Pre-Check

PRE-CHECK

1. DIAGNOSIS SYSTEM MODE






HINT: Diagnosis System Mode is operated as follows.

a. DIAGNOSIS START-UP
To start the diagnosis menu, there are 3 ways: using a diagnosis check wire and using a switch.




b. START-UP BY SWITCH OPERATION
(light control switch)
1. Vehicle speed is 0 km/h (0 mph).
2. Parking brake switch is pressed.
3. While pressing "INFO" switch, by turning the light control switch to OFF, TAIL, OFF, TAIL, and OFF the system is started up.

c. START-UP BY SWITCH OPERATION (touch panel)
1. Vehicle speed is 0 km/h (0 mph).
2. Parking brake switch is pressed.
3. Press the "INFO" switch to display the Screen Adjustment screen.




4. Repeatedly touch the upper and lower bottom parts of the screen 3 times.

d. FINISHING DIAGNOSIS SYSTEM MODE
Turn the ignition switch from ACC to OFF to finish the mode. If it is started by switch operation.

2. SERVICE CHECK MODE






HINT: Service Check Mode is operated as follows.




a. Service Check Mode




1. Start the Diagnosis System.

HINT: Service Check displays the check results based on the information obtained from each component's response to "System Check Execution" and "Diagnosis Memory Request", and the information of "Current DTC Notification" (the Unit Check and the LAN Check information that will be displayed on the next screens.).




2. Read Check Result

HINT:
- After repair and check, press "Code CLR" for more than 3 sec. to delete diagnosis memory.
- After deleting diagnosis memory, press "Recheck" and make sure "OK" is displayed on the screen.










3. "EXCH", "CHEK" and "Old" can be used as switches to activate "LAN Check Mode" and "Unit Check Mode" for detail information. Check troubled parts of the components in these modes by referring to the DTC code list.

HINT:
- Detecting Unit DTC activates the Unit Check Mode on the screen.
- Detecting no LAN DTC activates the LAN Check Mode on the screen.
- Use the displayed switch to change to the Unit Check Mode and the LAN Check Mode.
- The LAN Check Mode chooses and displays the LAN DTC out of DTC of components identified as "CHEK" in the Service Check.
- In the Unit Check Mode, DTC which is identified as "EHCK" in the Service Check, is displayed as classified into Current DTC and Past DTC.

3. DISPLAY CHECK MODE






HINT: Display Check Mode is operated as follows







a. Display Check Mode

HINT: In Display Check Mode, checks can be performed.




b. Display Color Bar Check
1. Start the Diagnosis System.
2. Select "MENU".
3. Select "Display Check".
4. Select "Color Bar Check".
5. Make sure that each color name is corresponding to each color on the bar.

HINT: Select Black, Red, Green, Blue, White and Stripe to display selected colors and stripe on the entire screen.

6. Compare with the Color Bar Check in the Navigation Check and make sure that no difference is found.




c. Display Touch Switch Check
1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Display Check".
4. Select "Touch Switch Check".
5. Touch the screen and make sure that every line reacts to the touch.

HINT: After the Touch Switch Check for vertical lines, press "Next" to check horizontal lines.




d. Display Panel Switch Check
1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Display Check".
4. Select "Panel Switch Check".




5. Press each switch and make sure that it corresponds to the display on the screen.




e. Display Vehicle Signal Check
1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Display Check".
4. Select "Vehicle Signal Check".
5. Check the status of the vehicle signal (Battery, IG, PKB, SPEED, TAIL, ADIM/TCAN) loaded into the display.

HINT: Vehicle signal data is updated every 1 second.

4. NAVIGATION CHECK MODE




HINT: Navigation Check Mode is operated as follows.







a. Navigation Check Mode

HINT:
- In the Navigation Check mode, the checks mentioned can be conducted.
- The Navigation ECU operates each Navigation Check screen.













b. GPS Information
1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Navigation Check".
4. Select "GPS Information".
5. Check the GPS-related information.




c. Vehicle Sensors
1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Navigation Check".
4. Select "Vehicle sensors".




5. Check the vehicle signals (ACC, REV, SPD) and the output signal of the gyro sensor introduced into the navigation ECU.




d. Navigation Color Bar Check
1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Navigation Check".
4. Select "Color Bar Check".
5. Make sure that the set color matches the display color.
6. Compare with the Color Bar Check in the Display Check and make sure that no difference is found.




e. Parts Information
1. Start the Diagnosis system.
2. Select "MENU".
3. Select "Navigation Check".
4. Select "Parts Information".
5. Check the program and disc version.




f. Memory/ Copy/ Paste

HINT: This function is not available.