Power Mirror Control System
ON-VEHICLE INSPECTION1. CHECK POWER MIRROR SWITCH OPERATION OF INTEGRATION CONTROL AND PANEL ASSEMBLY
a. Turn the engine switch on (ACC).
b. When the L mirror master switch is pressed, check that the indicator light on the LH side illuminates.
c. With the mirror master switch set to L, check that the mirror surface moves UP, DOWN, LEFT and RIGHT normally.
d. After checking the mirror surface movement, check that pressing the L mirror master switch causes the indicator light on the LH side to turn off.
e. When the R mirror master switch is pressed, check that the indicator light on the RH side illuminates.
f. With the mirror master switch set to R, check that the mirror surface moves UP, DOWN, LEFT and RIGHT normally.
g. After checking the mirror surface movement, check that pressing the R mirror master switch causes the indicator light on the RH side to turn off.
2. CHECK MEMORY AND REACTIVATION FUNCTION
a. Turn the engine switch on (IG) and move the shift lever into the P position.
b. Check the M1 switch.
1. Using the mirror master switch and mirror control switch, fully turn the mirror to the left.
2. Press and hold down switches M1 and SET. Check that the buzzer sounds for 0.5 seconds, signaling that the outer mirror position has been recorded.
3. Change the position of the outer mirror and then press the M1 switch. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully-turned-left position.
c. Check the M2 switch.
1. Using the mirror master switch and mirror control switch, fully turn the mirror to the right.
2. Press and hold down switches M2 and SET. Check that the buzzer sounds for 0.5 seconds, signaling that the outer mirror position has been recorded.
3. Change the position of the outer mirror and then press the M2 switch. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully-turned-right position.
d. Check the M3 switch.
1. Using the mirror master switch and mirror control switch, fully turn the mirror upward.
2. Press and hold down switches M3 and SET. Check that the buzzer sounds for 0.5 seconds, signaling that the outer mirror position has been recorded.
3. Change the position of the outer mirror and then press the M3 switch. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully-upward position.
e. When the outer mirror is in the driving position: Check that switches M1, M2 and M3 cause the outer mirror to move to the recorded outer mirror positions under these conditions: turn the engine switch off, open the driver side door and press M1, M2 or M3 within 30 seconds.
f. Check that the following procedures will erase the recorded outer mirror positions of switches M1, M2 and M3: press and hold the power seat slide switch; disconnect the battery's negative (-) terminal cable; and wait for at least 1 minute.
g. Check that all recorded outer mirror positions are erased. Attempt to record a seat position by pressing and holding the SET switch and two other switches (among M1, M2 and M3). No outer mirror position should be recorded. Check this by pressing M1, M2 or M3 and making sure that the outer mirror does not move.
3. CHECK POWER RETRACTABLE MIRROR
a. Turn the engine switch on (ACC).
b. At each position of the outer mirror body, check the retractable mirror's operation when operating the retract switch of the outer mirror.
1. Move the mirrors to the driving position.
2. Press the retract switch.
3. Check that the right and left mirrors move from the driving position to the retracted position.
4. Move the mirrors to the driving position.
5. Move one of the mirrors to the forward position by hand.
6. Press the retract switch.
7. Check that the mirror moves from the forward position to the retracted position.
8. Check that the other mirror moves from the driving position to the retracted position.
9. Move the mirrors to the driving position.
10. Move one of the mirrors to the retracted position by hand.
11. Press the retract switch.
12. Check that the outer mirror moves from the driving position to the retracted position.
13. Move the mirrors to the retracted position.
14. Press the retract switch.
15. Check that the right and left mirrors move from the retracted position to the driving position.
16. Move the mirrors to the retracted position.
17. Move one of the mirrors to the driving position by hand.
18. Press the retract switch.
19. Check that the other mirror moves from the retracted position to the driving position.
c. Check the operation of the outer mirror body in relation to retract switch operations and engine switch position changes.
1. When the mirror body is operating, turn the engine switch off. Check that the mirror operation does not stop and continues until the operation has finished.
2. Repeat the step above. This time, before the mirror operation completes, turn the engine switch on (ACC) and press the retract switch. Check that the mirror operates in the opposite direction.
d. Check the operation of the outer mirror body when it is restrained by an obstacle.
1. When the mirror body is moving to the retracted or driving position, restrain the mirror body by hand. Check that the mirror body stops moving.
2. With the mirror body stopped partway, push the retract switch. Check that the mirror body moves in the opposite direction.
4. CHECK REVERSE-SHIFT-LINKED OPERATION OF MIRRORS
a. Turn the engine switch on (IG).
b. Set the mirror master switch to L or R.
c. Check that the mirror faces downward when the shift lever is moved to R.
d. When the shift lever is not on P, or the mirror master switch is in the neutral position (OFF), check that the outer rear view mirror returns to the driving position.
5. CHECK MIRROR HEATER
a. Turn the engine switch on (IG).
b. Check that pressing the rear defogger switch illuminates the indicator and warms the mirror surface.
c. Check that after approximately 15 minutes, the indicator light turns off and the mirror heater deactivates.