Navigation System - HDD System Program Setup
L-SB-0180-09December 4, 2009
HDD Navigation Program Setup
Service Category
Audio/Visual/Telematics
Section
Navigation/Multi Info Display
Market
USA
Applicability
TSIB SUPERSESSION NOTICE
The information contained in this TSIB supersedes TSIB No. L-SB-0042-08.
^ Applicability has been updated to include all 2010 model year Lexus vehicles.
^ Location of HDD Navigation information has changed on TIS, which is reflected in this TSIB.
TSIB No. L-SB-0042-08 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding.
Introduction
Lexus models equipped with Hard Disk Drive (HDD) Navigation may have their map data, Compact Disc Database (CDDB), and navigation head unit software updated using the Navigation Update Tool and the HDD Navigation Programs Installer.
The Navigation Programs Installer is a PC application available on the Technical Information System (TIS) and must be installed on TIS Techstream or an equivalent PC. The Navigation Update Tool is an essential service tool and the device must be properly configured before initial use.
Follow the procedures in this bulletin to locate and install the HDD Navigation Programs Installer and properly configure the Navigation Update Tool. The HDD Navigation Programs Installer is a mandatory application that will be used to update the vehicles' map data, as well as the CDDB data.
This TSIB will outline two processes that must be completed to prepare the Navigation Update Tool for initial use:
^ Download and install the Navigation Programs Installer onto a PC.
^ Perform initial setup of the Navigation Update Tool.
NOTE
^ In order to perform the download and setup procedure, the PC being used MUST be put in ADMINISTRATOR MODE. Software will NOT complete setup if this is not met.
^ Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives, cameras, mice, etc.)
^ For additional details, refer to the "Navigation Update Tool Operating Manual" on TIS (under Diagnostics / Tools & Equipment / Navigation Update Tool tabs, "Reference Documents.")
Warranty Information
Required Tools & Equipment
Application Installation
The Navigation Programs Installer should be installed on one or more of the dealership's TIS Techstream units, the TIS workstation, or any equivalent service department PC.
Minimum PC requirements for the application to operate properly include:
^ Internet Explorer Version 6 SP2
^ 512 MB RAM
^ 1.0 GHz processor
^ 20 GB free hard drive space
^ 2 free USB ports
Download and Install Navigation Programs Installer
1. Turn on TIS Techstream.
2. Log into TIS
3. Download the "Navigation Programs Installer" from TIS.
A. Click on the TIS tab.
B. Click on the Diagnostics tab.
C. Click on the Tools and Equipment tab.
D. Click on the Navigation Update Tool tab under Tools.
E. Click on the "Navigation Programs Installer" under Available Software.
NOTE
If the TIS division preference is NOT set to Lexus (under the My Account area), the Navigation Update Tool tab will NOT display. HDD Navigation information is a Lexus ONLY TIS option at this time.
4. Click Run from the "File Download - Security Warning" screen to begin download.
5. Click Run to install program onto PC.
6. Click Next.
7. Ensure the "Everyone" radio button is selected and click Next.
NOTE
If "Everyone" is NOT selected, future installation errors could occur.
8. Click Next.
9. Click Close.
Tool Setup
Perform Initial Setup for Navigation Update Tool
WARNING
Do NOT perform setup if you have key files loaded onto the Navigation Update Tool with an older version; otherwise, the key files could be erased and key files CANNOT be recovered. Call the Denso Nav Help Desk for assistance.
NOTE
^ In order to perform the following procedure, the PC being used MUST be put in ADMINISTRATOR MODE. Software will NOT complete setup if this is not met.
^ Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives, cameras, mice, etc.).
Setup ONLY needs to be completed once for each Navigation Update Tool.
1. Open the Navigation Programs Installer by clicking the icon on the desktop.
2. Click Setup in the "Navigation Update Tool Main Menu".
3. Connect the Navigation Update Tool and press Continue.
A. Make sure the USB cable is secured in both the PC and the Navigation Update Tool USB ports.
B. Connect A/C power supply.
C. Turn power ON and press Continue.
4. Click the desired default language radio button and click Save and Continue Setup.
5. Allow Setup to complete (it requires about 1 hour).
NOTE
Do NOT turn the PC or Navigation Update Tool OFF during Setup.
6. Confirm that the Setup screen appears with "Setup has finished successfully".
If an error screen appears, please consult the on TIS (under Diagnostics / Tools & Equipment / Navigation Update Tool tabs, "Reference Documents:")