garnish Sub-Assembly RH.
10. Remove Glove Compartment Plate.
11. Remove Glove Compartment Hole Cover.
A. Disengage the 6 claws and remove the glove compartment hole cover.
12. Remove Glove Compartment Door Assembly with Instrument Panel Airbag Assembly Lower No. 2.
A. Remove the 3 bolts
Torque: 10 N.m (102 kgf.cm, 7 ft.lbf).
B. Disengage the clip and remove the glove compartment door assembly with instrument panel airbag assembly lower No. 2.
C. Disconnect the connectors.
13. Remove Instrument Panel Finish Panel Lower Center.
A. Using a moulding remover, disengage the 2 clips and remove the instrument panel finish panel lower center.
B. Disconnect the connector.
14. Remove Panel Instrument Cluster Finish Lower.
A. Remove the 3 screws
B. Using a moulding remover, disengage the 2 clips and remove the panel instrument cluster finish lower.
C. Disconnect the connectors.
15. Remove Radio Receiver Assembly with Bracket.
16. Remove Shift Lever Knob Sub-Assembly.
A. Turn the shift lever knob Sub-Assembly counterclockwise and remove the shift lever knob Sub-Assembly.
17. Remove Console Panel Sub-Assembly Upper.
A. Using a moulding remover, disengage the 4 clips and remove the console panel Sub-Assembly upper.
B. Disconnect the connector.
18. Remove Console Upper Rear Panel Sub-Assembly.
A. Using a screwdriver, disengage the 4 claws and remove the console upper rear panel Sub-Assembly.
19. Remove Console Box Carpet.
20. Remove Rear Console Armrest Assembly.
A. Remove the 2 bolts
B. Slide the inner tray forward and remove the 4 bolts
C. Disconnect the connectors.
D. Disengage the 2 clips and remove the rear console armrest assembly.
21. Remove Console Box.
A. Remove the 2 bolts
B. Disconnect the connector and remove the console box.
22. Remove Indoor Electrical Key Oscillator (Front).
A. Remove the 2 screws
B. Disconnect the connector and remove the indoor electrical key oscillator (front).
Door Electrical Oscillator (Rear)
HINT:
The installation procedures are the removal procedures in reverse order.
1. Remove Rear Seat Cushion Assembly (Fixed Type).
A. Pull up the 3 front portions of the seat cushion, then remove it.
NOTE:
The cushion frame deforms easily. To avoid deforming the seat cushion, place your hands near the hook and on both sides of the hook. Then pull up on the seat cushion. For all the other hooks, perform the same operation.
B. With seat heater:
Disconnect the connector.
2. Remove Rear Seat Cushion Assembly RH (Power Adjuster Type).
A. Pull up the 2 front portions of the seat cushion, then remove it.
NOTE:
The cushion frame deforms easily. To avoid deforming the seat cushion, place your hands near the hook and on both sides of the hook. Then pull up on the seat cushion. For all the other hooks, perform the same operation.
B. With seat heater or climate control seat system:
Disconnect the connector.
3. Remove Rear Seat Cushion Assembly LH (Power Adjuster Type).
A. Pull up the 2 front portions of the seat cushion, then remove it.
NOTE:
The cushion frame deforms easily. To avoid deforming the seat cushion, place your hands near the hook and on both sides of the hook. Then pull up on the seat cushion. For all the other hooks, perform the same operation.
B. With seat heater or climate control seat system:
Disconnect the connector.
4. Remove Indoor Electrical Key Oscillator (Rear).
A. Remove the 2 bolts.
B. Disconnect the connector and remove the indoor electrical key oscillator (rear).
Indoor Electrical Key Oscillator Luggage Compartment)
Components
HINT:
The installation procedures are the removal procedures in reverse order.
