Front Seat Assembly
FRONT SEAT ASSEMBLYFront Seat Assembly:
Front Seat Assembly:
Front Seat Assembly:
Front Seat Assembly:
Front Seat Assembly:
Front Seat Assembly:
Front Seat Assembly:
Front Seat Assembly:
REMOVAL
(2006/02-2006/07)
HINT: Use the same procedures for the LH and RH side.
1. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY
a. Using a screwdriver, detach the 2 claws and remove the front seat belt hole cover.
HINT: Tape the screwdriver tip before use.
b. Apply protective tape to the cushion shield around the seat belt anchor cover cap.
c. Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.
HINT: Tape the screwdriver tip before use.
d. Operate the power seat switch knob and move the seat to the foremost position.
e. Move the seat using the power seat switch knob so that the seat belt anchor bolt is revealed.
f. Remove the bolt and front seat outer belt anchor.
2. REMOVE FRONT SEAT ASSEMBLY
a. Operate the power seat switch knob and move the seat to the rearmost position.
b. Using a screwdriver, detach the 4 claws and remove the seat track bracket cover front inner and outer.
HINT: Tape the screwdriver tip before use.
c. Remove the 2 bolts on the front side of the seat.
d. Operate the power seat switch knob and move the seat to the foremost position.
e. Using a screwdriver, detach the 4 claws and remove the seat track bracket cover rear inner and outer.
f. Remove the 2 bolts on the rear side of the seat.
g. Disconnect the cable from the negative (-) battery terminal.
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
h. Disconnect the connectors under the seat. Then remove the seat.
REMOVAL
(2006/07- )
HINT: Use the same procedures for the LH and RH side.
1. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY (for Front Driver Side)
a. Using a screwdriver, detach the 2 claws and remove the front seat belt hole cover.
HINT: Tape the screwdriver tip before use.
b. Apply protective tape around the seat belt anchor cover cap to the cushion shield.
c. Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.
HINT: Tape the screwdriver tip before use.
d. Move the seat using the power seat switch knob so that the seat belt anchor bolt is revealed.
e. Remove the bolt and front seat outer belt anchor.
2. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY (for Front Passenger Side)
a. Using a screwdriver, detach the 5 claws and remove the front seat wire connecting plate.
HINT: Tape the screwdriver tip before use.
b. Move the seat using the power seat switch knob so that the seat belt anchor bolt is revealed.
c. Remove the bolt and front seat outer belt anchor.
d. Disconnect the connector.
3. REMOVE FRONT SEAT ASSEMBLY
a. Operate the power seat switch knob and move the seat to the rearmost position.
b. Using a screwdriver, detach the 4 claws and remove the seat track bracket cover front inner and outer.
HINT: Tape the screwdriver tip before use.
c. Remove the 2 bolts on the front side of the seat.
d. Operate the power seat switch knob and move the seat to the foremost position.
e. Using a screwdriver, detach the 4 claws and remove the seat track bracket cover rear inner and outer.
f. Remove the 2 bolts on the rear side of the seat.
g. Disconnect the cable from the negative (-) battery terminal.
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
h. Disconnect the connectors under the seat. Then remove the seat.
INSTALLATION
(2006/02-2006/07)
HINT: Use the same procedures for the LH and RH side.
1. INSTALL FRONT SEAT ASSEMBLY
a. Place the seat in the cabin.
b. Connect the connectors under the seat.
c. Connect the cable to the negative (-) battery terminal.
d. Operate the power seat switch knob and move the seat to the foremost position.
e. Install the 2 bolts on the rear side of the seat.
Torque: 36.8 N.m (375 kgf.cm, 27 ft.lbf)
HINT: Tighten the 2 bolts in the order indicated in the illustration.
f. Attach the 4 claws to install the seat track bracket cover rear inner and outer.
g. Operate the power seat switch knob and move the seat to the rearmost position.
h. Install the 2 bolts on the front side of the seat.
Torque: 36.8 N.m (375 kgf.cm, 27 ft.lbf)
HINT: Tighten the 2 bolts in the order indicated in the illustration.
i. Attach the 4 claws to install the seat track bracket cover front inner and outer.
2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY
a. Operate the power seat switch knob and move the seat to the foremost position.
b. Move the seat using the power seat switch knob so that the seat belt anchor bolt is revealed.
c. Install the front seat outer belt anchor with the bolt.
Torque: 42 N.m (428 kgf.cm, 31 ft.lbf)
d. Install the seat belt anchor cover cap.
e. Install the front seat belt hole cover.
3. PERFORM INITIALIZATION
a. Perform initialization.
NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
4. CHECK SRS WARNING LIGHT
a. Check the SRS warning light.
5. INSPECT FRONT SEAT ASSEMBLY
a. Check the power seat operation.
b. Check the seat heater operation (with seat heater).
1. Turn the power switch ON (IG).
2. Turn the seat heater switch ON.
3. Wait 5 minutes or more and confirm that the seat surface becomes warm.
INSTALLATION
(2006/07- )
HINT: Use the same procedures for the LH and RH side.
1. INSTALL FRONT SEAT ASSEMBLY
a. Place the seat in the cabin.
b. Connect the connectors under the seat.
c. Connect the cable to the negative (-) battery terminal.
d. Operate the power seat switch knob and move the seat to the foremost position.
e. Tighten the 2 bolts on the rear side of the seat.
Torque: 36.8 N.m (375 kgf.cm, 27 ft.lbf)
HINT: Tighten the 2 bolts in the order indicated in the illustration.
f. Operate the power seat switch knob and move the seat to the rearmost position.
g. Tighten the 2 bolts on the rear side of the seat.
Torque: 36.8 N.m (375 kgf.cm, 27 ft.lbf)
HINT: Tighten the 2 bolts in the order indicated in the illustration.
2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY (for Front Driver Side)
a. Move the seat using the power seat switch knob so that the seat belt anchor bolt is revealed.
b. Install the front seat outer belt anchor with the bolt.
Torque: 42 N.m (428 kgf.cm, 31 ft.lbf)
c. Attach the 2 claws to install the front seat wire connecting plate.
3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY (for Front Passenger Side)
a. Move the seat using the power seat switch knob so that the seat belt anchor bolt is revealed.
b. Connect the connector.
c. Install the front seat outer belt anchor with the bolt.
Torque: 42 N.m (428 kgf.cm, 31 ft.lbf)
d. Attach the 5 claws to install the front seat wire connecting plate.
4. PERFORM INITIALIZATION
Perform initialization.
NOTICE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
5. CHECK SRS WARNING LIGHT
Check the SRS warning light.
6. INSPECT FRONT SEAT ASSEMBLY
a. Check the power seat operation.
b. Check the seat heater operation (w/ seat heater).
1. Turn the engine switch on (IG).
2. Turn the seat heater switch ON.
3. Wait 5 minutes or more and confirm that the seat surface becomes warm.