Navigation System - HDD Navigation Map Update Procedure

SPECIAL SERVICE TOOLS
SS007-07
REVISED

Title:
HDD NAVIGATION MAP
UPDATE PROCESS

Models:
'07 - '08 LS 460/460L & LS 600h
& '08 LX 570

October 26, 2007

TSB REVISION NOTICE:
^ January 31, 2008: 2008 model year LX 570 has been added to Applicable Vehicles.

Previous versions of this TSB should be discarded.

Introduction

Lexus models equipped with Hard Disk Drive (HDD) Navigation require a Special Service Tool and follow a unique process for updating map, points of interest, and system software. Instead of individual DVDs installed into the vehicle, all Map Data is uploaded directly to the HDD system.

Map Data will be released annually through the direct shipment of two Map Data DVDs to each dealership service manager. The annual Map Data release must then be installed onto the Navigation Update Tool. Individual map updates are then loaded into vehicles with special map security keys. These keys are available through the normal parts ordering system. Keys are loaded onto the Navigation Update Tool through a PC or TIS techstream unit using software found on the Technical Information System (TIS).

Follow the procedures listed in this bulletin to:

^ Identify the current version of Map Data on the vehicle and on the Navigation Update Tool.

^ Load Map Data onto the Navigation Update Tool.

^ Load map security key(s) onto the Navigation Update Tool.

^ Connect the Navigation Update Tool to the vehicle and update the Map/System Data to the latest version.

^ In order to perform the procedures outlined in this TSIB, you MUST have completed the setup procedure in TSIB No. SS003-07, "HDD Navigation Program Setup".

^ Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives, cameras, mice, etc.).

^ For additional details, refer to the Navigation Update Tool Operator's Manual on TIS.

Applicable Vehicles

^ 2007 - 2008 model year LS 460/460L vehicles.

^ 2008 model year LS 600h vehicles.

^ 2008 model year LX 570 vehicles.

Warranty Information

Parts Information

Required Materials

Required Tools & Equipment

Version Verification

Before performing a Map update, verify the version of Map Data on the Navigation

Update Tool and on the vehicle's Navigation System.

Check Map Data version on Navigation Update Tool:

1. Open the Navigation Programs Installer.

^ When properly installed, the Navigation Programs Installer icon will be found on the TIS techstream desktop.

^ If the application is NOT properly installed, refer to TSIB No. SS003-07, "HDD Navigation Program Setup".

2. Click Version Check.

3. Connect the Navigation Update Tool.

A. Make sure the USB cable is secured in both the PC and the Navigation Update Tool USB ports.

B. Confirm that the Navigation Update Tool is powered correctly.

C. Turn power ON.

D. Press Continue.

4. Compare the Map version with the Map version shown on the DVD.

^ If the Map version on the Navigation Update Tool is the same as shown on the DVD, then go to the "Security Key Load" section in this TSIB.

^ If the Map version on the Navigation Update Tool is NOT the same as shown on the DVD, then go to the "Tool Load" section in this TSIB.

Check Map Data version on Vehicle HDD Navigation System:

Prior to connecting to the vehicle you MUST disconnect navigation update tool from the PC.

1. Connect the Navigation Update Tool to vehicle.

A. Make sure 1EEE1394 cable is secured in both the Navigation Update Tool and the vehicle connector.

B. Confirm that the Navigation Update Tool is powered correctly.

C. Turn power ON.

2. Turn vehicle ignition ON (engine OFF).

3. From the multi-information display, press / Agree.

4. Press the "MENU" button.

5. From the multi-information display, press HDD Data.

6. Compare the Map Data version on the Navigation System to that on the Navigation Update Tool.

^ If the Map version on the Navigation System is the same as shown on the navigation update tool, then the vehicle does NOT need the update.

^ If the Map version on the Navigation System is NOT the same as shown on the navigation update tool, then go to the "Tool Load" section in this TSIB.

Tool Load

NOTE:
There are three separate processes used to update the Map Data on the vehicle:

^ Loading the Map Data onto the Navigation Update Tool

^ Loading the Map Data security key onto the Navigation Update Tool

^ Loading the Map Data into the vehicle HDD Navigation System

If the Map version on the Navigation Update Tool is the same as shown on TIS, then go to the "Security Key Load" section in this TSIB.

If the Map version on the Navigation Update Tool is NOT the same as shown on TIS, then follow the instructions below.

Loading Map Data onto Navigation Update Tool

NOTE:
Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives, cameras, mice, etc.).

3. Connect the Navigation Update Tool.

A. Make sure the USB cable is secured in both the PC and the Navigation Update Tool USB ports.

B. Confirm that the Navigation Update Tool is powered correctly.

C. Turn power ON.

D. Press Continue.

4. Insert Map Disk 1 into the CD/DVD-ROM drive.

5. Allow Map Data to copy onto the PC hard drive (requires about 20minutes).

If necessary:

^ Insert the additional Map Disk as instructed into the CD/DVD-ROM drive.

^ Allow the additional Map Data to copy onto the PC hard drive (requires about 20 minutes).

2. Select Load key File.

4. Connect USB Key File and press Continue.

5. Click Load to continue.

6. Allow the Key File to copy onto the Navigation Update Tool (requires about 5 seconds).

7. Verify the Key File is loaded onto the Navigation Update Tool and can now be used to update the vehicle.

NOTE:

^ The Navigation Update Tool will hold up to ten security keys. One key is required per vehicle update.

^ Storing keys on the Navigation Update Tool is NOT recommended.

Vehicle Load

Loading Map Data onto vehicle HDD Navigation System

^ The Map Data security key MUST be loaded onto the Navigation Update Tool before Map Data can be loaded to the vehicle.

^ Prior to connecting to the vehicle you MUST disconnect navigation update tool from the PC.

^ Connect the battery charger to the vehicle prior to beginning process to ensure constant battery voltage.

1. Connect the Navigation Update Tool to the vehicle.

A. Make sure the 1EEE1394 cable is secured in both the Navigation Update Tool and the vehicle connector.

B. Confirm the Navigation Update Tool is powered correctly.

C. Turn power ON.

2. Turn vehicle ignition ON (engine OFF).

3. From the multi-information display, press I Agree.

4. Press the "MENU" button.

5. From the multi-information display, press HDD Data.

6. Press Map Data Update.

7. Press I Agree.

8. Allow Map Data to copy (requires about 25 minutes).

9. Press OK.

10. Disconnect the Navigation Update Tool from the vehicle.