Installation

SEAT: REAR SEAT ASSEMBLY (for Power Seat): INSTALLATION

INSTALLATION
CAUTION: Wear protective gloves. Sharp areas on the seatback spring, seat adjuster and seat cushion spring may injure your hands.
NOTE: If the position control ECU and rear seat adjuster is replaced, or the initialization cancel operation is performed, the position sensor initialization must be performed Rear Power Seat Control System.
HINT: A bolt without a torque specification is shown in the standard bolt chart Standard Bolt - Specified Torque For Standard Bolts.

1. INSTALL REAR SEATBACK ADJUSTER ASSEMBLY LH
(a) Install the seatback adjuster with the 4 nuts.
Torque: 20 Nm (204 kgf-cm, 15 ft-lbf)
NOTE: Be careful not to damage the vehicle body.

2. INSTALL REAR SEATBACK ADJUSTER ASSEMBLY RH
HINT: Use the same procedures described for the LH side.

3. INSTALL REAR NO. 2 SEAT ADJUSTER ASSEMBLY
(a) Install the seat adjuster with the 4 bolts and nut.
for bolt A - Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
for except bolt A - Torque: 20 Nm (204 kgf-cm, 15 ft-lbf)
NOTE: Be careful not to damage the vehicle body.

(b) Install the air duct to the vehicle body.
4. INSTALL REAR NO. 1 SEAT ADJUSTER ASSEMBLY
HINT: Use the same procedures described for the No. 2 seat adjuster.

5. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
(a) Install the floor end of the rear center seat outer belt assembly with the nut.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTE: Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

6. INSTALL REAR CENTER SEATBACK ASSEMBLY

(a) Connect the connector.
(b) Install the seatback center with the 2 bolts and nut.
Torque: 20 Nm (204 kgf-cm, 15 ft-lbf)
NOTE: Be careful not to damage the vehicle body.

(d) While pressing the button, lower the headrest.
(e) Raise the center armrest.
7. INSTALL REAR SEATBACK ASSEMBLY LH

(a) Install the rear seatback assembly to the rear seat reclining adjuster assembly.
NOTE: Be careful not to damage the vehicle body.

(b) Lift the lower part of the rear seatback assembly towards the front of the vehicle, and connect the air duct to the vehicle.
(c) Connect the rear seatback assembly to the rear No. 2 seat adjuster. Then install the rear seatback assembly with the 2 nuts.
Torque: 20 Nm (204 kgf-cm, 15 ft-lbf)

(d) Install the rear clip on the top of the seatback, and attach the 3 pieces of fastening tape.

(e) Connect the connectors and 7 wire harness clamps.

(f) Connect the 2 connectors.
(g) Install the connector holder with the bolt.

(h) Install the seat belt to the seat belt guide.
(i) Attach the 2 claws.

(j) Install the floor end of the rear seat outer belt assembly with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
NOTE: Do not allow the anchor part of the rear seat 3 point type belt assembly to overlap the protruding parts of the floor panel.

8. INSTALL REAR SEATBACK ASSEMBLY RH
HINT: Use the same procedures described for the LH side.

9. INSTALL REAR CENTER SEAT CUSHION ASSEMBLY
(a) Attach the hook to install the seat cushion.
NOTE: Be careful not to damage the vehicle body.

10. INSTALL REAR SEAT CUSHION ASSEMBLY LH
(a) Install the seat cushion.
NOTE: Be careful not to damage the vehicle body.

(b) Connect the connector.
(c) Attach the 2 front hooks of the seat cushion to the seat adjuster.
11. INSTALL REAR SEAT CUSHION ASSEMBLY RH
HINT: Use the same procedures described for the LH side.

12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

13. INSTALL BATTERY SERVICE HOLE COVER LH Battery

14. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

15. CHECK SRS WARNING LIGHT
(a) Check the SRS warning light Diagnosis System.
16. INSPECT REAR SEAT ASSEMBLY
(a) Check the power seat operation Rear Power Seat Control System.
(b) Check the climate control seat system Climate Control Seat System.