1. Remove Deck Side Trim Board.
A. Remove the 4 bolts and 4 luggage compartment trim hooks No. 1.
Torque: 8.0 N.m (82 kgf.cm, 71 in.-lbf)
B. Remove the mat.
C. Using a clip remover, remove the 5 clips and rear floor finish plate.
D. Using a clip remover, remove the 2 clips and 2 deck side trim boards.
2. Remove Luggage Compartment Trim Inner Lower Cover.
A. Using a clip remover, remove the 3 clips.
B. Remove the luggage compartment trim inner lower cover.
3. Remove Indoor Electrical Key Oscillator (Luggage Compartment)
A. Remove the bolt.
B. Disconnect the connector and remove the indoor electrical key oscillator (luggage compartment).
Electrical Key Transmitter
NOTE:
Take extra care when handling these precision electronic components.
1. Remove Transmitter.
A. Using a screwdriver, pry up the outer cover.
NOTE:
Do not forcibly pry up the cover.
B. Lightly shake the key to take out the transmitter as shown in the illustration.
C. Remove the battery from old transmitter.
D. Insert battery holder into new transmitter.
NOTE:
^ Do not push the terminals with your finger.
^ Fully insert the holder into the transmitter.
NOTE:
^ Be sure that the positive side and the negative side of the transmitter battery are matched up correctly.
^ Be careful not to bend the transmitter battery electrode during insertion.
^ Keep the transmitter case interior free of dust and oil.
E. Install the outer cover.
Immobilizer Registration
1. Description of Code Registration.
A. Erasure of key code.
a. Erase the key codes.
B. When adding master key and sub-keys (additional registration).
a. Register the key code (immobilizer code) in the steering lock ECU.
b. Register the key code (smart code) in the steering lock ECU.
2. Erasure of Key Code
A. Erase key codes using the Diagnostic Tester.
HINT:
^ All key codes are erased except for the master key, which is used for erasing the key codes. In order to use a key whose code has been erased, its key code must be re-registered.
^ Registration will be cancelled if each step is not completed within the specified time.
HINT:
^ A brief outline of procedures for key code erasure is shown. For more detailed information, please refer to the Diagnostic Tester screen's instructions.
^ When the immobilizer system is operating normally and the key is pulled out, the security indicator blinks continuously.
3. Registration of Additional Key (Additional Registration)
A. Register an additional key by using the Diagnostic Tester.
HINT:
^ A maximum of 5 master key codes and 3 sub-key codes can be registered.
^ Registration mode will end if each step is not completed within the specified time.
^ When the ignition cylinder or the key cylinder set is replaced, remove the transmitter module from the original master key. Then install this transmitter module to a new key and use the new key as the master key. If necessary, use this master key to register other keys.
NOTE:
When the ignition key cylinder has been replaced, locking and unlocking doors is possible with the new master key's transmitter module (taken from the original master key). However, the new master key will not be able to lock and unlock doors through the door key cylinder. Keep the original master key. If the new master key's transmitter module's battery fails, the original master key can be used to lock and unlock doors through the door key cylinder.
HINT:
^ A brief outline of procedures for key code registration is shown. For more detailed information, please refer to the Diagnostic Tester screen's instructions.
^ When the immobilizer system is operating normally and the key is pulled out, the security indicator blinks continuously.
^ If the key code registration has failed in automatic key code registration mode, code 2-1 will be output from the security indicator. Trying to re-register an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the limit, code 2-3 will be output from the security indicator. The output details are shown in step 2 (new registration).
Smart Key/Wireless Registration
1. Wireless (Smart Key Code Registration).
A. Reset the Smart Key codes using the Diagnostic Tester.
HINT:
^ A brief outline of procedures for key code reset is shown. For more detailed information, please refer to the Diagnostic Tester screen's instruction.
^ SEED NUMBER is a 6 digit code.
^ PASS-CODE NUMBER is a 6 digit code.
^ Reset mode will take approximately 16 minutes to complete.
2. Registration of New and Additional Smart Key Codes.
A. Register a Smart Key code using the Diagnostic Tester.
HINT:
^ A brief outline of procedures for key code registration is shown. For more detailed information, please refer to the Diagnostic Tester screen's instruction.
^ The number of currently registered codes can be checked out on the first screen, "SMART (KEY) CODE REGISTRATION."