P0136
DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)CIRCUIT DESCRIPTION
Detection Item:
To obtain a high purification rate for the CO, HC and NOx components of the exhaust gas, a three-way catalytic converter is used, but for the most efficient use of the three-way catalytic converter, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel ratio.
The heated oxygen sensor has the characteristic whose output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. This characteristic is used to detect the oxygen concentration in the exhaust gas and provide the ECM with feedback to control the air-fuel ratio.
When the air-fuel ratio becomes LEAN, the oxygen concentration in the exhaust increases and the heated oxygen sensor informs the ECM of the LEAN condition (low voltage, i.e. less than 0.45 V).
When the air-fuel ratio is RICHER than the stoichiometric air-fuel ratio, the oxygen concentration in the exhaust gas is reduced and the heated oxygen sensor informs the ECM of the RICH condition (high voltage, i.e. more than 0.45 V). The ECM judges by the voltage output from the heated oxygen sensor whether the air-fuel ratio is RICH or LEAN and controls the injection time accordingly. However, if a malfunction of the heated oxygen sensor causes output of abnormal voltage, this disables the ECM to perform an accurate air-fuel ratio control. The heated oxygen sensors include a heater which heats the zirconia element. The heater is controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low) current flows to the heater to heat the sensor for accurate oxygen concentration detection.
HINT: The ECM provides a pulse width modulated control circuit to adjust current through the heater. The heated oxygen sensor heater circuit uses a relay on the B+ side of the circuit.
HINT:
- Bank 1 refers to bank that includes cylinder No.1.
- Bank 2 refers to bank that does not include cylinder No.1.
- Sensor 2 refers to the farther sensor away from the engine body.
MONITOR DESCRIPTION
Monitor Strategy:
Typical Enabling Conditions Part 1:
Typical Enabling Conditions Part 2:
Typical Malfunction Thresholds:
Component Operating Range:
O2S Test Result Part 1:
O2S Test Result Part 2:
The ECM monitors the rear heated oxygen sensor in the following 3 items:
1. If the rear heated oxygen sensor voltage changes between Rich and Lean while the vehicle is running (repeating acceleration and deceleration), the ECM interprets this as a malfunction and illuminates the MIL, and then sets a DTC.
2. If the rear heated oxygen sensor voltage does not remain at less than 0.05 V for a long period of time while the vehicle is running, the ECM interprets this as a malfunction and illuminates the MIL, and then sets a DTC.
3. If the sensor's voltage drops to below 0.2 V (extremely Lean status) immediately when the vehicle decelerates and the fuel cut is working. if not, the ECM interprets this as a sensor's response feature deterioration and illuminates the MIL, and then sets DTC.
Wiring Diagram:
CONFIRMATION DRIVING PATTERN
1. Connect the hand-held tester to the DLC3. (*1)
2. Switch the hand-held tester from the normal mode to the check mode. (*1)
3. Start the engine and let the engine idle for 60 seconds or more. (*2)
4. Drive the vehicle at 40 km/h (25 mph) or more for 40 seconds or more. (*3)
5. Let the engine idle for 10 seconds or more. (*4)
6. Perform steps 4. and 5. for 12 times.
HINT: If a malfunction exists, the MIL will light up on the multi-information display during step 6.
NOTE: If the conditions in this test are not strictly followed, a malfunction detection will not occur. If you do not have a hand-held tester, turn the ignition switch OFF after performing steps from 3 to 6, then perform steps from 3 to 6 again.
INSPECTION PROCEDURE
Step 1 - 2:
Step 3 - 5:
Step 6 - 7:
HINT:
Hand-held tester only:
Narrowing down the trouble area is possible by performing ACTIVE TEST of the following "A/F CONTROL" (Heated oxygen sensor or another can be distinguished).
a. Perform ACTIVE TEST by hand-held tester (A/F CONTROL).
HINT: "A/F CONTROL" is the ACTIVE TEST which changes the injection volume to -12.5% or +25%.
1. Connect the hand-held tester to the DLC3 on the vehicle.
2. Turn the ignition switch ON.
3. Warm up the engine with the engine speed at 2,500 rpm for approximately 90 seconds.
4. Select the menu "DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL".
5. Perform "A/F CONTROL" with the engine in an idle condition (press the right or left button).
RESULT:
Heated oxygen sensor reacts in accordance with increase and decrease of injection volume
+25% -> rich output: More than 0.5 V
-12.5% -> lean output: Less than 0.4 V
There is a few seconds delay in the sensor 1 (front sensor) output. And there is approximately 20 seconds delay in the sensor 2 (rear sensor).
The following A/F CONTROL procedure enables the technician to check and graph the voltage output of the heated oxygen sensors.
For displaying the graph indication, first enter "ACTIVE TEST / A/F CONTROL / USER DATA," then select "02S B1S1and O2S B1S2" by pressing "YES" button, and push "ENTER" button before pressing "F4" button
HINT:
- If different DTCs that are related to different system are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may be open.
- Read freeze frame data using the hand-held tester or the OBD II scan tool. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean or rich, etc. at the time of the malfunction.
CHECK FOR INTERMITTENT PROBLEMS
Hand-held tester only:
Inspect the vehicle's ECM using check mode. Intermittent problems are easier to detect when the ECM is in check mode with hand-held tester. In check mode, the ECM uses 1 trip detection logic, which has a higher sensitivity to malfunctions than normal mode (default), which uses 2 trip detection logic.
a. Clear the DTCs (see step 2).
b. Set the check mode (see step 3).
c. Perform a simulation test.
d. Check the connector and terminal.
e. Wiggle the harness and connector.